Hello, you are reffering to PSI's for Hydroblasting. This unit can be configured with 40k psi of water pressure too. Because its a robotic platform, it can handle high pressures constantly compared to a human body. The setup displayed is for Abrasive (sand) Blasting. For sandblasting we advice a constant pressure above 100 PSI (AT THE NOZZLE). Every PSI above 100 at the nozzle results in a 1.5% performance increase. The same goes if the pressure at the nozzle gets below 100, than, you willl lose 1.5% performance per PSI, besides other increases of inefficient abrasive consumption.
@girienterprise5801Ай бұрын
I want to buy...
@VertiDriveАй бұрын
Please get in touch at [email protected] and we will help you further.
@makantahi3731Ай бұрын
deep rust under the paint
@horthydro3987Ай бұрын
What is moving this up the ship?
@VertiDriveАй бұрын
Our crawlers are remotely controlled by an operator from a safe distance, the robots have 2 permanent magnet packs to ensure it can adhere to steel surfaces like ship hulls. Electric motors enable the crawler to drive in every direction on the surface.
@91LiljuniorАй бұрын
What’s the psi? I blast with 40k shotgun
@girienterprise58012 ай бұрын
I need its
@girienterprise58012 ай бұрын
I need to purchase
@VertiDrive2 ай бұрын
Good day, Please get in touch at [email protected] and we will help you out.
@glincoat2182 ай бұрын
I loved the m7 but the v400 would be a game changer for my work productivity 🙌🏾
@VertiDrive2 ай бұрын
Hi Alan, Your work with the M7 has been incredible. Note that there are many V400's available at BlastOne Australia to facilitate your needs!
Good day! please get in touch by sending us an email at [email protected] or visit our website (www.vertidrive.com/vertidrive/) to leave a message and we will be in touch shortly.
@lewislyreal26456 ай бұрын
$ price
@A.I.MUSICAL Жыл бұрын
What is the make of the paint
@uniworkhorse Жыл бұрын
Sick
@logannewport1448 Жыл бұрын
Barabarabara be be be
@floraaproduction9871 Жыл бұрын
We are into blasting & painting work. Will it be beneficial for cleaning rust from the tank. Which we do through copper slag
@VertiDrive Жыл бұрын
Hello, in this video, UHP Waterjetting is used for the removal of the contamination. This machine only has UHP waterjetting capabilities. We do have other platforms that can perform HP washing, UHP waterjetting, and abrasive blasting interchangebly with medias that do not have magnetic properties as our solutions adhere to the surface through powerful permanent magnets, using an abrasive media with magnetic properties will eventualy cause the machine detaching from the surface. Check out our other platforms in case you wish to use copper slag, cleaning rust from a tank is an excellent use case for our solutions. Check it out: www.vertidrive.com/products/m7-series/
@jamescrank255 Жыл бұрын
I'm curious towards the end of the video a secondary person is standing near the Crawler observing. Is this person also operating a dump valve or anything?
@VDJoey Жыл бұрын
This person isn’t operating a dump valve, the pump used for this job is a small electric one that gets switched on and off at the pump itself. However, the signal going to the pump needed to build up pressure can come from our control box as well. The person in this video is checking/ observing if everything works properly at the start of the work while the pressure is at approx. 100 bar only.
@CoatingsTalk Жыл бұрын
Great Video!
@adhi602 Жыл бұрын
How to get robot coat..
@glincoat218 Жыл бұрын
Thanks VertiDrive M7 was a fantastic tool and saved both time, money and most of all safety!
@redgator2854 Жыл бұрын
Slow no like
@WorksopGimp2 жыл бұрын
Looks new top-notch work
@VertiDrive2 жыл бұрын
With great coating adhesion comes perfect and consistent surface prep with a vertidrive unit
@AndreyDemshin2 жыл бұрын
Is ATEX Zone II acceptable for not empty tanks? I thought ATEX Zone I require…
@weldersandblaster2 жыл бұрын
Nice job. So much work just for some new paint.
@mahmoodhemad21113 жыл бұрын
Hello,where is your selling_place
@VertiDrive3 жыл бұрын
Hi Mahood, you can contact us via [email protected] or call us at +31 10 763 0200 and ask for the sales department