Hi, great video!! but my problem doesn"t seem to be a plug may be thermal fuse. Do you know where is that located? I tried to look up but no luck so far..
@Freebird462Күн бұрын
Have you used this for finishing new drywall? If so thoughts?
@buildingwithpapaКүн бұрын
I’ve had power sanders in the past and they were much more expensive. I have to tell you I think this one is really good. I like how it folds up and so far I haven’t had any issues.
@DanceHoops2 күн бұрын
Well done pops.
@buildingwithpapaКүн бұрын
Thank you for your comment and if you can leave me a thumbs up.
@reggiegabriel25453 күн бұрын
Wish I would of found this video before the Harbor freight one!
@buildingwithpapa3 күн бұрын
Thank you for your comment and if you can leave me a thumbs up.
@mrguerra123455 күн бұрын
Are the amplifiers interchangeable?
@buildingwithpapa4 күн бұрын
Thank you for your question but I don’t know if they are interchangeable. I just bought the one that was for my vehicle. I hope this helps you and if you can leave a thumbs up.
@isaacfuentes4458 күн бұрын
You also ordered the hose kit. Did you end up using it at all? Or did the pump have everything you needed?
@buildingwithpapa8 күн бұрын
Thank you for your question. I believe the pump came with everything I needed. I hope this helps you and if you can leave me a thumbs up.
@Slime00168 күн бұрын
Having a lot of trouble @ 2:31 can’t get cap off of mine
@buildingwithpapa8 күн бұрын
Thank you for your comment make sure you’re not turning the cap to the left like you normally would when you’re taking it off it’s a reverse thread. I hope this helps you and if you can leave me a thumbs up.
@DavidCohen-t6p8 күн бұрын
Thank you for doing this video. It was a huge help! My pool robot is back in busy!
@buildingwithpapa8 күн бұрын
Thank you for your comment and if you can leave me a thumbs up.
@lksmith588 күн бұрын
Which do you like better the Dophin or the Polaris?
@buildingwithpapa7 күн бұрын
The dolphin is easier to work on but harder to clean the Polaris is easy to clean, but I don’t know how it is to work on at this point. I hope this helps you and if you can leave me a thumbs up.
@easy196510 күн бұрын
Works the same for Avalanche 2013. I did the driver's side door. On that door remember you will need to take the lock off and put it on the new one. That is also a simple process, the lock is held by a spring bar retention clip that pops right out. Great video, thank you
@buildingwithpapa9 күн бұрын
Thank you for your comment and if you can leave me a thumbs up.
@MooeyMoo10 күн бұрын
Great video!!! Thumbs up
@buildingwithpapa9 күн бұрын
Thank you for your comment.
@CPOGARCIA12 күн бұрын
Thank you for taking the time to make this video. Did everything you did, and my unit is operating flawlessly! You rock! Very much appreciated.
@buildingwithpapa11 күн бұрын
Thank you for your comment and if you can leave me a thumbs up.
@TommyJones4913 күн бұрын
Not moving. Cord was bad. New cord worked fine. Now now working again power supply good 29.5 volts suspect motor are they expensive? How do you test and replace? Unit bought in 2021
@buildingwithpapa11 күн бұрын
I will say if you have your cord is fine you show 29.5 V for the power supply. The only thing really left is telling you we are not liars. They’re not cheap but it’s cheaper than buying a new unit. Make sure all your bearings are free and not bound up that would keep the motor from pushing it, but it does sound like it’s very possibly your motor. I hope this helps you and if you can leave me a thumbs up.
@robertfoster166513 күн бұрын
I can’t get the charger to turn off. There’s some play in the buttton as well.
@buildingwithpapa11 күн бұрын
I haven’t had any trouble with my switch, but it sure sounds like your switches bad you may have to disconnect it and use a tester for continuity test so when you turn the switch on if your meter beeps for continuity, then it’s not your switch if it doesn’t, then it is your switch. I hope this helps you and if you can leave me a thumbs up.
@jctheprohawkins429215 күн бұрын
Thanks !!!
@buildingwithpapa14 күн бұрын
Thank you for your comment and if you can leave me a thumbs up.
@mastababy1216 күн бұрын
Help please. Mine turns on but not heating...do you a fix for that. Thank you
@buildingwithpapa15 күн бұрын
Thank you for your question. Did you go through the diagnostic of finding out if it has power to certain locations it could be your element that is burnt out. I hope this helps you and if you can leave me a thumbs up.
@jerryw445818 күн бұрын
How's this holding up after 3 months? Thanks!
@buildingwithpapa17 күн бұрын
It has been great. I have not had any issues. Are used to get those expandable hoses and had a little Chihuahua that would chew on them and tear them up now my hose is not laying on the ground reels out where I need it and reels back in. I hope this helps you and if you can leave me a thumbs up.
@michaellawson732021 күн бұрын
Any chance you can post the link for the part
@buildingwithpapa20 күн бұрын
It’s called the micro switch. I did put it in the description, but I copied it here for you.www.amazon.com/gp/search?ie=UTF8&tag=papabuilding-20&linkCode=ur2&linkId=ca691ec1b76a1f640c097dc435fb2034&camp=1789&creative=9325&index=appliances&keywords=KW7 I hope this helps you and if you can leave me a thumbs up.
@tmossberg21 күн бұрын
The swivels are going to fail after about two years I didn’t want to spend another $200 on this thing after replacing all the other parts so I took the swivel off and wired directly For $200 I want tangled the cord when I pull it out of the pool
@buildingwithpapa20 күн бұрын
Thank you for the information. I’m glad that works for you and if you can leave me a thumbs up.
@XxZgamexX23 күн бұрын
When I start the car the pump kick in and shocks inflate and then deflate quickly after that. Is this how they are suppose to work?
@buildingwithpapa23 күн бұрын
No, you must have a leak somewhere. I hope this helps you and if you can leave me a thumbs up.
@XxZgamexX22 күн бұрын
@@buildingwithpapa thanks. Will do.
@ar570124 күн бұрын
Preciate you bubs!
@buildingwithpapa24 күн бұрын
Thank you for your comment and if you can leave me a thumbs up.
@RobinSingh24 күн бұрын
thanks for the video!
@buildingwithpapa24 күн бұрын
Thank you for your comment and if you can leave me a thumbs up.
@chippydog225 күн бұрын
Why not just buy a Milwaukee pro press ? If that’s expensive You’ll be impressed
@buildingwithpapa24 күн бұрын
Thank you for your comment. The Milwaukee is very expensive. This progress was inexpensive. It was under $300 and it has worked very well for me. Hope you enjoyed the video and if you can leave me a thumbs up.
@jaytmoon233126 күн бұрын
thank you for this video. the included instructions are not very good
@buildingwithpapa25 күн бұрын
Thank you for your comment and if you can leave me a thumbs up.
@AmenMoto27 күн бұрын
That press is cool No soldering
@buildingwithpapa27 күн бұрын
Yes, I love it. It works great, especially in some pipes where you can’t get the water to stop where there’s a leaky valve you’re able to press on the fitting.
@pattee21728 күн бұрын
What kind of glue do you use?
@buildingwithpapa28 күн бұрын
I use Loctite. It works very good. I’m glad you liked the video. If you can leave me a thumbs up.
@bobmaslanko445028 күн бұрын
Bobmaz this video saved me a lot of money, thank you so much!
@buildingwithpapa28 күн бұрын
I’m glad you like the video if you can leave me a thumbs up
@mrc1062Ай бұрын
Do yourself a favor and remove the engine hoist brackets from in front of the plugs. Be careful tightening the screws back though, only 5 ft lbs. Too tight and you'll crack cast head
@buildingwithpapaАй бұрын
OK, thank you for your comment and if you can leave me a thumbs up.
@johnbarber4254Ай бұрын
You could’ve put with the gap is you could’ve put how many quarts of oil it took
@buildingwithpapaАй бұрын
Thank you for your comment. The reason I did not do that. Are there are different size units and the gap could be different and the oil could be different. This one happened to be a little over a quart of oil because I change the oil filter. Also, I hope this helps you and if you can leave me a thumbs up.
@rodneypardensr5703Ай бұрын
With no instructions,scratches and oil already in it tells me that they sent you a used unit.
@buildingwithpapaАй бұрын
Yeah, I thought so also but I found out that they do put oil in them to test them and then they suck out the oil and there’s usually a little bit of remnant in there the scratches I’m not so sure it works great so I’m happy thank you for your comment and if you can leave me a thumbs up.
@bswins9648Ай бұрын
Thanks for making this follow up video to your original troubleshooting vid. Looks like I need to order some new belts. 👍🏻
@buildingwithpapaАй бұрын
Thank you for your comment and don’t forget in the description. I have the link for buying the belts.
@edgarbiii4661Ай бұрын
Can these be installed on hollow doors?
@buildingwithpapaАй бұрын
They’re designed for solid core doors and fire doors for emergency exits. They would not work well on hollow corridor. I hope this helps you and if you can leave me a thumbs up.
@jcb615Ай бұрын
Thanks for the video. I had this same issue and discovered a bad cable.
@buildingwithpapaАй бұрын
Thank you for your comment and if you can leave me a thumbs up.
@jcb615Ай бұрын
@@buildingwithpapa Done!
@gregarchipow7643Ай бұрын
best one I've seen so far
@buildingwithpapaАй бұрын
Thank you for your comment and if you can leave me a thumbs up.
@AmenMotoАй бұрын
Beautiful
@buildingwithpapaАй бұрын
Thank you for your comment and if you can leave me a thumbs up.
@michelewaters4154Ай бұрын
Thank you for this video. I was able to replace my swivel cord and the side foam that was pretty beaten up with ease . You made this possible
@buildingwithpapaАй бұрын
Thank you for your comment and if you can leave me a thumbs up.
@rrlivesay13Ай бұрын
This was super helpful! Thank you for making this a DIY repair for me, and for it to go so smoothly!
@buildingwithpapaАй бұрын
Thank you for your comment and if you can leave me a thumbs up.
@dwightelliott6073Ай бұрын
Nice job!!! Why did you have to reinstall the original brake battery?
@buildingwithpapaАй бұрын
Thank you for your question. The battery was already installed inside the trailer, but it only operated the lights but was not being charged so I had to run the wire to the battery so that it would be charged off the seven pin. I hope you like the video and if you can leave me a thumbs up.
@user-hr4rj3zz6yАй бұрын
USE A BRAKÈR BAR MY MAN !!!!
@buildingwithpapaАй бұрын
Yes, the breaker bar would’ve definitely helped. I’m 68 and I start to think that I can still do these things without a little help. Hope you like the video and if you can leave me a thumbs up.
@rongray4118Ай бұрын
Santo - the only thing that I would add to your video is that the Hydrometer test would have been great to see for each cell before and after. Blessing to You and thanks for posting your video!
@buildingwithpapaАй бұрын
Yes, I’ve had that comment before and I wish I would have done that. I hope you like the video and if you can leave me a thumbs up.
@user-cw2pe6lf1rАй бұрын
great video, thanks
@buildingwithpapaАй бұрын
Thank you for your comment and if you can leave me a thumbs up.
@idreamaworld7177Ай бұрын
Thank you for the video. Do you have to disconnect the battery before you do this? I read somewhere that you do. Want to make sure I didn't miss a step. Thanks
@buildingwithpapaАй бұрын
Thank you for your question. I did not disconnect my battery and I didn’t have any issues but it’s not a bad thing to do. It won’t hurt anything so you may want to do it but it’s up to you. I hope this helps you and if you can leave me a thumbs up.
@idreamaworld7177Ай бұрын
Thank you
@markeverson5849Ай бұрын
You worked your tail off on that for your friend I hope you appreciate it looks good
@buildingwithpapaАй бұрын
Thank you for your comment and if you can leave me a thumbs up.
@lindseymcconnell4310Ай бұрын
You saved my vacuum!! Thank you!!
@buildingwithpapaАй бұрын
Thank you for your comment and if you can leave me a thumbs up.
@pstoneking3418Ай бұрын
Great video. Too bad those adapters don't come with the generators. Just another way to squeeze another $70 out of us.
@buildingwithpapaАй бұрын
Yes, it’s all about the money.
@pstoneking3418Ай бұрын
It seems ecoflow always has ways to get extra money from of us for adapters we need but aren't included with their units. That's another $70 for the adapter to connect the pro to the generator. You can cgarge from the generators AC Outlet but without all the generators smart features that monitors the battery level. Plus, using the included cable, you are charging with DC to DC, which is more efficient. Actually, ecoflow could have a smart generator connector built into the pro instead of using one of the extra battery port.
@buildingwithpapaАй бұрын
Yes, I was stunned when I realized the cable would not connect to my Delta Pro. It doesn’t make any sense why they would sell you a generator that works with the Delta pro and give you a cable that won’t connect to it that you have to buy an adapter and then the other thing is the cables short if you have your batteries at one end of the garage and you wanna put your generator outside the garage the cables not long enough, I’m glad you enjoyed the video and if you can leave me a thumbs up.
@AmenMotoАй бұрын
Pretty neat.
@buildingwithpapaАй бұрын
Thank you for your comment and if you can leave me a thumbs up.
@erinpompaАй бұрын
Thank you
@buildingwithpapaАй бұрын
Thank you for your comment and if you can leave me a thumbs up.
@bswins9648Ай бұрын
Great start to the daily video goal. Look forward to whatever you decide to post. If you're taking requests, I'm having issue with my Dolphin again...starts and stops...won't climb walls even with new rings...passes the "turn it over on it's back" self test just fine. I rewatched the Dolphin videos you posted prior, but if you have any advice on Dolphin pool cleaners, and/or a good replacement to consider, I would appreciate it. Regardless, I love all your vids. Keep up the great work!
@buildingwithpapaАй бұрын
Thank you for your comment. I was just thinking of putting up another video on my dolphin cleaner. I have to put new tracks on and I’ve had a couple questions that I haven’t had issues with so I’m going to look a little further into my unit so thank you again, and if you can leave me a thumb.
@aGibby305Ай бұрын
Do you have any recommendations on a blinking red light? The bag is empty and the tracks are clear?
@buildingwithpapaАй бұрын
Which unit do you have? I’m not sure what you’re talking about. A red blinking light. Mine doesn’t have any red lights.