Where I can get config file?

Thank you for this video. Maybe you can answer the question of why we can only connect to these devices when the computer is on the same subnet as the device? This is something I cannot seem to sort out. When I used the default factory configuration, I could connect to the Slave device from any of my VLANs, but for the Master device I was only able to connect it from the same subnet (VLAN) of the "bridge" interface. It would be wonderful to be able to connect from any of my other VLANs. It is not a networking issue in our environment. The VLANs I am referring to have total access to each other

I wish it had worked for me.

Are Cudy routers reliable in the long run and if so how long would one last? Also isn't the cudy firmware already Open WRT but with slight modifications out of the box?

Ok, I can connect to the router remotely, but I can't access the devices on the local network. How do I set it up?

Can you throw the config export into a github gist or something? Thx!

Worked like a bomb

I am getting this error:"Failed to send data, error 64 Failed to send data, error 64 Failed to send data, error 64 Failed to send data, error 64 Failed to send data, error 64 Failed to send data, error 64 Failed to send data, error 64 Failed to send data, error 64 Failed to send data, error 64 Failed to send data, error 64 Failed to send data, error 64 Connection timeout for 'XW.v6.3.12.33412.240516.1806.bin' ⬆ Transfer of 'XW.v6.3.12.33412.240516.1806.bin' finished. " on Ubiquiti M2 Loco. Kindly Help

How do you view all these settings? They dont appear on the iPhone app. Does it have to be managed? What software ?

very clear explanations, Thanks a lot

Thank You! This video help me.

If both my WANs are PPPoE clients, I do not need the recursive routes or the check gateway right? Because if one PPPoE fails, it should automatically failover to the other one.

Great video! Nice solution for clients!

How will I get this to work behind a CGNAT? It seems all isp's are going to convert to CGNAT if not already.

Thank you this will help me with my hotspot clients now using Cudy AP with Powerlynx they are using Wireguard VPN to integrate with. 😉.

I works as I was expected. many Network bricked device's firmware issues solve via TFTP.🥰🖖

I wonder how speed compares when there are some walls between devices. My problem is not wifi speed in optimal, laboratory conditions, but in six story brick house when I can detect roughly 40 SSIDs and some old devices had problem to connect at 5m distance, some can so-so work through 50cm/20inch thick wall, but problem is mix of attenuation and interference.

meh, sounds good, doesnt work had to go back to countless jobs because the crimp contacts wasn't in properly. only thing this "EZ" crimper does better is the stripping, rest is meh.

This is the best of them all

Trash product

Thanks for creating this video! i will test it on my Router.

Excellent, I had tried watching other videos and this one works. Greetings from Chiapas, Mexico. Thank you.

Is this a good gigabit router to work on Verizon Fios?

when we can expect the video about setting notifications for failover and also making Logs in the system. ? highly appreciate it if you could provide this.

Nice and simple :)

its really usefull and really simple but real time handling snario for failover. i really appriciate it . thanks.

You can also do failover with route mapping.

did exactly as you explained and it works when manualy testing, but on every day use my first internet goes down like once every hour. when checking routes, one or both dns addresses is offline and never realy switches as they come back before it happens. :( causing about 30sec outage

Really helpful and very well made short video! Thanks a lot!

Fantastic video.

THANKS SO MUCH!

Mr Tim you are excllent, just simplifying everything ,great work Go on !!

woah, been looking for a vpn set up to my phone followed YT tutorials but could never get it right, this will work wonders, thanks :)

Thanks Tim 👍

Thanks, will definitely test this.

I must test this.

I’ve been using this feature with MikroTik’s iOS app and RB4011 router since its launch and it’s faultless.

I been using Alien for last 3 years unfortunately I am having an issue one day no WiFi in home upon connected with support I have find out my wifi antennas gone which really surprised me I have spent 389 euro to get my Alien and the reason to get this only reviews about it and I was thinking this is proper company who have been doing really good in network technology but soon I realised they are third class people as they said to me and informed me that you are out of warranty and we don’t do hardware replace so basically through your 389 euro into bin after just 2 year and 7 months of use I was really surprised a company of this size have no department or ethics to deal this kind of issue after this experience now it’s depend on you all if you want business with them people I say good luck because if problem arise then you will understand what kind of third class approach they have to deal with issues like I have my mission is spread mouth of word everywhere about them people I am going to warn everyone stay away and soon I am going share all screen short of thier response to me and all unsuccessful RMA responses they write to me it’s ridiculous and rip off.

I think i will lose connectivity to the DNS declared in the specific routes, untill the ISP goes back online. The DNS added as recursive are always routed through the same ISP, so I won't have routes to those DNS thorough the secondary ISP. Is that right?

Im watching this for caylus

The worst WiFi, always getting disconnected There’s always a problem

Thanks, it worked!!! only thing is that I had to maitein pressed the reset button for a long time meanwhile I connected the ethernet cable...

Very helpful video. Pity poe does not come on the hap ax hex lite 😢 I hate power cables to my routers.

for a moment, it looked like a wireless access point that can support CPE devices,lol mind was like, wonder if you can connect that to a rocket dish or sector antenna 😅

but ports redirection does not work on second wan :(

sound in the video is awful

Is it possible to configure some action/script on failover? like for example I have second connection to LTE modem that is powered using PoE and want to define some action/script that when failover occures to second port it will enable PoE on this port?

Hand drills saves so much time. very neat!

So I have the WR1300 I have tried getting into the settings using the default admin password but it does not work even after resetting the device, anyone know what I can do?

Range?