A cut piece of paper clip under the bar will work and won’t void your warranty

Keep your orange foam earplugs to use as soft bullets…primer is enough to shoot them across the room

Where can I purchase these pins?

nice work 👍👍

This great video got my Interarms Virginian Dragoon SAA clone back in fighting shape!

Buy real AK from Europe, not US shitty clone.

Thank u for having the patience to do it for all of uss

Bought my P11 and had the EXACT same issue no matter WHAT ammo and grain I used... Replaced ALL springs and STILL FTF issues. This firearm is 100% unreliable and deserves the death Kel-Tec gave it. Inferior, too small and I constantly struggle to fire it and not hit the mag release mechanism - and I've got small hands to begin with. Really a subpar firearm, lackluster quality, and doesn't matter what lube I've used it's still difficult to get into battery at odd times. Absolutely do NOT recommend this firearm what so ever...

Why would you remove a piece of history 😂

now its a cap gun

I was very curious. Exactly what I expected to happen. Thank you

Did you have it on a 9mm?

Would like to know why you use such a small hammer??

You showed us what to clean but not how to clean with wants best for both cleaning an best for firearm?

Cleaning all grease cosmoline is a concern for me! What soap used?

Have owned a tac ops for 7 years and not a single problem with it. Has been very accurate as well.

For everyone else, just skip the about the 4 minute mark so you can see what you’re trying to see.

Out of curiosity because im a new owner of a Taurus 605(.357/.38SPL) why’d he go with the 6.5 Lb Hammer Spring reduction and not the 9 Lb Hammer Spring reduction because my thought is that the 9 Lb Hammer Spring reduction would make the pull even lighter than the 8 Lb on Double Action / Single Action pull. Any tips or comments would be highly appreciated!!

Back 7 years later because i just picked up a P09 and this video is still helpful

You were pushing in an angle that’s why it was difficult

Well done! Great video for a new builder to learn from! Really liked the reaction rod technique!

How do you put on attachments like flashlights and pressure switches though?

Use a paper clip, not a needle.

I have a Coast to Coast model 367 pump .410 and need the left cartridge stop. I cannot find it anywhere. Mine has just a 4 inch slot in the receiver for it to ride in, no pins or pivot points seen. I got a part online from ebay but it is still not right. says for a model model 77 but its not right. Can you help?

Shooting high velocity ammo will Crack the slide. They recommend standard velocity ammo. Good thing they replaced your slide anyway.

sccy was a keltec copy by a former employee.

Thanks for doing this video, im a gun collector, i fixxed my .22 and .25acp, so they both work like a normal semiauto, but i also voided warrenty on both, they were noth cheap so i didnt care abot that. They are very reliable, never had a misfire or light strike, no stove pipesno double feeds, 100% reliable. With at least 1050 fps, or more, weak loads might mess up the reliability

I'm liking that side charge

Happy I stumble on his video. I was about to get a metal lathe. Great job , ThankU !!!

where did you get your new magazine want to order 1 for myself

I was putting together a 300 blackout and my headspace gauges were still 2 days away so I decided to make my own go gauge out of a 300 case but all I had was factory loads. Stuck the ammo in a vise and pried the bullet out and emptied the gun powder and had my own generic go gauge with the primer still in it. I still have it laying around somewhere and have been curious to shoot it. Watching this makes me more confident I won’t accidentally damage anything in the basement lol

With child and puppy really!!??????

Great video, very well done and easy to understand and follow. My question is the set screws. Are they just pressured holding the sight to the barrel. Or did you have to make a channel groove in the barrel for them to ride in?

Mine shoots great

When I built my Hungarian AK63-D I just added .006 to the back of a steel case and set the head space that way and when I got real set of 7.62x39 head-space gauges the GO gauge was just a little tight, but then I read where the AK is expected to have a little resistance on the GO gauge and they actually give a torque spec. The gun works perfectly!

My Mosin has an issue where the bolt will not easily unlock after firing requiring it to be hammered open. Mark over on Anvil though it was a dimple in the chamber from someone trying to polish out a rust spot, but I recently got a bore scope and can see it looks like when they chambered the barrel, they bored out the bulk a little too deep as I can see some of the drill marks right near the back of the chamber just under where the rim seats, so when they chambered it to get the head space correct, it failed to clean it all up and that is what the cartridge is catching on and locking it in place. The gun only cost me $50 so spending $350 on a barrel and another $150+ to get it installed on the ugliest gun I own isn't happening. I wonder, can you sleeve out and re-chamber a barrel?

You’ve voided the warranty on that gun by tinkering with the springs. If you’re dragged into court after a shooting you’ll be asked about modifications to your firearm.

Pretty poor explanations "I've done it so many times I just".

Love to see the cleaned up reassembled gun.

is it a series 80 it could have firing pin safety

Which T-Handle did you use?

I have a timney trigger on mine. It works great.

TRADE FOR A REAL AK

Nice build 👌 👍 thanks

Wow.They say revolvers have a simple mechanism.It's a Swiss watch!

Great video

Interestingly enough my HP22a is able to move from safety to fire and back without a magazine in place. My safety does not have the same section on it that you cut off on yours. I guess they didn't make all them the same.

"replaced recoil spring every couple hundred rounds, five hundred, or a thousand rounds or so." WTF? HOW MANY ROUNDS???????

This is the best video I’ve ever seen on any AK issues. I appreciate the time you took to do this, and it is very helpful.

I inherited one of these and I have trouble being right handed with the slide lock could I put it on other side