Thank you. Now I know it's better to just change it.

I didn't understand... I thought you were going to show the replacement of the (transmission) of the ge washer...🤷‍♂️

Thanks for the video dude you just saved me a bunch of money

Last time I had one do it I took off the cold hose and the screen was plugged up 😂

I had to tighten it a little more than 2 quarters but it was a great way to know if they were too loose. Thanks for the video. I just did this and it's spinning like a charm. If i ever have to tighten them i'm going to use blue loctite.

i thought this was such a logic repair so i ordered a set of collars as soon as i saw your video only to find out when i opened up my machine that top caps on for the springs in my washer are different, there's no lip to on the caps for the collars to clamp down on so now i guess i'm going to have to figure some other way to dampen the rods, maybe i'll try the safety pin hack temporally.....

Or a bad main control board

Nice

Hi, Great Video. My Samsung Microwave failed the same way. It was turning but not heating up. Many people are reporting the same issus and the problem is often the magneton. I didn't have all the testing tools but I was wearing gloves. I just replaced the Magneton and the microwave came back to life.

Didn't think about checking tilt level on mine, should help make sure the doors fully close each time. Learned something new watching this, thanks alot for doing this vid.

2:27 temp guns and thermal cameras will not see through most glass/plastic materials. You were likely just reading the temperature of a reflection.

if the dryer was working and then all of a sudden stopped working, light doesn't come on, doesn't turn on, etc., would this be the first thing you would do?

How do you know if the transmission is failing? What happens is that I changed the actuator and the capacitor on my washing machine and it continues to fail, it thunders like a plane taking off and stops and gets stuck in spin mode.

The old machines were better. Who cares if they use more water, they got a full load done in ⅓ of the time as the eco ones. Water is cheaper than electricity. Economical my tookus

What would cause the board to get fried like that?

After watching a video to clean out the same part you tapped. I didn’t see much debris. Plugged in and it didn’t work. I found this video and do the tap thing snd after couple of times tapping…MAGIC!!! What in the world!! Thank you so much!!!

Where are you pushing to help motor?

Same dryer same problem but i dont have the ability or tools to do the fix

Do you replace the entire thing?

My refrigerator and freezer is not working. I just woke up and went in my kitchen and everything in my freezer is thawed out. Ice is melted everything.

8:55 mines exactly like this one right now. No display. Nothing. What do you suggest I do? Get a new board?

Thank you for the knowledge! Found your video after replacing the broken dogs in the agitator. Agitator working now but Now I have to spin the basket by hand then the motor continues the spin. Basket spins on its own but sometimes needs a manual kick start to get it going. I have acquired this washer and believe it has been sitting for 2+ years not running? I’ve already ordered wrong parts but was still able to use the dogs out of the package. Please put out some links to the parts needed to do the exact repair in your video. I sure would like you to get any well deserved Amazon credit with the option to click a hyper link to purchase the parts. Thank you again.

Thank you so much! Its now working but I would like to say that now Its smels like burnt. What should i do, now?

This can work for fisher and paykel washing machine?

Do you know if these collars work for model mvwx655dw1? I just ordered a hub and agitator for it because it was shaking and not spinning correctly. The inner to outer barrels had a lot of play. It doesn’t seem like the 6 year old dampers are completely gone yet but I thought about trying this mod at the same time as the other new parts.

Super, My Kenmore was working, now froze on spinning cycle. May have open and free the brake.

Question. So it would be better just to replace them but since you dont have the replacement you use WD 40. How long do you think this will last?

This is good. I wish I could pick your brain about appliance repair.

I'm curious, how long will that last? We have a stove similar to that one and when that begins to be a problem, I'll sure give it a try.

I replaced mine and clutch or plutch and still does it any thoughts?

Yep great video. I just repaired a Simpson eziset. I used a friction/dampner grease on the wire shaft and other bits and it seems to working well so far. ( got this idea from a comments section on a repair video somewhere.) It's the same stuff they use in video game controls. Amazing sticky stuff . It was from NYE lubricants Inc , distributed by VKB- SIM Australia pty ltd. ( yes I'm in OZ ) . It was a synthetic hydrocarbon grease called Nyogel 767A. I have nothing to do with company. and there are probably other suppliers in the U.S. and other places. It came as a small jar in the mail with 5 grams in it. Enough for 4 suspension rods and cost $20-$30 with mail cost. Thanks hope this adds to all the great knowledge.

Great video to help me out with mine. The link is showing they are out of stock. I will try another that looks the same.

What does tapping it do? Why does that fix it? I was expecting a clog? I have the same issue and same washer. Just don’t want to call anyone in yet

good content. im adding this to my excel spreadsheet

The drain hose need to run up to the top of the cabinet or through an air gap fitting. What you did stops nothing but odor

Great video, very helpful and definitely a time saver appreciate the help.

THE TRUTH: Everyone is focused on making the capsule grip the rod tighter to reduce the shaking, This can help, but it is not the solution. The reason these rods work to stop the shaking is that there is a special grease that has been applied to the rod where the capsule moves. This grease has the viscosity of honey. It is thick and it is sticky. The capsule must move through this grease, and when it does, its motion is considerably slowed. This is what prevents the shaking from happening and dampens the oscillations that would otherwise occur. The bottom line is that if the capsule is in good shape, or can be repaired even with a solid substance or solid replacement, applying the grease to the rod in the area it moves through is the long term fix. If replacing the rods, also apply this grease if it is not already present on the new rods. This grease is synthetic damping grease lubricant. It isn't cheap, but you don't need much for 4 rods. I found it sold on Amazon for about $10. You get 2 10 gram tubes. If you are doing lots of repairs, you can buy a 50 gram tube for $26.

Just moved in this appartment and it has a unit that sounds like this....

most washers rinse with cold, so if you selected the hot with the cold line connected and you actually get cold it is going to try to use cold for the rinse and nothing will happen....

6:30 worst possible visual 😅

I can’t get my basket out to replace my drive hub. I have tried numerous things I think I might have to break it🤦🏾‍♂️🤦🏾‍♂️🤦🏾‍♂️

Would replacing the entire board work? And where would I find it?

Thank you, for posting this. Very useful. I was able to this information to reset mine so I did not have to call for service and waste money. Excellent information!

Thank you for this video, it helped tremendously. My husband replaced the Ignitor (and thermostat). ☕

Still waiting for video

Thanks for this. Trying to diagnose/research for my parents washer. (WTW5000DW2) Has a lot of trouble balancing properly, violently shakes with need to stop cycle and reset. Also, during spin *down* as the tub is slowing it makes very loud and abrupt clacking noises. Splutch?

OK folk if you have a Frigidaire, this is a good one to look at three thumbs up.

Those user interface boards as well as the main board were a big issue and probably still are a big issue with GE dishwashers.

Who keeps their kitchen cabinet in that state? Disgusting.

Thanks. You saved my bacon. Worked like a charm and cost me nothing. Thanks again.