I COULD KISS YOU ON THE MOUTH, MWUAH THANK YOU!!!

Hi! I did the connection and thought it worked, but I'm having an issue. The outlet works, but the switch only works when I turn on another switch first. This is a 3-way combo switch with a ground connection. Could this be caused by switching the placement of the two light cables? Thanks!

Thank you! I just did mine!

If I have 3 white wires and 3 black, do I pigtail all of the white and all of the black and then connect them to one of the screws and nothing connected to the bottom screws? Thank you

Hi. Thanks for your video. I have a problem. My outside plugs are powered thru one for. The GFI is controlled via a wall switch from inside a hall closet.i have power to the GFI receptacle however when I reset it the breaker on the panel trips. Is it a bad GFI?

Hello !, I have a mayor problem, I turned off breaker then I instolled two new outlet on and two pandect light on ceiling after all I installed everything and turn on breaker back it work for a few mins. then it cut off by it self but breaker remain on and I checked the line a few time to see what cause it and still I'm confuse what went wrong can anyone be kind help me figure this out please .

Breaker is good not trip and gfci outlet not work or reset no switch connected to it all it shows is red light blinks ones in a while

QUESTION: The bathroom GFCI worked fine for many years. But it recently tripped. The "Power" still works. The "Reset" button is sticking out while the "Test" button is pushed in. But, when I press the "Reset" button to try to make it so the "Reset" button is pushed in again, the "Reset" button will not remain pushed into the wall. I then tried resetting everything at the Circuit Box. But, this didn't solve anything. Do you have any advice? ... Also, as a replacement, should I get the 15 Amp or 20 Amp?

You skipped the part I wanted to see. Thanks.

What in the world was that? Pure nonsense video without any explanation to learn😂😂😂

You just solved my problem! My GFCI outlets were wired through the garbage disposal switch, and I had to turn it on before the outlets would reset. Thanks very much for your video!

Thanks so much! I got to the point where you mentioned the garbage disposal and how it needed power and boom! Problem solved.

Is he saying ‘Three, four years’? Or… thirty four years…

Terrible video, I learned nothing

You are an excellent teacher. It's a gift. Thanks to your detailed explanations my GFCI, and therefore my bathroom outlets, are working again. Thank you very very much for helping us.

I'm only 1.22 minutes into your video and I already know I hit the jackpot when it comes to having a professional and an expert teach me how to solve my problem!

Does a gfi make a noise when it shorts out.? Like a 5sec buzzz… Can’t reset it after resting the breaker… it’s getting power but just can not reset…

Thank you! This video helped me fix outlets in the kitchen that were not working. There were 2 outlets with reset buttons and apparently I had to reset in a specific order. I couldn't tell which outlets were downstream of the others. One other outlet (without a reset) was not working either. But now ALL are working again. Just wish I understood the flow of these damn outlets!

I have power to the GFCI Outlet and the reset button works (green light is on) but none of the downline outlets have power. Thoughts?

What happen to the ground wire on the load

What should i do if i have 2 black, 2 white and a copper ground?

thank you you save my day

To fast slow down the video

How do I contact you? online scheduling is not available

Thank you for your video!!! Super well explained and useful Really appreciate it 😊🙏

Quick question yesterday I replaced a hardwired dishwasher that had a 2 gang box under kitchen cabinets that shut power to the dishwasher so I shut switch confirmed no juice undid the wire nuts removed wire from the dishwasher reattached the wire nuts left switch in off position. Replaced dishwasher got everything looking pretty all connections were made go to flip switch inside cabinets to liven up dishwasher and nothing so I check power into the switch no power check breaker for that circuit it’s on it was labeled kitchen outlets and dishwasher I stuck a plug in tester in all the outlets wired correctly and all are working. No holes were drilled in the process no screws potentially driven into a wire behind a wall. I’m at a loss for what the solution is

I had actually replace a gfci outlet that makes a loud sound when tripped with a plug tester I payed attention to where the wires were at detached the line to wire into the new gfci(with usb plugs and uses pigtails) then wired the ground then when I wired the load I removed the wire nuts on it to attach it using wago 221 lever nuts

I’m completely lost. I ran power to a box for my first switch and then I also ran a three-way wire from that to another switch and from that box regular 14 to wire to my ceiling light fixture. The first box that you showed doesn’t explain about the power, entering the box and the three-way line exiting the box.

Can this be used offgrid for a 12v water pump?

Thank you for your video! I was having issues with my garbage disposal and cannot get the outlet to reset. Once I switched on, I was able to reset it. I appreciate the help!

Mine won't reset. And is blinking constantly. Still works I charge my vacuum all the time. House is 3 years old.

My exterior outlets are gfci and I cannot figure out how to reset it still

Omg, for 3 years I couldn’t use the outlet in my bathroom. Your 6 minute video clear, straight fixed my problem easily! You saved me money and future headaches. Thank you so much for sharing this knowledge 😊

I need your help! Im getting no power from my outdoor outlet and in the breaker box nothing is jumped so i cant reset it. The GFCI is a little bit more modern and dont have the cemter reset/test buttons. What can i do?

Great video, does it have a remote or an online app to control?

Best video.

Apparently not supposed to connect another gfci to the first gfci LOAD.

I SPENT COUPLE OF DAYS trying to figure this out!! I thought might be a short in any of the outlets in that circuit, but NONE! THANKS for helping me learn to determine the LOAD SIDE, and the LINE SIDE!! That's the KEY TO THIS. I switched the wires and BINGO! SHE CLICKED just like she should!! THANKS AGAIN!!

OMG you are awesome ❤

Exactly what I was looking for as well as it is short and simple. 👍

I installed new gfci in bathroom and it worked however I plugged in a small air compressor to install baseboards with nail gun and it won’t work or light up to reset. Did I overload it somehow?

Great video

What would cause the load to always be on no matter the position of the on/off switches

This worked like a charm. Thank you so much.

I have power to my outlet but it still won’t reset. It clicks and turns red when the button is pressed but goes off and no power when button released and no light

No one has been talking about the switch to the appliance having to be turned on in order to be able send power to the outlet then ultimately be able to reset the outlet. You just helped me more than I can say. Thank you!🫱

Thank you so much! As others you have helped you just helped me too! I just donated $5. You rock!

This helped me replace my bedroom outlet with a new decora USB outlet.

i got electrocuted

So. What if u don't know what breaker controls that switch ? How do u find it without turning off all breakers?