Alaskan Mancave

Пікірлер

@Lasersgoespewpew 15 күн бұрын

How many pound tow strap

@stanhutchins4365 17 күн бұрын

At first I was thinking oh man that isn’t for me. But then after all the tap was pulled off it looked absolutely amazing. 🤩 damn good job. 👍

@Correiacustoms 29 күн бұрын

What are your spray gun setting for the stencil layers? 1 to 1 on fluid and fan?

@mikebellofatto3023 Ай бұрын

Just out of curiosity where did get the stencils or just any stencils you like find in your area

@anthonyjancek2774 Ай бұрын

Love the shirt, I am from Michigan and grew up going to the Mystery spot.

@anthonyjancek2774 Ай бұрын

I am just starting to get into cerakote so your videos are perfect keep up the great work. I am using the cerakote C air cure for now and so far so good.

@VidarrKerr Ай бұрын

Amazing Work, truly awesome. The 3d effect is very real. I just want to know why you decided to change the direction of the stripe stencils. On the upper and lower receivers it is going up and to the right, but on the hand guard you went up and to the left. Also, what did the rifle look like fully assembled? Did you do the barrel and buttstock too?

@johnneidig7462 Ай бұрын

I'll try to make one to

@Driver732 2 ай бұрын

Hi, is this 1/2 or 3/4 copper pipe ?

@WHunterHale 2 ай бұрын

You’re talented in all your videos!

@BigMrAC 3 ай бұрын

Really thorough video explaining your process! Awesome!

@Sert-ELOfficial1989 3 ай бұрын

How long do you keep in the oven after each spraying and at what degree Thanks

@clintonsiles709 4 ай бұрын

Looks great thanks for the details I going to try my hand at it

@CasualInTheTrees 4 ай бұрын

At what PSI did you blast the wood at?

@edwardgrossman295 4 ай бұрын

What is the purpose of the spray bar, why do you need it???

@Nate1776_ 4 ай бұрын

What media did you use? Thanks.

@kalebhensley7868 4 ай бұрын

Great!

@KiNgChArLeSIII3006 4 ай бұрын

Can you get optics with illuminated reticles cerakoted like this? Will the oven mess up the electronics in it??

@Sert-ELOfficial1989 4 ай бұрын

While I'm doing the currying, the plugs bounce every time, and so do you Thank

@Sert-ELOfficial1989 5 ай бұрын

Do you go over the hooks with a sandblaster after several coats of paint to prevent paint build-up?

@jeffmockus5400 5 ай бұрын

I took a used recovery strap, cut a piece off and duct taped it to the drum. Once you get a couple of wraps its tight enough to not slip. Works great and super simple.

@hotcurdsinyurmudder 5 ай бұрын

The music is pissin me off.

@jimputnam7539 5 ай бұрын

That was a incredible transformation for that old battle horse!!

@johnwalter6410 6 ай бұрын

If you use an airbrush on the stencil portion you can get solid saturation without leaving a hard edge,

@hawwwgjaw 6 ай бұрын

Where you get the stencils?

@Sert-ELOfficial1989 6 ай бұрын

What exactly do you use to degrease and how long does it have to sit there in the tub and then when it comes out of the oven don't wipe it with anything and wash it right Thank you

@Tigris_River_Sand_Fleas 6 ай бұрын

Nicely done! Closer to Anchorage or Fairbanks? And what are your thoughts on cerakoting a base color down like white, using Krylon over that and finishing w/ cerakote clear? And lastly, do you have an opinion on cerakote micro slic?

@Johnsonhomeplace 7 ай бұрын

Can we see it in action

@jameskennedy8329 7 ай бұрын

Pete?!

@juanbravo7130 7 ай бұрын

Are you handling the small parts with no gloves on after you removed them from the acetone?

@brianpost8827 7 ай бұрын

How long did the strap last. Do you think it will hold up to an 8 hour day plowing sidewalks ?

@alaskanmancave5301 7 ай бұрын

Aa long as you dont raise it up too high it will last. I used it for my driveway for 2 years. My kids would break it cause they would raise it up past the plow's stops. I would just tie it back on till I ran out of strap. I never broke it once myself. I would still recommend it several years later.

@Moose_yo 7 ай бұрын

Beautiful

@cathybaschuk1285 7 ай бұрын

Should wear gloves ,those wires hurt

@guyromero9761 7 ай бұрын

Did you fully cure this at 2:50 for 2 hours with stencils on

@REDNECKROOTS 7 ай бұрын

Should the acetone be plugged from going in the barrel???? Thanks

@MrBinofacio 7 ай бұрын

Just what i needed... thank you

@getbrainseeds 8 ай бұрын

i want to do this using fde as base color od green and some kind of brown maybe coyote dark brown,nice job

@sachmo0196 8 ай бұрын

Not new but...A young man on KZfaq shows how to "divert light" via plastic and bending (cloaking him). Wait till Magpull really "see's" or doesn't. Magpull, send me a check :)

@sachmo0196 8 ай бұрын

Looking for ghosting for your weap can be difficult. I saw this and added it for one reason. I wanted mine to look (regional) yet, look like a train wreck (don't know what your looking/seeing...at). Take James Deans car (after) then clobber more and rust it...Train wreck.

@johnrogers4358 8 ай бұрын

Did you sand blast the gun first?

@callmethreeone 8 ай бұрын

LOL, why?

@captseamus 9 ай бұрын

I just cut off the bad piece of winch rope and reconnected the tow hook to the remaining piece of original rope. Think... You got 50 feet of winch rope! Double knot the rope at the hook connection..

@SETTAPERFORMANCE 7 ай бұрын

How lofted do you get a break at the double knot… I’m on my first synthetic rope and was looking at ways to fix the end if it breaksss..