Thank you for this. We vastly overloaded the drawer and I could not have dismantled and refitted the drawer without your instructions.

What are the dimensions of base and back boards of the drawer for 60cm cabinet box

Are the adjusments on both sides or just on the the right side ?

Get your local carpenter.........

I have same runner system on my drawer can I upgrade it with soft close one?help pls

Don’t you mean 20mm and 50mm, not 2 and 5mm??

The system does not work when the drawer is full. Doesn't seem to have enough force to close the drawer. Is there an adjustment to increase the closing force?

My draws are shaker and different to this. Not helpful at all

Is there a jig available for this ?

Thank you so much for the explantion and the accent :) !

What is the set square for? And the tape measure? Shown at the start then not used.

This is so helpful and clear! Thanks so much!!!

그거서랍 부속명칭 어케되나요

Hi, thank you for the video, what is the difference between Antaro and Intivo Tandembox ?

put links to the first video in the links please

Our drawers were installed 1988 and now the drawer front wiggles/rocks back and forth at the top and bottom off the side screw- it hasn’t stayed tight to drawer front since we bought the house in 2004. I took the cover off the outside Blum connector and I see no way to fix it. Any idea?

That was a big help to me how to put fronts on the drawers

You completely miss out the fact that the back panel support pieces are no longer fitted when they arrive. You have to work it out entirely for yourself it seems.

Hi. I bought a set, but the supplier only supplied the drawer sides, and runners. They didnt supply the melamine for the drawer box base or rear panel. The cabinet is ade from18mm melamine, and is 500mm wide in total. What width melamine should i be using? Thanks in advance.

I saw the other just lift up. I try mine. But doesn't work. Any idea. thanks

please help my drawer fall out from screw and I need to full back. But the runner and drawer attached. How to remove the runner into drawer. Thank you.

👍👍

👍👍

Thanks for the video. It saved a lot of efforts of the engineer as we never knew how to take that small part out of the drawer to fit in the panel.

Just asking , what is the width of drawer bottom and back panel? How many millimeter do we need to cut from the the total with of a carcase? Let say 900mm with carcase? what is the width of drawer bottom panel?

Great information video to understand which product is best for me. Thanks

Really good instructions. Thank you.

Really good instructions. Thank you.

Thanks for your instructions,very helpful I have some drawers fitted already with these and am trying to figure out what cabinet size I need

Thank uuu...

Do you do jewellery tray drawers?

Thanks for the video. The front of the draw came off on one side (screws loose) so wasn't obvious how to reassemble. Video helped Cheers

today 'metabox' is just the brand new metabo style systainer 😅

Thank you verrry much... Yesterday the front of our drawer Just came out and i couldn't figure out how to fix it until i watch this video... İ Just take it of and fixed it😁😁😁😁

Thanks you for your video.

Thanks you for your video.

Instead relling anything else for drawer pull?

Hi there. Can this formula be used for the drawers hight 150 mm?

Awesome fitted mine in 20mins only thing i did was to put a bracket between the back and base panel as there was a bit of movement (1000mm cabinet) so the 2 didn't separate when pushed or pulled did the same for the front as well underneath. 9/10

thank youuuuu very much,Davorka,sucesfull made

super,hvala

Thank you, short sweet and to the point

Thanks a lot had no idea how to remove these brackets.

Aks

Thank you

Hello bro

ps I have four screw bolts but no instructions where they go????

heartfelt thank you for this down to earth waffle free instruction videos, I could not have done mine without your help,,

Are yar hindhi mne dalon vidio

Ka