Neurotic RC

Пікірлер

@tonydetwiler2624 3 күн бұрын

should put a big ole brushless motor in there instead it will get up and go better from a stop

@NeuroticRCshorts 3 күн бұрын

Brushless is definitely better hands down I personally like the nitro with its engine factor.

@tonydetwiler2624 3 күн бұрын

that just shows how junk them engines are traxxas sucks big and nitro is just too much hassle, brushless is better acts like a rc and not a old car that doesn’t run right

@zanderflander7880 22 күн бұрын

That was enough loctite for 27 screws😂

@zanderflander7880 22 күн бұрын

Is that company treal any good? I thought they were just the cheap stuff like injora?

@NeuroticRCshorts 19 күн бұрын

Treal is one of the higher to mid grade companies. They are definitely more expensive than injora but all companies have great parts.

@a-trickygamer 24 күн бұрын

I just did this swap too. What needle carburetor settings do you recommend for break-in.

@NeuroticRCshorts 23 күн бұрын

i would just do the base setting what the Manuel says. im in colorado so it really depends where u live tbh. but for me i had to make my high speed needle extremely lean almost all the way down for it to be tuned properly. i would watch some vids on tunning and just do what the base tune is in the Manuel. but u want it to be more rich during the break in.

@TaylorGang978 28 күн бұрын

you skipped over the part where you took off the drive shaft from the axle housing . i have a king sling and im trying to replace the front axle on and i cant figure out how to detach the slider from the original housing

@NeuroticRCshorts 27 күн бұрын

That’s a completely different truck… this is for the lmt mini the 1/18 scale monster truck. I never did a video of the king sling or have one. This video isn’t about the king sling. Please watch a video that’s actually about your truck so theirs no confusion not every Rc car is the same…

@NeuroticRCshorts 27 күн бұрын

There are no necessary clips missing from this video and shows everything that you need to change the driveshaft.

@user-yi4jk6ro4p Ай бұрын

nice car but what is a dyno

@NeuroticRCshorts Ай бұрын

A dyno is what measures how much horse power and torque a car has. They are actually very similar to emissions test dyno if you have that where you live. But that’s just for reference. Look up like a Toyota Supra doing a dyno pull!! It’s very cool in my opinion!!

@user-yi4jk6ro4p Ай бұрын

@@NeuroticRCshorts Awesome

@Wings_of_foam Ай бұрын

Not quite a Dyno yet ;)

@NeuroticRCshorts Ай бұрын

Close enough!

@Wings_of_foam Ай бұрын

@@NeuroticRCshorts Where is the electronic to measure torque and hp? As far as i see it, you just made the rollers, or did i miss something?

@NeuroticRCshorts Ай бұрын

It’s supposed to be a model… it’s not seriously a dyno.. like come on have you ever seen a small dyno like that and can read the hp and torque and the many other things. It supposed to be a fun model/stand for the miniz.

@Wings_of_foam Ай бұрын

@@NeuroticRCshorts Ah, I see. My bad dude. But you did make a nice build and it clearly works well. But admit it. How cool would it be if you made it so it would show speed, HP etc :) I know I wouldn't be able to do it though, haha.

@allaspectsrc4178 Ай бұрын

Nice..good information..I just got a tmaxx and I'm interested in a dynamite 19 this video is going to help me out alot ..Thanks for sharing man

@NeuroticRCshorts Ай бұрын

No problem 👍 thank you for watching! I try my best to make it as informative as possible!

@NeuroticRCshorts Ай бұрын

links don’t work that well so another way to find it just go on Etsy and type in RockyMountainKrafts. Thanks!

@minecraftmonsterjam9791 Ай бұрын

I don’t like how low the sway bars are on the chassis If they were a little higher and the arms were a little longer it would prevent any 4 links from hitting them and bending them over time

@NeuroticRCshorts Ай бұрын

I agree to a certain extent. If they raised them much higher they would be hitting the shocks next. The best option they could have done I personally think is to just make them plastic and not have the metal rod.

@KAMPFER984 2 ай бұрын

What did you use for the track lines?

@NeuroticRCshorts 2 ай бұрын

Check out my ultimate mini z guide and I have all of the information on how to build that track!!

@lizardgalaxy 2 ай бұрын

Thanks for the awesome video! It helped me out alot 😁

@NeuroticRCshorts 2 ай бұрын

Glad it helped!

@larrythodgson7230 2 ай бұрын

Nice job 👍

@NeuroticRCshorts 2 ай бұрын

Thanks 👍

@chrisdolan9792 3 ай бұрын

Keep up the great work I'm enjoying the channel! Try some heavier wt shock fluid to slow down the suspension and stop the bouncing

@NeuroticRCshorts 3 ай бұрын

Glad you like the channel! Is that what you did to your lmt? Seems counterintuitive heavier shock oil makes the suspension even stiffer which then gets less dampening.

@betieakumaai8927 3 ай бұрын

I watched your vid multiple time..today i bought my own Kyosho..cant wait to get my hands on it..your vid was very helpful

@NeuroticRCshorts 3 ай бұрын

Thank you for the kind words!! You’ll love your mini z!!

@GLRange1 3 ай бұрын

Flywheel can't handle 3s...would be well over 30,000 rpm and even if it did work the corrections it makes would be overly violent, you can do 3s with a Castle voltage regulator though.

@NeuroticRCshorts 3 ай бұрын

No it can’t handle 3s but people buy this special esc that can direct 2s voltage to the flywheel. That’s what everyone does to run 3s Kevin Talbots did a video talking about it. So yes the flywheel can’t run 3s but you can run 3s just not 3s voltage to the flywheel which is what this esc solves.

@GamerFromTheHood 3 ай бұрын

GO GET YOUR MINI Z NOW ‼️ 💯🦾 FUN HOBBY FOR BEGINNERS TO DRIFTING…

@gkujae5576 4 ай бұрын

How those new sway bars holding up !

@NeuroticRCshorts 4 ай бұрын

Really well!! They seem to keep it planted more but kinda depends

@jmartin4911 5 күн бұрын

Still holding up well? The stock metal rods are constantly bending on the front axle

@RCRoads 4 ай бұрын

I guess that's the week link. Everyone is having the same issue. I like the idea of cutting out the rods. Big time saver. Thanks for sharing this awesome upgrade.

@NeuroticRCshorts 4 ай бұрын

You bet

@Watermoehlen 4 ай бұрын

Finally got my lmt mini after a 3 month back order. Bought a ton of Treal parts for it already just running it stock for a bit before I load it up with aluminum, lol. Good tutorial on the sway bars…I was definitely curious about the sway bar swap and your cutting out is way better than pulling off one side of the frame

@NeuroticRCshorts 4 ай бұрын

Thank you man! You’ll love the lmt!

@FSCreed 4 ай бұрын

I don’t imagine this would last very long

@NeuroticRCshorts 4 ай бұрын

I got several hours on it and and orings on the piston.

@NeuroticRCshorts 4 ай бұрын

Still runs today with no wear marks. It doesn’t heat up at all with the cold air compressor air that’s getting pushed into the engine

@FSCreed 4 ай бұрын

@@NeuroticRCshorts thats awesome, are you planning on creating an entire Lego powered vehicle?

@NeuroticRCshorts 4 ай бұрын

Not sure…

@ellgwapo.1754 4 ай бұрын

That's! On heavy Motor fail That's true.

@user-om5mj9rb8n 4 ай бұрын

I thought it was real😅

@SJJ1776 4 ай бұрын

Did you have to do any upgrades to make it tougher

@NeuroticRCshorts 4 ай бұрын

Bone stock!! I don’t even have the high speed gear on her!

@armorkingg1 5 ай бұрын

Excellent video, thank you for sharing. Looking at some of these myself at the moment. Also, where did you get your shirt? I like it.

@NeuroticRCshorts 5 ай бұрын

Awesome they are definitely worth the money! I can’t remember where the shirt was but it’s just a don’t tread on me shirt!

@martinfield7537 5 ай бұрын

This video said it was instructions on how to bind the HE A3S4 to the satellite but the video never actually showed the binding procedure.

@NeuroticRCshorts 5 ай бұрын

It’s how to bind to a satellite receiver. Satellite receivers give you way more range but have a different binding protocol like a normal receiver.

@martinfield7537 5 ай бұрын

Would you consider doing a video where you show the actual binding with the flashing yellow lights, etc… that’s the step where my radio fails to bind with the satellite even though the gyro and satellite are flashing yellow lights. Thx!

@NeuroticRCshorts 5 ай бұрын

It all depends on what radio you’re using. I use a jumper t lite so I use a different protocol than others. If your using a spectrum satellite receiver just bind it the satellite receiver the same way you’d do without the gyro.

@martinfield7537 5 ай бұрын

Will give it a try, thx

@mosescheng5827 5 ай бұрын

Is this free mod better than the one you buy?

@NeuroticRCshorts 5 ай бұрын

It has the same effect as the lock diff you can buy. So I’d say it is better sense it’s free!

@isaacrudnik2428 5 ай бұрын

It’s incredible what these machines can do keep up the good videos

@NeuroticRCshorts 5 ай бұрын

Thanks, will do!

@Firestrike_09 5 ай бұрын

Yes yes it does

@harlemNYCrc 5 ай бұрын

🔥…..💯

@kevonco_GD 5 ай бұрын

Thats a risky game youre playing my friend

@NeuroticRCshorts 5 ай бұрын

Why?

@kevonco_GD 5 ай бұрын

@@NeuroticRCshorts because lipos don't like water and the way it goes in it's not water tight

@NeuroticRCshorts 5 ай бұрын

It’s a hard case also isn’t submerged in water also is basically completely sealed from dirt and debris. When I was finished it was completely dry. Used the air compressor and completely dried it! No rust for me baby! Just know how to do it right!

@kevonco_GD 5 ай бұрын

Oh I didn't know that

@rb0519 5 ай бұрын

0 they are rolls.

@NeuroticRCshorts 5 ай бұрын

Really?

@GhostBoy7262 5 ай бұрын

2 1/2

@gaminggo-kartswhithnoah8763 5 ай бұрын

6/7

@NeuroticRCshorts 5 ай бұрын

Probably 🤣😂

@thelastonehere8406 5 ай бұрын

😂yeeeeeeeeeeeeessssssssssss😂

@GiovanniSalazar-ni1dz 5 ай бұрын

Noooooo

@Jaydenheheheh 5 ай бұрын

█▄░█ █▀█ █ █░▀█ █▄█ ▄

@Jamisontherider 5 ай бұрын

@Himothythethird-_- 5 ай бұрын

Hmmmm not sped up

@CowboyRc743 5 ай бұрын

I'm waiting on a brown K5, delayed by weather in shipping. I hope it's as cool as their K10.

@NeuroticRCshorts 5 ай бұрын

That sucks just got a lmt mini lucky I got! I bet it will be just as cool!

@mattferrell90 5 ай бұрын

It has just the right amount what are ya talkin about lol

@neoeons29 6 ай бұрын

Is range limited when using a satellite only receiver?

@NeuroticRCshorts 6 ай бұрын

Range on satellite receivers are the best! That’s why I connected it with my a3 super gyro! But no it’s not limited!

@neoeons29 6 ай бұрын

@NeuroticRCshorts nice. I just waited 3 weeks to get the A3 mini and come to find out it won't work with my ar610 receiver so I'm exploring options. Thank you!!

@NeuroticRCshorts 6 ай бұрын

Damn that sucks! I’d definitely recommend a spectrum satellite receiver if you can use it! Please subscribe alsmot at 500!!

@neoeons29 6 ай бұрын

@NeuroticRCshorts ok I just subbed.

@NeuroticRCshorts 6 ай бұрын

Thanks brother!!