Are you accessing this site with a laptop? And what cable connections do I need to connect to my Saturn?
@G_Dubai7 күн бұрын
Hello, i need update PCM lincon continental for last Version. Please tell me what tools i need to buy?
@victor35ma10 күн бұрын
I know this video is 2 yrs..old, is it possible to set up or to use Autel interface JVCI 2 PLUS. in R2R?
@LukasHorst-k7x14 күн бұрын
thanks you...saved my beacon...used Autel pro scanner to accomplish and didnt know I had the equiptment to do it!! great video
@raszamataz4615 күн бұрын
Do you have to reflash a used tccm 04 avalanche, Amazon sells Dorman tccm,s says plug and play
@davidborgesuc423918 күн бұрын
I have a Lauch x-431 i was making the TCM program So i put the brand- New TCM module. And tried to do the first step , the ' READ CHARA- TCM replacemet" And the scanner has throw the code " rutine has been failed , imposible to execute this command"
@elnomamez587322 күн бұрын
I bought an the same engine full with harness and computer, but I'm afraid I won't be able to use it unless the PATS gets disabled is that something that can be done just with the PCM by it's self?
@InsidiousMindz22 күн бұрын
I'm experiencing this so hard. Replaced a crankshaft sensor, coil packs, spark plugs. Explain it to me like I'm stupid, cuz that happens a lot. Vehicle stutters, loss of acceleration and rpms don't climb with gas, thought it might be fuel related but it starts perfect. Idle is a little wonky but i have air intake issues at the same time... Working on it 😬 but my girl bought this car. She needed it. Not to be too personal but she's had some medical issues and i just wanna fix it for her. She's so scared it's going to leave her on the side of the road and I'm exhausting my finances fixing it. Sorry for saying i wasn't going to get too personal and then proceeding to get personal. Any help would be greatly appreciated so i can fix this problem. It's really been hard on her. Many thanks for posting this because it sounds like my issue for sure. Do i need a hub? What's a hub? Lol sorry, not a mechanic. I do the work myself but i know literally nothing until i do it myself. 2009 charger sxt pursuit vehicle, 3.5 V6
@paulstevens317726 күн бұрын
Is there a way to change the VIN? I have a 2009 GC that my kids just bought. Everything is good on it but the ESP and TC lights are on. Code for VIN mismatch in the ABS module. I verified the VIN doesn't match. Hoping to get it fixed for them without spending $986 on a new module.
@mjk967427 күн бұрын
Any opinion on a Stetson Bravo charger/power supply 70 or 100 amp. Do these provide clean and stable power??
@abdullahsaad9019Ай бұрын
How can i get a password to connect online, Will they give me the password with the subscription r2r?
@tcummings0Ай бұрын
For anyone trying this currently - ACDelco has updated their program to fix the issues that he runs into in the video. ALSO - need to go through an Immobilizer relearn to get the truck to start. There are a few options when selecting the immobilizer relearn within ACDelco TechLine there are a few options depending on if you want to program new keys or not. There is an option for a BCM replacement where it retains the old key setup.
@BG-xh5rbАй бұрын
I have a tuned F350 6.7 that needs a new valve body. Question; can I use the free download version of Forscan to update the PCM with the new valve body strategy? Thx
@UhBuddy1976Ай бұрын
What do I do if my 99 Ford F150 does not let me access the parameters reset after I replaced the instrument cluster?
@Rjj2721Ай бұрын
I had a customer with a 2016 buick enclave have this code. Issue ended up being a battery with a dead cell.
@freddiepabonАй бұрын
I want to learn a plug valve on a 2008 Dodge Nitro
@ryantcshopableАй бұрын
Can the programming be done with an autel maxisys
@petruandreascondurachi37182 ай бұрын
Thank you ❤ , in my case i replaced the TCM with another used one , i have to write ip now from what i can understand
@kythuatoto25972 ай бұрын
RLUSV81CDFN002368. Santafe 2015 2.4 thank
@tommymach13012 ай бұрын
Need some help!! Much appreciated so my car was sitting for about a year no battery engine being built fasforward to now I had pats issues finally figured it out and it started running crank no start issue but my key fab with a new battery inside as well as the car. The remote would not control the locking and unlocking of the car and the horn would beep and basically go into panic mode then timing it correctly by pressing the button it would shut off but had no control of locking/unlocking of doors. So today I brought the tpms scanner home I only have one key and stupid me selected reset parameters and then also had selected I believe clear key code thinking it would rectify my issue I was wrong I'm now having a crank no start . How do I go about recoding my only key I have in my possession again? My car is a 2004 mustang mach1 and the pats control is in the instrument cluster. When I saw this video I knew rite away I messed up .. thankyou for your post of this video. And i hope to hear from you thankyou for your time..
@TimSmith-ik2sf2 ай бұрын
If i am replacing an air bag module on a 2020 express it would be the same procedure right?
@XxAnthonyvossxX2 ай бұрын
So weird I’m here trying to figure out a 16 ram with this issue and the picture of the red ram you used is the dealer where I currently work at lol what are the odds
@anthonystone25572 ай бұрын
I have an 06 dts. One of the guys that worked for me swapped the passenger headlight. He did it without pulling bumper and lossemed 3 bolts in fuse box under hood now I have no crank no communication
@robertl.grayjr.nremt-p9942 ай бұрын
What would I need besides this Consult 3+ R2R to program new remote fobs for remote start for. 2024 Frontier Pro4X? The factory kit comes with 2 new remote start fobs and a new hood latch. I have a SnapOn Zeus+ with the Nissan upgrade software (added Nissan and Chrysler OEM access but don’t know yet what all the Nissan access can do)
@akurasan232 ай бұрын
I too am curious as to what vehicles our snap on can do. Were you able to get this resolved?
@heavenleeprincess862 ай бұрын
I have an 08 enclave with no crank no start no com amd gas gauge reads E but is full. When key in on position dash lights up perfect then when put to start all dash lights black out headlights go off and nothing until back in on position. Cannot figure it out have replaced starter, alternator, battery, and the engine was jacked up to replace motor mount. Checked all fuse box pins and fuses and relays have been checked and replaced, cleaned up and fixed wires to starter and back grounds.
@kennshotts56032 ай бұрын
I have one my mechanic says only the Dealer can fix my car. Its a 2011 mkx i will have to junk it now.
@k.hinnant43782 ай бұрын
What could be the problem to your car if it's not going over 30 miles per hour?
@QuavandaLewis2 ай бұрын
My awd went out and now my cruise control doesn't work anymore so I need to bring it to Ford to get it fixed
@user-ym4jh1yh6c3 ай бұрын
so where to buy from
@repairfreak3 ай бұрын
Hello Sam, Why cant I find the Transmission Characterization module in Forscan for my 2010 F-150 with the 6R80 transmission? Its not listed as shown in your video. Thank you for any help you can provide.
@24-7Roadside.Assistance3 ай бұрын
Right to repair without having to get insurance and a locksmith license .
@24-7Roadside.Assistance3 ай бұрын
Right To Repair = F Manufacturer
@nickayivor84323 ай бұрын
KNOWLEDGEABLE, TOOLHUTUSA THANK YOU VERY MUCH FOR SHARING YOUR KNOWLEDGE WITH US 👍 from Nick Ayivor from London England UK 🇬🇧 ⏰️ 22:40PM Good Evening
@keithrankins9633 ай бұрын
Any follow up or link to replace the head light module? Thx
@gruvygraphics99843 ай бұрын
damn NERS cost $300 are your SERIOUS? Might as well take it to the dealer
@Surf_killa3 ай бұрын
Awesome quick tutorial, thank you
@BashiruAdams-wm2os3 ай бұрын
Hi my friend good morning I'm watching from Ghana I have range Rover evoque 2017 I replace the TCM can you help me to program it
@user-hh5bj3tu4k3 ай бұрын
Hi.sir.i install a new valve body in my nissan cube 2010.and .my car only moves very slow...do I need to reserve or re program the trans module.or ecm.thank you.
@Autodoc913 ай бұрын
Thank you for the informative video I just started locksmith less than a year ago an SF Bay area and I already have my vsp I found it really important to have and without it you cannot do anything
@JoesAutoElectric3 ай бұрын
I find it interesting how so many folks see this as a good thing. "Anything they deem" is a very dangerous statement which opens he door to say "EVERYTHING is security related"! Then you are forced to get a VSP, and NASTF can write their own check. It is absolutely a lot of smoke and mirrors. I will say it. This is going to stop ZERO car thefts. All it will do is force criminals to steal cars in a different way. They will increase violent crimes, for sure. Instead of the criminal making a key and driving off, they will now carjack you. Make no mistake, the ones stealing these vehicles are making a lot of money overseas. NASTF is not going to stop them, any more than gun laws stop criminals. So, good job to the folks thinking that the lives of a family are worth less than a POS car. I can't say what I really want to say here, so I will leave it at that. PS I have also realized that my initial thoughts were correct about people who do not work in our industry. The folks I speak to had no idea of any of this happening. A lot of them also said they would like to know how to OPT out of this with their new cars. Another funny thing was that the very fist thing said by most folks was the same. If a thief can't take the car from my driveway, what is stopping him from following me or my wife and taking it by force? Of course we all know that car jacking is not a new sport. However, when you force a criminal into having no other way to get what they want, well...you are now directly contributing to the crime. It really comes down to common sense and reading between the lines. I would not be listening much to those who have the most to gain but, instead to common sense. Before I make any more friends, I will respectfully bow out. Food for though folks.
@josecueva55644 ай бұрын
So what was the fn fix bro ? Describe what was fixed
@ahmedjasim87024 ай бұрын
Thanks...please would explain the procedure steps as i understand ... when replacing used cvt you have to write ip chara which labled on transmission ....when replacing used tcm you have to read ip chara from old tcm befor replacement and write it on new used tcm ...if replace blank tcm you have to program tcm online ...is that wright ? what if lable on tansmission is lost ?
@angelmoreno80004 ай бұрын
Freaking awesome video!!! I am very interested in purchasing a scanner tool like the one you used in the video. Do you have a link for it??
@MrTAGJOB4 ай бұрын
I'm trying to program the airbag module on a 2016 Chevy Express sdm. No success. Can you help its ambulance passenger side with no connection to seat
@albertatrucker3324 ай бұрын
Just bought a laptop with whole bunch of softwares yesterday this will be my first job thanks for the video. It will save me a bunch of time writing the parameters
@ironcladpatriot58294 ай бұрын
I'm selling my Autel KM100 because of all these new burdensome regulations.
@ironcladpatriot58294 ай бұрын
Is it true that they will require a business license, insurance, and a locksmith license to perform immobilizer functions? If that's the case, my tool will be useless because I'm not willing to jump through all those hoops.
@Autodoc913 ай бұрын
Yes $2 million insurance policy is required and the locksmith license and other things
@briankotze574 ай бұрын
Thank you for sharing
@ITS-ME-EVERLY4 ай бұрын
You should get checked out by a Doctor for COPD.
@yoblackdream4 ай бұрын
we need to do this even when the same transmission got repaired ? or not? sorry the bad english, we from brazil :(