man!!! does it feel good to find a video that covers everything to the point.
@danielandrey30513 ай бұрын
Good yob sir. Thankyou sir !👍
@jasonberger83403 ай бұрын
I’m going to go get some lunch now so I’ll call when
@crispychicken27433 ай бұрын
This never works . It will fall off .
@soldieroftoughlove76354 ай бұрын
plumb bob
@a_w_bukhari75794 ай бұрын
Best 👍🏼
@crispychicken27435 ай бұрын
You forgot to mention. Make a mark with a framing quear 3 inches from the corners out and chalk line . To aline the coner post and 2.5 for the inside corners. Everything else you showed was good. Have you ever sided a full house. ?
@oneundecided5 ай бұрын
Thank you for this video. There are 5/8 and 3/4 J channels available in Home Depot. Which J-channel I should use for siding installation? Also, what is the distance from the siding strip starter edge to the concrete foundation and when do I need to install the bottom J-channel?
@oneundecided5 ай бұрын
Thank you for this video. May I ask what nails I should use for the siding installation on the 1/2-inch ODSB wall? The siding nails in Home Depot are 2-1/2 and 2 1/4 inches loos too long for me. Also how far the window or the door must stick out from the wall? And may I ask you how much the window has to stick out of the ODSB board to allow proper matching with the J-channel?
@Affordablebath_remodel16 күн бұрын
1 1/2" roofing nails might work for you
@HarveyWallbanger-ho2cq9 ай бұрын
Why would anyone put that crap on their house
@supertopiacorp9 ай бұрын
Please can you tell me how to wrap the windows when we decide to use vertical vinyl siding?thank you
@fefelch84869 ай бұрын
What kind of foam do you recommend using?
@robertallen313310 ай бұрын
Thank you
@aaronwiley543610 ай бұрын
I cannot believe that an industry generating large volumes of revenues have outdated install videos, you guys need to re-evaluate your marketing personal🤔
@billybobjosh11 ай бұрын
"leave about a 1/32 gap"
@89clavos11 ай бұрын
Great instructions
@susanschmid8697 Жыл бұрын
Any reason side cannot be used in place of soffit on a porch ceiling. I realize panels are narrower but see no other difference
@pa.fishpreacher6166 Жыл бұрын
Now you are ready to start the starter strip.... What came before this, you didn't say anything prior
@elenawalczyk5927 Жыл бұрын
Thank you for this tutorial- we were looking for inner corner post installation and so far it’s the only video we had found. Could you please explain how to seal the top of the corner post if there are no soffits above it ( just roof edge). Thank you again ❤
@wonheelee8033 Жыл бұрын
😊 good 👍 for the learning
@Brandon-no3vc Жыл бұрын
Where are you guys from
@ryangolden7893 Жыл бұрын
This always amazing
@josesantos-ov6vo Жыл бұрын
Me gusta aprender
@andrewjames1613 Жыл бұрын
Do you know a anyone near Buffalo, NY that will help get a job. I got 10 years in construction and have installed vinyl siding threw out but looking to grow and start up a business one day
@Brandon-no3vc Жыл бұрын
do u need lazer?
@Wayne_R Жыл бұрын
no and here's a much better video kzfaq.info/get/bejne/jd6Yd9h3z5mWnas.html
@maxo1987 Жыл бұрын
Excelente video, había visto la versión en inglés, la que no me complicaba, pero en su página web encontré la versión en español y mucha información mas, que acá en Chile, me hizo decidir por Vinyl versus fibrocemento. Felicitaciones a uds!
@garthbrooks4583 Жыл бұрын
Okay I like this
@EMTdrummer2 жыл бұрын
replacing corner was so quick it was worthless
@hulkhatepunybanner2 жыл бұрын
*Who sells vinyl soffit systems?*
@krisdomingues41362 жыл бұрын
No no my
@onceuponatimebyme2 жыл бұрын
How can I get this in English?
@tamerhamdy33082 жыл бұрын
wonderful
@jamestomaszewski67222 жыл бұрын
Your instruction video covered it all. The tips and tricks should help make my garage project a breeze.
@johnharris81912 жыл бұрын
No need for a level, measure down from the overhang on each end of the wall and snap a line. That way your last piece at the top will be the same width. If not, the job will not look good even from the road. TIP: If it looks level, it is level.
@joesmith4050 Жыл бұрын
This is what I was looking for, thanks for your tip. One year later 😊
@IamthetruraBu2 жыл бұрын
Have a situation where the crimping isn’t as durable and is flimsy. Could I use a silicone calk to tether it to the rest of the vinyl paneling?
@wlcswimm2 жыл бұрын
Meanwhile any vapor traped behind the vapor barrier goes into the window👍next time put flashing directly onto the plywood.
@scottdavidson47922 жыл бұрын
Too long of ads.
@scottdavidson47922 жыл бұрын
Stop with all the long ass ads. If it can't be skipped find another job.
@sarrenredmon18332 жыл бұрын
Get it right fuck-wagons you don’t need any fucking “vapor barrier” loser coconut
@GE0RGl0S2 жыл бұрын
what size thickness plywood should be used for vinyl siding, 1/2 or 5/8 inch?
@MentalHealthWithBen2 жыл бұрын
Either
@mikecase9365 Жыл бұрын
Nothing below 1/2 in but you could have anything above the min
@ezyjack8262 жыл бұрын
thanks for the great video. I'm going to be siding a steel shipping container. how can I attach the siding since I can't nail it? ty for any assistance you can give.
@modthirty2 жыл бұрын
Furring strips?
@lucashershberger3111 Жыл бұрын
maybe predrill and use screws,
@ezyjack8262 жыл бұрын
thanks for the great video. I'm going to be siding a steel shipping container. how can I attach the siding since I can't nail it? ty for any assistance you can give.
@timothyschreiber83382 жыл бұрын
I would install wooden strips vertically like studs, then nail into those.
@howardzhang56832 жыл бұрын
Is the material you used a soffit?
@darreldennison45732 жыл бұрын
"if the span is more than 16 inches" I never understood why they don't make 16" wide soffit panels. It is very annoying for contractors to only have a 12" option. 16" is the standard spacing, so why don't they make 16" panels?
@theyangview1898 Жыл бұрын
Certainteed ventilated soffit is 16” spacing for furring
@charlotteillis13282 жыл бұрын
Get off my phone
@bub87522 жыл бұрын
Still have storm damage from ida and having trouble getting some one out to install, heavily leaning towards doing it myself
@daveat9572 жыл бұрын
why do you nail the utility piece into the corner piece? wont the stop it from moving up and down for expansion? shouldnt you line up the slots? I'm pretty sure you're wrong about the utility trim at the top of the wall. that would be impossible
@pa.fishpreacher61662 жыл бұрын
starter strip will not move like the vinyl will
@nahidsanaei10373 жыл бұрын
Very informative yet the background music is irritating. Please nu music for your next video! Thank you