2017 can am renegade exle hib castle nut, can anyone share the nut size or part number? Having an awesome time finding this.
@jimiorezzoli5 ай бұрын
I wasn't sure if a c-clip was holding it in or what, watching this made it simple to figure out. Thanks!
@nmccarthy91898 ай бұрын
don't be seating bearings using the inner race people. you will destroy the bearings 👌
@kamui35211 ай бұрын
excelent
@cd1772 Жыл бұрын
Lmfao and the next thing you’ll need is unicorn horn dust and Thor’s hammer
@mrblackllc Жыл бұрын
You're using force on the inside of the bearing ...not a good idea . Hope it worked for ya.
@ZachKelley1022 Жыл бұрын
Do it go back together just fine without removing trailing arm
@motododo4626 Жыл бұрын
Would this be accurate for tearing down a 2013 outlander 650 engine?
@Winnipeg_Jets_Fan Жыл бұрын
LOL "Mike, i'm gonna need your tool"
@juansalazar1153 Жыл бұрын
Does your timing mess up when you remove the fly wheel?
@denissarko7098 Жыл бұрын
Hi give me your email please
@bradsapp2760 Жыл бұрын
Is this the same as Can am Commander
@diegonunez2927 Жыл бұрын
..
@CaleNormore-yt6kb2 жыл бұрын
I don’t quite understand how to pull the front drive shaft out with the motor in the frame. It seems I can’t move the motor back far enough or get enough room to get the yoke fat enough away to flip it up and remove it.
@craigswoboda92572 жыл бұрын
I used a sledge hammer and just swung it, worked perfect. Thanks.
@mikegarrett38152 жыл бұрын
This is an older G1 from what i see... Not the same with a G2
@gol87232 жыл бұрын
This is not charging, this is testing
@brianbyers26822 жыл бұрын
headphones LOL!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
@billy78052 жыл бұрын
The inner part of my primary is seized on i have tried everything
@LJ_washer_Dryer_SwampJuice852 жыл бұрын
We all do bud thats life!! But you did a dam good job on explaining the build step by step only one I’ve seen on KZfaq that actually took there time and was an average person that’s doesn’t have all the mud build channels and is a normal so diy guy. You get 💯 from me using your video for my gen 1 as we speak rite now… 👍👍🔜🔜🔜keep them coming bud
@sethwylie78752 жыл бұрын
Lier
@sethwylie78752 жыл бұрын
Lier
@tracecampbell36923 жыл бұрын
Where did you get clutch puller I have to fix my rod bearings
@dustinstaggs46023 жыл бұрын
How did you go about removing the dipstick tube??? It's giving me a fit
@westjl2jw3 жыл бұрын
Thanks a ton for these videos. I just bought a 2007 outlander 500 rebuild project. It has a loud motor knock so I am doing a full tear down. My first time and your vids helped get me over a few rough spots. Just about got it apart so will see the crankshaft area tomorrow. So far I see flakes of metal in one of the timing gear housing. The chain guide is frayed on that side as well. And the last bits of oil draining out look like chunks of mud! The pistons are fairly carbon coated and the plug tips are really coated up. Machine only had 2400 miles so it has been abused or not maintained. I hope I can get it fixed up. Want it as a second machine.
@johndragonman3 жыл бұрын
i have one of these engines.. less than 100 hours of use on it and the tensioner.. or something failed causing it to slip the timing chain off the sprocket. the chain never broken but sadly it has taken out the mount for the horse shoe clip.. so i think the engine is a scrapper :( the tensioner looks to have melted?? all molten plastic around it
@denisrosu43053 жыл бұрын
What you mean the nipples of roads to be out? I wait your answer please!
@alberthachfeld65143 жыл бұрын
Great video, great job!
@jaywilliams0521083 жыл бұрын
Wats the torque specs for 8mm pto cover bolts?
@burlcoco3 жыл бұрын
Hey man good info. How can I get a hold of you i have a question about an 800efi outlander 2007. No one seems to be able to answer.
@jimturcotte55194 жыл бұрын
Worked for me on the first try. How much of a job is it to get the new shaft in? I will be getting the new one in the morning. Any tricks to getting it in?
@davidlaye23064 жыл бұрын
I replaced the spragg clutch and put it back together. Now the flywheel turn with starter but not the engine???
@lorenzobarbosazavala85464 жыл бұрын
Good morning, I have an Outlander 650 and when you release the accelerator it makes little jerks, you don't know what it can be
@joshuaramirez29114 жыл бұрын
Thanks for the upload went riding last week and heard a loud clank sound in motor just started pulling mine out this video will help he a ton! Thanks!!!
@Browner394 жыл бұрын
So I have used a tie down strap like you and 8lb sledge to try and pull it off. Both side won't budge. Any suggestions. I have a 2004 outlander 400 XT. Want to do wheel bearings, just can't get the damn thing off.
@nstockert4 жыл бұрын
Ok let me look tomorrow in the service manuals it may have any inner keeper in the diff
@Browner394 жыл бұрын
@@nstockert I managed to get one side out. Waiting to get bearing to pull the other. Just gonna grease that one as the one I pulled seemed fine, just needs grease I think. Thanks for getting back to me. Gonna do the front to grease so will see how that is gonna go when I get into it. Hopefully a little easier.
@justbraaapit23114 жыл бұрын
Do I need to pull the motor to get the magneto out?
@nstockert4 жыл бұрын
No you sure don't just remove the floor board to help you access better
@renegade97584 жыл бұрын
What crankcase Bolt torque specs?
@murrayw724 жыл бұрын
With the headphones lmfao! Thank you for the smile!!
@vernoncampbell10704 жыл бұрын
I have a 2006 can am out lander won’t start put new battery in it ran then died when un connecting battery?? Dose it have a charging issue
@pallikorva114 жыл бұрын
Dude, you should use the old bearing to push the new one in.
@adrianmorar27214 жыл бұрын
Helo from Roumenia thenks form informansin!
@robertfoster43894 жыл бұрын
2008 can am renegade ho efi. I need help bad with putting the stator cover back on. Theres a few issues, if you could contact me through fb messenger thatd be great, or even a live video chat
@brokensmile84875 жыл бұрын
Hello, I have a 04 Can Am DS 650 and there is oil in the stator cover. Is that normal?
@questionmark43485 жыл бұрын
Those fuel line clips, I'm sure you figured this out already but for everyone else... you don't lift up on them you "push down"... pry them up and you will break them every time. Let the fuel pressure out of the line then push in slightly on the hose while pushing down on the clip with your thumb....that will release the clip then simply pull the fuel line off
@foxcrosss66695 жыл бұрын
Good idea
@foxcrosss66695 жыл бұрын
What time i need for this work?
@juanmaldonado96405 жыл бұрын
How did you put in the main crank bearings
@Hectoraka3005 жыл бұрын
2008 canam outlander 500 heads the same as the 800 ? Same year
@jannettasgarage72475 жыл бұрын
Hey buddy trying to get some info from you also asked you on another video you can please text me back that would be great