I neend this pump in quantity please contact me if any one have from Pakistan
@PerpetualMan225 күн бұрын
Loved the gear puller joke, should always lubricate the bolt in center of puller and use a 1/2 drive impact wrench (300 lbs of hammer torque)
@poulgammelgaard88684 күн бұрын
Thank you for commenting
@evanjones2539Ай бұрын
Great informative video, cleanliness and zero bullshit...
@poulgammelgaard8868Ай бұрын
Thank you very much
@martinamadsen812Ай бұрын
Thanks for sharing this video, unfortunately it lack the close-ups and explanations which would let me fix my Ferguson's injector issues that occoured after I took out the small fuel filter, spring and plunger, and apparently did not put it back, or added seals? I need very detailed video and explanations to understand what, if anything I need to rectify. Stay safe, regards Niels.
@andresgomez48343 ай бұрын
Muy buen video master👏👏 , ¿para poder aumentar o reducir el caudal de petroleo que perno debo mover? Gracias
@poulgammelgaard88683 ай бұрын
Thank you for commenting
@bojanmilovanovic80243 ай бұрын
Got one like that myself. Best tractor in its category for sure. Plus, if you have kidney rocks, that seat will fix it in no time :D
@poulgammelgaard88683 ай бұрын
Thank you for commenting. Good luck with your tractor.
@joseluispereiradeoliveira63454 ай бұрын
Quri saber o que seria vem diesel ate abomba enao sobe pros bico obg ja agradeço que deus oabencoe sempre ate
@poulgammelgaard88684 ай бұрын
Maybe the metering valve is stuck in the stop position
@user-mp5pt7zq3g5 ай бұрын
Hvilken olie skal der på pumpen efter reparation/service?
@poulgammelgaard88685 ай бұрын
Jeg brugte bare alm 15 w 40, samme olie som motoren.
@rukmanjakhar61165 ай бұрын
Hey I also have the same pump in my ford 3000 but the condition of my pump is ruff 😅 can you find me or source me another same pump if possible.I live in India there are only 10 tractor with same pump in India which are imported from England at that time and it’s impossible to arrange that same pump here. So can you help me to arrange that pump. I am waiting for your reply 🙏
@user-fw8ux5ti4n5 ай бұрын
Does a defect in the diesel injector cause a weakness in the tractor’s torque when plowing? Please answer
@3sparewashers-lg3gf5 ай бұрын
It could, or it could be low compression, retarded pump timing, or low fuel pressure
@Mrbigp596 ай бұрын
where to buy all the little items not in the kit in the USA
@jordibret6 ай бұрын
Jo tengo el massey ferguson 35x con el motor todo nuevo y la culata ! Pero cuando esta a relenting siempre hacer mucho humos 💨 nose que hacer ?
@user-ke9xx4dx2b7 ай бұрын
Where did you order the plunger in element from?
@poulgammelgaard88687 ай бұрын
injectionpumps.co.uk, You will also need the special socket for the valve holders
@dantediaz66727 ай бұрын
1:00:44 What is the name of the piece that you place in the video, from minute 1.00.44 and what function does it fulfill? Could it be missing from my pump?
@poulgammelgaard88687 ай бұрын
You would not be able to stop the engine, if it is missing. It is the linkage form the stop axle/stop lever and the measuring valve. It rotates the measuring valve and brings it in a position where no diesel can flow to the pump head. Injectionpumps.co.uk calls it "CAV DPA fuel shut off bar"
@antoniosa11157 ай бұрын
Trabalho espetacular. Tenho um mf35 para restaurar mas infelizmente não o vou conseguir com essa perfeição. De vila do conde vai um abraço.
@poulgammelgaard88687 ай бұрын
antoniosa1115 Thank you very much for your comment.
@MrBruce07777 ай бұрын
I have the Ford 3000 with this Simms Injection pump. Sadly the Injection pump was already taken off when I got the tractor So I need to figure out where it was set as per timing marks at the pump. My middle plunger is stuck ( Soaking in Marvel mystery oil ) Now it's in CRC Evapo-Rust said to work great on rust ) So far I have not found a socket with the right splines either to remove the top section. I heard it's 34 teeth for Ford where Metric is 33 teeth. Pump did not have any or much oil in the right hand section....
@poulgammelgaard88687 ай бұрын
Injectionpumps.co.uk have the special socket. If you watch my video at 42.55 you can see the timing marks under the little cover on the back end of the pump. With the ford 3000 on 19 degrees BTDC on the compression stroke it matches. You find the marks on the tractor flywheel behind a little cover on the bottom af the clutch housing. I find it easiest to rotate the engine, if I take off the starter motor and have acces to the teeth on the flywheel. To figure out if the tractor is on compression stroke, you maybe have to take off the valve cover.
@tarikchamonsimaochamon52478 ай бұрын
Muito chique. 10:52
@Fran_S25Argentina10 ай бұрын
Gracias
@JACKOMIO111 ай бұрын
Merci pour cette excellente vidéo
@poulgammelgaard886811 ай бұрын
Thank you
@RafaelZayas-ok7ub11 ай бұрын
Quiero conseguir bomba Diesel ,furgoson 3 cilindro Ford usada Rafael Zayas PR gracias
@motorhead4003 Жыл бұрын
Need a replacement plunger for simms injection pump off of a 1968 ford 3000 the lever that the rail turns on plunger is broken. Any suggestions? Thanks
@poulgammelgaard8868 Жыл бұрын
Injectionpumps.co.uk have the parts you need: Simms Minimec delivery valve removal splined socket. ID: F14A, seal kit for Simms Minimec 3 cylinder diesel injection pumps: ID S13, plunger and element for Simms Minimec pumps 512506-42, ID M6A.
@motorhead4003 Жыл бұрын
@@poulgammelgaard8868 Thank you so much
@motorhead4003 Жыл бұрын
Should all three be replaced or can the one that's broke be replaced only?
@poulgammelgaard8868 Жыл бұрын
You can replace just one, but I would replace all three, but after replacing one or more the pump needs to be calibrated. You could alternatively just transfer the lever from a new plunger to the old plunger if you have a hydraulic press. It has to be oriented exactly the same in order to get the calibration right.
@motorhead4003 Жыл бұрын
@@poulgammelgaard8868 Thanks again for your help sir.
@atproduction1775 Жыл бұрын
kzfaq.info/get/bejne/bZZimcVnntKcd6s.html
@roythewho Жыл бұрын
I have a 35x 1962 an my fuel pump dont pump any fuel to the 3 injector tubes, what can be the problem? Everything else is ok with the pump but nothing coming out of the injection tube holes
@user-ck5ye3pe1q Жыл бұрын
I have a pump that I fixed two months ago and then it broke. How do I know the original parts
@user-ck5ye3pe1q Жыл бұрын
How do I know the original pump head?
@josemmorab6794 Жыл бұрын
Nice video,can you tell me please where did you buy the gasket kit and additional parts?
@poulgammelgaard8868 Жыл бұрын
jose m mora b thank you for commenting. You will also need the special socket for the valve holders. Injectionpumps.co.uk have it.
@josemmorab6794 Жыл бұрын
@@poulgammelgaard8868 Thank you very much!
@stestrupholm-dyrkjorden Жыл бұрын
Tak for den detaljerede video!
@stestrupholm-dyrkjorden Жыл бұрын
Hvor fik du den lille gummidims til den knap man trykker ind for at give ekstra brændstop under opstarten? Bruger den altid i koldt vejr, men gummiet er ødelagt.
@poulgammelgaard8868 Жыл бұрын
Velbekom. Der sidder nok en næsten magen til på din Ford 5000.
What is the name of the tool used to remove that stuck cover with an impact wrench? It has a center punch and pry grippers. Thanks.
@poulgammelgaard8868 Жыл бұрын
Puller with three adjustable arms
@zfilmmaker Жыл бұрын
@@poulgammelgaard8868 thanks, that was very helpful!
@user-kb4no9ci1r Жыл бұрын
Буває комбайн Вольво 800 день постоїть і потім треба довго гонити стартером, а на протязі дня заводиться без проблем в чому може бути проблема?
@steve7931 Жыл бұрын
Ten Stars , I salute you , watched with awe and great pleasure , inspirational the best I have ever seen .
@poulgammelgaard8868 Жыл бұрын
steve7931 Thank you
@381alberto Жыл бұрын
Hola amigo tengo una bomba igual y no sale gasoil por.el purgador de arriba, el de abajo todo bien, si saco la tapa podré solucionar, desde ya muchas gracias
@poulgammelgaard8868 Жыл бұрын
Alberto meroni thank you for commenting. Good luck with your pump.
@MrJason34601 Жыл бұрын
Any idea where I can find a replacement cam ring at? Can't seem to find the A309E.
Hello engineer Paul I am justice in ghana I over haul this pump twice a week .our problem is quality of plungers they brought here in ghana
@j1166240 Жыл бұрын
Loved your video! Thank you for posting, You are very talented and thorough in your work.
@poulgammelgaard8868 Жыл бұрын
j1166240 thank you for commenting.
@TheTradeuser Жыл бұрын
was following your rebuild and tried to screw the cap off at 14:55. it broke off. What is this called and can it be ordered?
@poulgammelgaard8868 Жыл бұрын
Transfer pump rotor. There are different threads, left and right, inner and outer.injectionpumps.co.uk/?s=transfer+pump+rotor&post_type=product
@TheTradeuser Жыл бұрын
@@poulgammelgaard8868 Thank you so much
@TheTradeuser Жыл бұрын
After installing the end of the pump part at 34:32 shoud the shaft rotate without restriction. my shaft turns hits a restriction point every 90 degress. Are those rollers out of place?
@poulgammelgaard8868 Жыл бұрын
@@TheTradeuser At 38.34 you can see, it should rotate without any stops. Is yours a four cylinder?
@TheTradeuser Жыл бұрын
@@poulgammelgaard8868 yes
@samuelwotring633 Жыл бұрын
I'd like to see what you went through for the timing of taking the fuel injection pump off the motor? I understand you got to be careful when you do that but it goes on exactly the same way?
@poulgammelgaard8868 Жыл бұрын
When you bolt the gear back on the front of the pump, the bolt holes are slotted, so you can not be sure where it is correct. Before taking the pump off, you have to turn the tractor to 19 deg btdc on the compression stroke. There is a little plate to take off on bottom of the clutch housing where you can read the 19 deg on the flywheel. On the pump there are timing marks on both ends, as I show in the video.
@thehermitish1 Жыл бұрын
Thanks for the very clear and detailed video. Was just wondering what the behaviour of the pump should be when the timing marks are aligned? Trying to help out with the rebuild of a Ford which has a similar pump, though 6 cylinder, and when we have the marks lined up fuel still flows from the number 1 valve when trying the spill timing. When we supposedly line up all the timing marks the tractor still will not start and we are wondering if there is something wrong with the pump and we should remove it to look at getting it serviced.
@poulgammelgaard8868 Жыл бұрын
thehermitish1 thank you for commenting. I would remove the top element and check it for stuck plungers and stuck delivery valves.
@thehermitish1 Жыл бұрын
@@poulgammelgaard8868 thanks for the reply, I will pass the advise on to the owner. We are able to get the spill timing to engage but the timing mark on the plate is a good 60 degrees back from the mark on the casing. Regardless, something we will have to investigate further.
@matui6983 Жыл бұрын
You will probably find your control rod or rack may be in the wrong position for spill timing. Vaccum gov pumps are different to Mark 2 mech pumps like this and they are different to D-series Minimecs in adjusting the timing. Plus you turn the engine in direction of rotation so that with the side door of the inj pump off you can see number one tappet lifting and what you want is the first of cutoff. Then replace the delivery valve, button it up, bleed it and I always pop the excess fuel Button to bleed the air out faster than cranking it over with it off and she should fire up straight away..
@kenh3344 Жыл бұрын
Well, a very nice effort. Meticulously clean, before the repaint. You deserve top marks for the restoration. 100/100. Just look like it came out of the banner lane factory at Coventry.
@poulgammelgaard8868 Жыл бұрын
Ken H thank you for commenting
@edgarfuentescolque87662 жыл бұрын
Buenas noches, un excelente video, una pregunta. A que lo llaman poner en punto..?
@krelle3812 жыл бұрын
Hej hvor har du bestilt reservedele fra?
@poulgammelgaard88682 жыл бұрын
Hej Kristian. Det meste er fra injectionpumps.co.uk, de har bl.a. den specielle top til ventilholderne. en anden mulighed er: www.charnleys.com/part/leyland_middle/17h6606/fuel-valve-and-guide Mvh Poul
@gustavomansilla83232 жыл бұрын
Pa, me mire todo el vídeo, eres bombista , la verdad q es un oficio q mi hubiera gustado , y más ahora q creo q tengo q hacer la bomba de mi camioneta , saludos desde Uruguay
@JohnSmith-sf8gj2 жыл бұрын
What do I do if my data plate is missing?
@simonbrooke40652 жыл бұрын
Brilliant, thank you, I have to overhaul mine tomorrow!
@poulgammelgaard88682 жыл бұрын
Simon Brooke thank you for commenting. Good luck with the overhaul.
@simonbrooke40652 жыл бұрын
@@poulgammelgaard8868 fortunately, before proceeding to the strip, I replaced a broken bleed screw, and the engine started. I think I'm going to put the injection pump strip off for a winter job, unless the hard starting problem returns.
@luiscalderon61922 жыл бұрын
Great video, thanks for sharing your knowledge, i need to fix mine, but i can not find the kit, where can i get it?, tia!!
@poulgammelgaard88682 жыл бұрын
Luis Calderon thank you for commenting. You will also need the special socket for the valve holders. Injectionpumps.co.uk have it.
@brendenvosper77722 жыл бұрын
Why did you not speak to what you are doing?
@poulgammelgaard88682 жыл бұрын
You would not be able to understand my Danish language :-)
@JohnSmith-sf8gj2 жыл бұрын
I've had so many diesel mechanics tell me that the rebuild environment must be hospital clean, with dust free filtered air and paper suits. The engine will run away if you don't! I've got to spend 2 grand on a new pump they say! Yeah, I can do this. Thanks for posting.
@poulgammelgaard88682 жыл бұрын
John Smith thank you for commenting.
@emendoz18 ай бұрын
Mechanics sometimes fib. I run my tractor with diesel fuel I catch in a can from a long lasting leak and recycle it back into the tank. Been doing this for months and she runs just fine. I’m finally now getting to rebuild my injector pump now.
@eslpaKo2 жыл бұрын
Good BUT.... HOW DO YOU UNINSTALL the pump ?
@umeshchandrasingh30052 жыл бұрын
Good knowledge sir ge.thanks.
@poulgammelgaard88682 жыл бұрын
Umesh Chandra Singh thank you
@peteoconnor88082 жыл бұрын
I’m rebuilding this pump and I need the special spline socket that you are using, can you please tell me where I can get one. Thank you so much
@poulgammelgaard88682 жыл бұрын
I bought mine from "injectionpumps.co.uk", it was out of stock many other places, where I looked for it.