any solution how to do yaw axis less tighten? in new x56 when using twist, I have to hold the stick so tightly that I can't operate the pov hat. all fingers must be closed on the steering wheel to keep the rudder in the correct position. but im afraid to open it. never forget how broke my 1st hotas before learn how to maintain in good condition :)

FYI 10 years later and this fix is still needed, 2024 X-56 from Logitech is almost ridiculously hard to move. I'm pretty sure they did this to make it feel like it is more substantial than it is. The worst part is that I have seen multiple people end up with broken throttle levers after a short time because of the insane torque needed to move the stock lever. - I personally took out as much of the super heavy grease as I could and replaced it with a synthetic grease that is much less tacky, now the thing moves like butter with just the right amount of friction.

helped perfectly with a brand new one, which i almost sent back. but be careful, almost broke the little cogwheels for the friction control.

This issue still exists in 2022, did you ever find a fix?

I just fixed my 2021 Logitech by removing the blades, this video gave me confidence to do so.

This gave me the confidence to disassemble the boxof my 2021 X56. Thanks Wydra91. The goop is clear compared to the white stuff in yours. I was removing it with Chux as tissue paper got stuck in it too. Personally, I prefer no friction (like Grim Reaper), so I took the blades out after removing the two screws that limit it from being raised too far by the friction wheel. Now it should be easier to control. It still holds position wherever I leave it. Can't wait to try it out.

Wanted to add my experience as well. I bought a new X56 in April 2021 and the throttle being hard to move was still a problem. Like many others have noticed, it does warm up after moving it a bit, but 10 seconds later, it returns to its original, sluggish state. I removed a lot of the "damping grease" as shown in the video, which loosened things up, but resulted in somewhat inconsistent resistance and honestly didn't solve the core problem (the throttle being harder to move intially than afterwards). I wanted it to be as smooth as possible. The way I fixed it is by simply replacing the damping grease completely with silicone grease. Remove as much of the old stuff as possible from both the blades as well as the grooves (I used kitchen paper) and add the silicone grease in its place. Be generous with it to overpower whatever small remains of the old stuff there still are (it seems impossible to get rid off 100%), but also to keep the throttle from feeling completely loose. The silicone grease then adds a pleasant, consistent and predicable degree of resistance all the way from beginning to end. Its really quite ideal. You can also still further fine tune the resistance via the knob on the side, if you so choose.

Another fix: first off good vid, this works quite well, but I find the friction can become inconsistent and still strong for fine moment with helis or formation flying/refuelling. Fix: I cleaned all goo out using WD40 then inserted a strip of soft foam (like in a couch) into each channel where the 'blades' go. It creates gentle friction without having a strong 'breakaway' force. So throttle doesn't jolt or stick when doing small adjusts... Best way I've found so far... Hope it helps someone. Happy flying

I know this is an old video. But you could get some nyogel 767a, and then remove all you want. And if it was too much, just add some nyogel back onto it. I use nyogel on the ball of my x55 stick. Gives it a wonderful feel.

That sticky goo caused the wires to break which I had to replace and is still holding after countless hours in ED, XP and DCS. A long story short, I removed the goo with earbuds and replaced it with quality expensive silicone grease and all is well with less friction but still stiff enough to fly the airbus with throttle in climb position. Elite Dangerous is quite heavy on the controls especially in dog fights.

Hi Wydra, thanks for the 6-year-old video. I added a bit amount of liquid soap to friction blades with ear cotton buds (Q-tips). Without removing any grease. Now WORKS LIKE A CHARM. Also friction knob working as expected.

I just got the X56 from Logitech last week. This video and a plastic spudger were used to remove some of the sticky clear grease. I managed to "SAVE" the grease by scraping it off and depositing it back on the bottom base plate where there are several small plastic " HHH " shaped blades. Now the grease is stored there for future adjustments and is not going anywhere. Thanks for the 6-year-old Video!

This also works for the Newer X-56 from Logitech (the grey one)

Good vid still. The x56, both the Saitek (Madcatz) (blue decals) and the Logitech 2018 (gray decals) versions still use this dampening grease. The black and gray Logitech 2018 version comes with less on it to begin with according to their public change documents. But many people still remove a good bit of it. Use a plastic putty knife or a credit card to remove the grease. No need to tempt fate with a sharp razor in there.

I have a similar issue with The track clip PRO. If I roll at the center, it'll roll naturally as you demonstrated. However, if i pitch up 80 degrees the roll is no longer localising to 0 degrees across the X axis, but performs a compass effect around the point i wish to view. So irritating. Basically, once I look up the centre line becomes redundent when I roll.. This is using software from the date this is posted. Is there a fix we know of yet? Thanks

Ah yes noob virginity.😂

Great video, thanks! I did this, but somehow the X56 throttle friction wheel doesn't work now (as in "isn't connected right") So gotta open it again (no big deal) but what to look for to get it right please?

From the ass end of 2018, this was adorable... :3

Ouch, Old Stalker has always been a bigger threat than Shadow Stalker.

mine yaw to only one direction, complete waste of money

Necesito ayuda puedes ayudarme???

This is hilarious. You deserve more subs

I know this video is old but I really need some help with my X55 Rhino. The buttons(and scroll wheel) on the left throttle work fine from 0% to 99% but when you push it past 100% the buttons no longer register. Something is physically wrong with it. I've had it for two years and after not using it for about 3 months and turning it back on, it suddenly had this problem. Does anyone else experience this, and how do I fix it?

Thank you mate, totally got rid of the issue

Wow you suck at this game, you only have starter gear and it's hardly leveled😂

Wydra91, How do you use Video Processing mode on precision and not lose track? My trackir never picks up when in that mode

Will this also work for the followup model, the X56 ?

This episode was fun! Nice work Wydra91!

Just mount the thing correctly with bloody screws FFS!

Same issue here with new TIR5, did you ever get a fix?

I installed the Track IR, click on icon but nothing is hapening

thanks for reassuring me that all the screws are identical. i tried opening the base to see what was inside. i leave the screws inside so i don't lose them but i couldn't put the base back with the screws inside. now that i know they're all the same i can stop worrying.

Did you broke the throtle cables?

Very important to screw the stick and throttle down in front and at hip level. The bases have holes for screwing down. Look at an F-16 or F-22 cockpit and you will get the idea. Screw the stick and throttle in the right position and these behave way better. Removing the grease from the inside should be your very last resort.

Nice video, do you know How I can fix the Big rotary button on top of the throttle? Mine is stuck and I can't figure out how to open this part after removing all of the screws on the top of the throttle...

Having this exact same issue. Thanks for the demonstration. Did you find a fix?

This solved my problem with too high resistance with the X-55 throttle too. Thank you so much, man! Keep it up!

Just a quick tip for anyone wanting to do this - please don't use *any* kind of knife. The possibility of having a goof moment is far too great (you know it'll happen some day). What I used was an old pre-paid card but any kind of plastic card (credit card driver's licence etc) will do, most people will have one knocking about these days.

I removed too much of that grease and now my throttle become almost frictionless, not that I have any complain though, I want it to have much less friction anyways. Thankyou for the video.

Rubbish!

I have an x55 and they loosen up after a week of use so this is totally not a needed fix

How far have you disassembled the throttle? I need to disassemble the handle and replace the top rotary/push button (if I can source the part, whatever it is called. "push-button potentiometer" maybe?). Also the wiring in the left-hand throttle needs replacing as the buttons no longer work in the max position. Any tips on doing this? I wish I could get hold of a service manual for this thing.

I didn't use this to fix the sticking throttle (I have it mounted) however, thanks for showing the unit disassembled and reassuring me that undoing all screws was necessary to get access to the inside (I initially only removed the perimeter screws as I wasn't sure the middle ones were to split the base). As I suspected upon opening the unit one of the connectors was not seated properly resulting in intermittent operation of the lower row of buttons, re-seated the connector, unit works fully now :-) You saved me sending it off for an unnecessary repair so thank you for that.

thanks man !

I would use a Q-tip, but be careful not leave any of the Cellulose behind on the base plate. Well done on solving this problem

Just got a X55 and the first thing i noticed was how bloody hard it was to move the throttle. Wanted to say thanks for this tut. Did a great job of explaining why it so hard and how to fix it. Thanks alot! Now to spend 5 hours cleaning my desk so i can use it, lol.

Hahaha fuckin daniel lol making a water bed for Tony ROFLCOPTER lol

Nice (troll) vid :p ! Hey m8 you're just starting Warframe and have been rekted by the St*lker ? Well, like u I was, but if I can give you a hand to screw him, just ask. . . My vids will show you how I play, pm me in game if you're intrested :D

I vote to keep space squirrel on permanently!

No need to do this at all. The dial you touch 1.05 is the tension dial for the throttle. Turn one way to loosen it.