S C

Пікірлер

@Kinkydoints 11 күн бұрын

I just came in and found your video , that carb comes off easy unplugging two connectors, then removing the top is easier . the way I did it was pulled those white spring holder things the black covers can be assembled on the motors then clock the choke and throttle plates during assembly , pesky little springs arent they . great work .

@tonydavis4957 21 күн бұрын

100% Man straight out of surgery and fixing stuff

@dannygeremia2085 Ай бұрын

do you have a part number for the stepper motor?

@edavenue9138 Ай бұрын

Can send part number And where You bought please

@williamolliges2622 2 ай бұрын

Mine is having hot start issues, and goes into an overload mode at 50%. This might be the source of my problem and will be my starting point. I’d also throw a clean fuel filter at it if the problem shows up after some hours, you know while you’ve got everything apart, and you’re touching it. Since the Cummins shop wants to charge a $650 3 hour diagnostic fee, we’re on our own out here in KZfaq University Land.

@andrewrogers3694 4 ай бұрын

So glad I saw this video. I run 3 of these units. On the other hand im glad you guys had a good experience with customer service. I didnt unfortunately. The woman i spoke with sad if its below xx degrees you will have to manually choke it.! Im like miss.... its an electronic choke!!!!!! She insisted on me having to manually choke it. I had to get the part number and order mine.

@sc22488 4 ай бұрын

Mine was doing the same thing. Choke stuck in the wide open position. Stepper motor. Good luck

@geraldbattisto5670 4 ай бұрын

Thanks!

@geraldbattisto5670 4 ай бұрын

Wasn't sure where the spring actually went, also was your choke working at all. My choke will go to full choke when starting but doesn't return to open when it started. Stepper motor or possibly control board? Thanks

@anthonythompson69 5 ай бұрын

My one do not go up????😢😢😢

@itrrfan2itrrfan281 6 ай бұрын

Called Westinghouse and talk to a lady about my problem with the choke not working properly. She is sending me a new stepper motor and the control box that it connects to. She said they are in Ohio and was very good to talk to someone I could understand. Great service and didn't take long to connect to the tech!

@itrrfan2itrrfan281 5 ай бұрын

Westinghouse sent me the wrong stepper motor three times. My stepper motor has a 5 pin plug and Westinghouse sends a stepper motor with a 6 pin plug. Sent them photos twice along with the correct part number, but they keep sending the wrong part with the wrong part number. I finally got my soldering iron and heat shrink tubing out and change the plug on the 6 pin to 5 pin. Not real happy with this $1100.00 inverter.

@user-wu7sn7ml7v 7 ай бұрын

Thanks man.My little Massey Ferguson 35 with a Perkins diesel is a sweet machine with a load of power.😅

@juanpagan3295 9 ай бұрын

My hero dude, i got the same problem in a ipower i will replace that part. Thank u.!

@rustyrepairs2565 10 ай бұрын

I really appreciate your effort to show what you did to fix the issue. I'm sure many others will find this very helpful!! Nicely done.

@mcotrucking4 10 ай бұрын

Great video, i took off my carburetor to give it a good cleaning and in the process the wiring going to the throttle stepper motor broke. Where can i find that stepper motor?

@TheUltimate65 11 ай бұрын

its there a valve its opening fore oil going back to the resovare , if yes i have a problem wit it, the stop it up, the lifarms not going down to the ground , when i open the cover then flow the oil out

@justinwalters2264 11 ай бұрын

i have a similar problem but i think it’s the throttle stepper motor starts perfect then does seems the motor isn’t doing anything

@justinwalters2264 11 ай бұрын

dies

@user-mt5je3iz8i Жыл бұрын

Where does that spring go? Good video this happening to my Westinghouse generator right now .

@sc22488 Жыл бұрын

They go on the nipple on the end of that small white bracket that the stepper motor sits over. I tried to send a picture but couldn’t. Pause video when I get ready to put stepper motors back on and zoom in on the white brackets. Still new at videos. Hope it helps

@user-mt5je3iz8i Жыл бұрын

@@sc22488 Thank you

@Mike-pb7jm Жыл бұрын

This happened to my Craftsman (Generac) 2500i. Will see if Craftsman honors their warranty as good as Westinghouse.

@8jmacias Жыл бұрын

Where that spring go I can’t find it anywhere

@richardkawucha1232 Жыл бұрын

Took delivery of my iGen 4000DF on Tuesday. The unit came with the factory fix for the auto choke. I installed a Drainzit (Hon1010) for easier oil changes. Took my time and after a couple hrs. it fired up, first time. Bought this as an emergency power source in storms.

@alanlanghorn9528 Жыл бұрын

Replace all the o rings while out the tube has sit in the pump base to

@richrreeves Жыл бұрын

Any chance there was a part number for that stepper motor kit? I am having the same issue with mine.

@sc22488 Жыл бұрын

There was no part number on the bag Westinghouse sent me, but when I told them the problem they knew exactly what I needed and sent me the stepper motor. I did copy the information on top of the stepper motor which is below. Hope it helps. 24BYJ48 12 V DV 249950 YS:220125

@richrreeves Жыл бұрын

@@sc22488 Thanks I will call Tuesday

@ebptube Жыл бұрын

Very usefull, thank you!

@corbett722 Жыл бұрын

It was my pleasure speaking with you and helping you with your iGen4500 generator. I will be using this video to help other customers when needed.

@rotaxrider 10 ай бұрын

This is the exact generator as the Cummins 4500i. Do you know of others?

@jaybilawchuk2225 9 ай бұрын

Hey bud. How would I get a hold of a charging cord that plugs into the front. I’m wondering if that cord is a charger or a maintainer. There’s not much in regards to whether or not it’s a maintainer for off season.