Very cool build.. and curious to see how all the motors stack up. I recently upgraded my boat to a ZTW Shark 100A g2 unit. I put 6mm bullets for the battery connection and upgraded the motor bullets from 3.5 to 4mm. I saw a chart that explained what all the different sizes are rated at, so that cleared up a lot of the mystery of "what the hell do I put on here?" 👍🫡

Looking good, looking light weight looking like she will move. Can't wait to see her run! If I may add. The key to running mono's cool as can be.. is reduce drag, reduce drag, reduce drag.. Can't emphasize that enough.. You're almost there setting her up for open class mono racing!! Don't think that's your intent though.. If so, Throw the esc back by the motor SMC HCL HP 6s single pack up front on the tray It won't be the fastest boat in the class. BUT.. The fastest boats don't always win You'll run cool you'll run stable in the chop... And you'd be able to run at wot Great build series!

A 3000kv 4092 will be an amp hungry motor. You will need the castle hydra for that motor. For battery think smc srd cells. I would would say 6200 mah or higher, all depends on what you can fit comfortably on the battery mount. The motor will be amp hungry on 4s, you would have to settle for an abc 1714 to 1716 17 45 2 blade. If you can get say the 8600 mah smc srd cells, you may be able to try the 1814 to 1815 or 1816 17 45 2 blade props. Which would draw 315 to 330amps. Peak amps would be like 380 plus amps, which would drop of to the 315 to 330 when the motor reach peak speed. Ampdraw might be in excess of 250 amps on 4s with the 17 series size props. I can picture speeds of 60 plus on 4s.

Nice job and looks good. on 4S 3000KV will put you at around 60MPH with the 4092 you will have some good prop choices.

All top of the line components installed like it was factory made and great job on the servo mount, these wfly x9 remotes are as good as you can get based on reviews i have seen although i use the Spektrum Pro because of the launch control which is not only good for no prep drag but boats too.

Do you by chance remember what the rudder part # is? Did you have to do any fab to mount it up besides the servo linkage? Looking to build my Impulse more for pond hopping than racing so wanting the extra turning capability I saw in your video.

Thanks for the shout-out, I enjoy watching your building videos too.. keep up the good work! As for the little hydrodoplane I've since Chnged my mind on the side to side weight distribution on a hydro, I like the weight side to side to be perfectly even on each side, (balanced out) Hydroplanes are really flying while your running them and the props you'll be running on that little hull shouldn't torque roll the hull that bad.

Hi i got the same build rigth now ,and have Rocket 2858 4200Kv and the 4489kv and the 2848 4800Kv ,i run a 90 grams ZWR 80A or flycolor 90A/120...3,17 mm Flexshaft ...60mm ligth weigth plastic rudder ...and i use 5,5mm bullets aswell

Wicked video man ,I was going to buy sonic wake 36 but the impulse has just changed my mind , impulse is savage lol

you have any interest in building a gas hydro or outrigger?

Nice looking good

Could you tell me the prop u were running and where you got it?😅

That's awesome. Come to find out my impulse 32 cable is identical to my Delta force......

Here's an idea have a remote sliding battery tray to adjust weight at full speed

Concerns no, but few thoughts... You didnt weigh straps on the non adjustable which makes difference smaller. Also you can skuff of a lot off weight from the adjustable ones. Also you already added unnecessary weight by putting in a layer off carbon. That being said, would put wide simple one in. That should be enough to run 2-4s or one big 4s or 6s. Maybe for this build weight is important, don't know. My dom is far from light now, but have no issues in anyway with it since its a speed setup and it had to be reinforced and also has heavier electronics. It was bit more nimble stock/ reacts bit slower if you will, but thats it.

I have the pursuit which is very similar to your boat, in fact they use some of the same parts. I run 6s in mine and I have the wide simple carbon fiber battery mount. Just one. I've gotten 73 so far and she has more to give. So just wanted to give you that option. Also last video you were disappointed with the paint job. I just painted my pursuit with automotive paint in a can. It's candy apple red. It is excellent paint and dries really fast. The company is called kustom cans, with a "k". Thought you and your viewers might like it.

Good stuff! BG4L🚤💨

This is going to be a good build when completed, I have these carbon TFL sliding trays in my boat and they can be a pain in the ass, although in this hull maybe not as much but in a Cat they limit battery choices because they take up more room and they dont slide as easily as you would want, recommend changing the strap to a bit narrower, the TFL straps blocks the slide causing friction. I am impressed with your workmanship.

Cool stuff you gave me some ideas!!

Word of advice, do not use the MHZ hardware. It’s all metric German spec hardware. I have the MHZ Mystic 114 cat and the stub shaft cannot be found anywhere except MHZ and it cost me $100 to ship to US. I would use standard hardware OSE sells. I’m considering changing my struts just to get standard shafts.

reminds me of the late 90s Budweiser Hydro (red) electric smaller ~ think that will look amazing in the water with the rooster tail

I own six boats and a rescue air boat! Don't listen to those fools that complain about your expensive hobby. They most likely have a $30,000 bass boat in the driveway or an $80,000 Hellcat!

2 2s batteries in the sponsons?

I totally understand about not being able to pull the battery out that's why I made a couple small blocks of wood running the length of my motor mount used really thin l-shaped aluminum and ran four screws through the bottom of the floor . That way I can pull my motor and replace the batteries if need be. Or you can just not use the wood blocks and use the l-shaped aluminum that you can get at Lowe's and both that to the floor that would work perfect to be able to pull the motor out and go back in the same place

If you trim it like you suggest at 10:35...wouldn't that also give you enough room to put the battery in and out over the motor with them arranged like at 8:41?

ZTW 200a g2 + motor tpower 4060 2080kv 189a elice octura M447 voilla proger = A + de 80mhl

I got the same JAE rigger kit! Had it for a couple years now, still building it! How long did it take 2 get the MHZ hull ? Definitely some cool builds coming from your channel!

I have a question on your shrimp rigger, what and how did you finish the outer skin of the rigger? Am I supposed to get some half ounce cloth and resin and cover the entire Rigoberto in cloth How to build up a shell? I’m not sure exactly how to proceed. I’ve got the thing finished. I just don’t know what to do to it to protect all the wood..

Big B is a good teacher and has so much information on his channel. I like the way you put information out there also Keep it up.

Early comments beat me to it dr jet is all about little boats

Hey H2O, Check out DrJets vids, he has a ton of build info on the MHZ hulls, great little boats I may add. He just finished a MHZ T3 build he did that very thing mounting the motor up in the canopy.Cant wait to see them all the builds, my pick is the Zippykits 33, ( Super nice, fast, and stable ) I'm laying up my final seal coat on my second 33 as I type this.I strongly urge you to take a look at Sam Hallstrom's vids on his 33FE build, just to see and hear his ideas. With my first 33FE on the maiden, I was able to get 93.5 MPH out of it in a pond about 1/3 the size of the large pond you run on. Awesome content, when you get the larger Hull, Check out Pill Thomas hulls, there very nice hand layed hulls, I'm getting ready to start mine. I appreciate all the info/videos you and Big b produce, there very informative and are invaluable...... No disrespect at all, Ive been watching your channel for a bit, and feel your perfectly capable of hitting the sweet spot with your 33, I can give you my setup, just food for though.keep up the great work.BGFL

Got 16 inch Hydros for sale American made.. Hull & hardware, kit or ARTR.. Contact me if you're interested The smaller boats are more challenging to build. Considering alot of the internal hardware needs to be custom built. For the small hydro 28mm motor I've built many My email is in my Profile. Great video H20!

Pretty cool projects.. I like your thinking with the hydro. Motor way forward and plenty of room aft for adjustment BG4L🚤💨

Dr Jet has build one of these white hidro...

I thought i saw a gap just then between the drive dog and the strut

I say do all 3 one at a time. Start with the white one!! Just my opinion! Id love to have a rigger on my channel! Hope this helps

Hi, I have a brand new WFLY X9S set, and S01G gps module, but my Tx did not read and say the speed. What do I miss on Tx setting? (the instruction manual was not clear about the setting). Please post the setting instruction. Thank you and have happy boating.

I love your box of props 👌 😂

Always love seeing the shrimp hauling tail across the water. Awesome content, we appreciate it and look forward to the next one.

So great for just 3s must be a good prop.