I wonder why BMW e90x have such failure ? my 335i has 148km and runs amazing but iam nervous

What’s that needle you used?

What’s the needle you used called?

my eccentric shaft wont turn after tightening the cap bolts, any suggestions?

Thanks for your time and great content 👍

good morning, I'm trying to rebuild my n51 engine (2007 328xi). I've gotten as far as my eccentric shaft. I'm not sure of the position it should be in before I put the overhead springs back on. Any advice would be very helpful! Thank you

why are u using the old chain guide????? It wears out especially if it’s already colorised like this Allways replace them.

hello, I have a question I have my intake camshaft which is scratched and the caps which hold them are also scratched so I wanted to know if I can change these caps with another camshaft or these caps are integrated at the engine cylinder head?

Nice

Good cleaning and bleeding process established. Good job 👍

Man it's so satisfying to watch that I watched it more than once

I really hope you answer, I have just replaced my headgasket in my 328xi and everything was done properly, I made sure everything was locked at TDC when the head was taken off and put back on. I reassembled the entire valve train and now my intakes are not opening. I have a crank, but no start, intake valves are moving open. Any ideas?

Love your videos so much but I wish you would put part numbers in to

Thank you for this video it has helped me on my rebuild. On an n55 from a 2013 x5. Could you tell me if the crank seal is pushed too deep? kzfaq.info/get/bejne/lZp8l5abvq-7h2Q.html

Out of curiosity, did you plastigauge the King bearings? If so what was the difference in clearance? If not, what's the point? Trying to decide what to do after purchasing a car with this engine. Thank you!

Good, How much Loctite 193140 did you need for this engine?

This motor was tore torn obviously prior to being sold to u that’s why your torque specs are all over the place

Also do t follow BMW oil or any fluid change mileage so it way earlier ! And only use liqui moly fluids !

Liqui moly oil treatment fuel Treatments and 93 octane fuel will help with that carbon buildup.

BMW needs sued. So bad by every vehicle owner. All their shit is garbage all by designed to suck your 💰💸 dry !! Hate them all with a passion. And yet own x6 x4 328xi 550i. All are problem child’s. It’s rather depressing honestly. No car of these calibers should have such issues!! The N20 timing chain deal ong what a joke could they source shittier cheaper plastic for the the guides ? Hkw about the short rubber used for. All their gaskets that is so soft it eventually bakes to hard brittle plastic. How is plastic gonna seal oil 🤷🏼🤦🏼. These cars are trash. Do t buy one maybe lease one if you wanna waste that kind of $$ bit def don’t buy a used one and make damn sure u don’t buy a v8 trust me !!

With a good BMw scan tool u can control ea fuel injector shutting them off or on 1 st a time that would help u find your issue!

What was the solution? Did you have to rebuilt the engine?

hello, to install the hydraulic lifters you must not put the hole in the hydraulic lifters opposite the hole in the cylinder head where do you put it?

can you give the link for updated screws?

👌👌👌🌹🇮🇳🙏

Wow clean work. How long does it take to cure?

hey does this part has to be with the timing of the engine?

does the oil pump have a balancer or ??

So you skip the actual application of the sealant which is the reason I clicked on the video...

Should i replace both chains if the vehicle has 87K miles or can i put them back?

Hey i am rebuilding my N55B30A early 2011, i was wondering where i can find the information on most of the torque specs and specifications for tools needed, your videos have been so helpful

Highly informative video. Thank you.

Learning a lot. Thank you

Is it the same problem also with diesel 535 5 series?

Great videos and I enjoy the pace you go at. I’m the same way and always take my sweet time doing the tiniest thing!

Hey im building my engine spun a rod bearing. Do you have the torque specs ?

Hey im building my engine spun a rod bearing. Do you have the torque specs ?

podrías ayudarme con las tolerancias de los 3 anillos en un n55 en medida STD

what should be the max deviation of measurement in the deck?

Is there a way to know if my N55 has aluminum or steel bolts in the VANOS?

I have it as 30nm 90/90/45 deg

Man I love your videos I’m curious how those ACL bearings work. I put them in my n55 rebuild but I haven’t fired the engine yet.

Are those grip disk washers that go on the oil pump sprocket re useable ?

❤

what did you use to hold the crankshaft from spinning while tightening the main bolt?

what brand main bearings did you use ?

Great video! You mentioned a measurement from the wall for the piston squirters are you able to share that spec? Thank you so much.

Hello, I have a question I have a problem with my 335i e92 engine code n55 I rebuilt the engine it starts well but stalls after about 5 seconds, it starts then as a slight acceleration and cuts I have a fault present all the time after starting 2D11 lambda probe but before rebuilding the engine I did not have this fault, I have a doubt about the timing of my chain because when I did the timing to put the timing I forced to put the tool at the top for the camshafts, so I wanted to know if it could come from that in your opinion thank you for your comeback

What stone do you use and where do you get it? I've been looking for the correct stone but no luck. Thanks

While doing my pan gasket on N51 I broke the output side oil pump chain guide nub. Shouldn't be much of an issue you think? Car has been running for almost two weeks now after the pan service.