I have this saw and I'm very disappointed in the workmanship of the machine. Nearly ALL the components that are part of the construction of the machine are all rusted. Cheap components. The wheels wobble and putting on a replacement blade is nearly impossible. They have NO video that actually shows you how to track a replacement blade. The instruction manual does help. However, with all the rusted parts and poor workmanship it is extremely difficult. What they tell you in the manual doesn't exactly translate to successful practical application. Customer service NEVER answers and NEVER returns your calls. I cannot recommend this product.

I have this saw and I'm very disappointed in the workmanship of the machine. Nearly ALL the components that are part of the construction of the machine are all rusted. Cheap components. The wheels wobble and putting on a replacement blade is nearly impossible. They have NO video that actually shows you how to track a replacement blade. The instruction manual does help. However, with all the rusted parts and poor workmanship it is extremely difficult. What they tell you in the manual doesn't exactly translate to successful practical application. Customer service NEVER answers and NEVER returns your calls. I cannot recommend this product.

I wanted to see how to put the bit on, parts that I'm supposed to grease. My grinder is new out of the box. All this showed was how to wet the sponge. 😐

No end result?

Can I soder on any surface? Will it stick, then afterwards, resin the blank spaces

Thanks for the demo. Can you cut circles with the Beetle Bit?

Thank You!

I prefer the Taurus ring saw.

So the Prometheus clay I bought said torch firing will result in compromised bronze. It has to be carbon fired.

Thanks you make it look so easy! If I may ask some advice? I feel like this is a stupid question cos no one ever address it and it’s hard to see from videos when starting score is cutter to be positioned on the outer lip of the outside glass edge or from the edge surface and if the later is correct does the start have to be right on the edge or is it ok to be lil past it? I hope that made sense

Been 30 years since I’ve done copper foil but ready to get back into it …

How long does it stay in that machine?

I started with a Taurus 2 saw twenty years ago; at that time users were advised ONLY to cut at a 45 degree angle (forwards or backwards) - now I see you cutting at all angles but that. Of course the design has obviously been improved, but I want my saw to last - comments?

I know it’s been 11 years…this video needs updating. Not just the products, but someone that can read a script and not ramble

So basically the iridized is sprayed on and dichroic is burned on? Am i understanding that right?

when you reach the 7.07 time mark, the sound goes out...

You wait till the end to get to the thick mats, what is the process to make a mold of that material?

This video shows only straight cuts being made. I would like to see how well it works on different depths of inside cuts.

Mine has NO waterline mark on the machine...?

Can someone tell me what happens if the traditional running pliers don’t come with a middle line? Should I ask for new ones? I’m not new to this kind of crafting, but I’ve received a set that doesn’t and I’ve never used one without before.

This is a great video! What is that board made out of that the thumbtacks are stuck into?

Love seeing this from 13 years ago!

do you mold a mold where I can make jars and not slump them but slump glass to make jars? thanks.

Thank You!!!!!!!!!!!!!!!!

I just LOVE this so much! It's so cute. I have a question. What would you suggest to use if I wanted to make this and be able to hang it? Thank you so much if you see this and answer me!

Is fiberboard just a kiln shelf?

Just bought this

I tried doin that when i dropped solder down yhe channel it hardened before i coukd get the hook down the channel i couldnt get it down . I ended up melting the top of the zinc plus where do you get a 3/16 tip to fit Hakko iron?

Do you ever have a problem with the bar lifting up from the blocks it sits on , on the grid while your cutting?

It’s not came, its zinc--

Can you also cut hexagons and octagons with this?

There's no sound for how to cut a diamond

I would have loved to have seen the result of the sponge dabbing technique. Is it possible to post a picture of it here? Thanks for your instruction😀

Am I crazy or has something changed since this video was made? I'm new to this, and I'm trying to learn, but I purchased the beetle bits system new at the sidewalk sale this year, and it doesn't have the actual cutter anymore correct? Or am I just confused and missing something? 😅

Im having trouble attaching rings My piece has round lead came . I attached rings to it and the live fell

Great video, thank you. It seemed odd though when the presenter talked about safety and then proceeded to cut and sweep up glass without gloves.

Skip to 2:44. At 4 minutes, the slow talking lady will be cut off in the middle of FINALLY setting the temperature. She never gets to explain how to review the existing programs. Perhaps she is still out there somewhere in the year 1998, holding her finger in midair.

You can see what the instructor is doing. Not a helpful video as far as cutting does 😞

I have been creating stained glass pieces for a long time, but I just learned some new techniques! I've always enjoyed using globs for decoration. Can't wait to try these.

excellent information. the cutter design is for the person. they cutting wheel are all the same. Thanks for clarifying that.

Thank you!!! Short and very informative. Keep up the great tutorials!

Would using some flux help prevent the oxide taking off that much of the bronze?

please running plastic pliers does it work on mirror?? THANKS

This is by far the most helpful video I have found on this. Can't thank you enough!

Cuanto cuesta y donde se puede comprar

Followed these instructions to the tee and the glass welded to the mold. Fortunately it was only a small one and it didn't ruin my kiln. Still costly though :/ will definitely be curing it next time.

impracticable because your glass is too small to demonstrate any real scenario.

Quero adquirir este,rolo,de,f

Can you give us info on what bit for drill press please

So how many bottles will one blade cut on average?