So great video full of usefull informations, but unfortunately basically no views. What a pity. Seems like to have huge audiency, its not required to give so much informations.
@humbledhands29 күн бұрын
Finally a video that addresses a fluttering needle. Thank you for the detailed video
@merives2263Ай бұрын
Amazing video What would cause an ac system to warm up while driving, but get cold at idle?
@andrewwitchell2708Ай бұрын
Is the thermistor has two wires you might be able to bypass them. They are trickier then regular pressure switches
@richardtaylor6242Ай бұрын
proper charge all new components,hi side won't go over 100psi compressor cycles quickly between 21psi and 41psi
@georgegrieninger87762 ай бұрын
ON A 2017 RAM 3.6LT WITH VARIABLE VALVE COMPRESSOR CAN ONE ACCES THE OIL TO VERIFY HOW MUCH IS IN THE COMPRESSOR AS THE CLUTCH HUB HAD FAILED ON THE OLD ONE AND WE ARE REPLACING THE COMPRESSOR, APPEARS TO NOT HAVE A DRAIN PLUG ON A 7SBH17C? PULL THE VARIABLE VALVE OUT OF THE BODY?
@chrisholmes49412 ай бұрын
Best Big Truck A/C information I have ever seen!!!!WoW
@user-ff8pt2gh5m2 ай бұрын
By far The best A/C instruction I have ever come across.
@heavywrenchkris2 ай бұрын
This video needs more views! Excellent training
@guillermobarbosa61133 ай бұрын
What is the torke spec
@kcheema82655 ай бұрын
Very valuable information thanks
@810Batman6 ай бұрын
19 thousand views, almost 300 likes!!! A few ppl need to off there self...
@briccc4why5187 ай бұрын
I highly recommend if you are spec'ing out a truck you buy it with WABCO/Meritor brakes. Bendix totally sucks. You can't even check the outer pad thickness with this tool. Changing Bendix pads sucks also with their fragile chain system instead of gears, like Wabco. Wabco also has an external indicator so you don't need a tool.
@larryturner87228 ай бұрын
You show the heat transfer going from the engine side of the condenser and out the front of the condenser against the wind.. I thought the air flow came through the condenser coil with the assistance of the fan pulling it through. The air flow should be pulling in from the front of the truck which helps with the transfer of heat when the truck is traveling forward. Am I wrong, or was this just more detail???
@nidak13318 ай бұрын
Nice product explanation, exactly wat I was looking for before purchase, I only wish the flash patterns were shown for a little longer for each and in a simulated orientation.
@angelovalentin40509 ай бұрын
If the pressure 35 low side and high side 300 psi it is normal while on high RPM
@jwash251110 ай бұрын
Torque specs do not populate themselves a stated in your video.
@vicpetrishak770511 ай бұрын
Explaining it clear and concise . When a blue butt connector is used , is it that critical of a voltage drop ? Please explain thermistors , are they able to be easily bypassed ?
@vicpetrishak770511 ай бұрын
As a/c refrigerant passes through an expansion tube or valve it changes liquid to gas as the instructor states . Very well done instructor explanation !
@CJ.A-C Жыл бұрын
just found these videos first class.learned a lot.
@Adrian-yc9yz Жыл бұрын
Just a quick question, how is it that when the refrigerant goes through the expansion valve does it drop in temperature. What causes it to drop in temperature?
@abaiok3656Ай бұрын
The rapid change of pressure
@Hunterr4376 Жыл бұрын
Thanks for the ac videos any links for the tools used
@adrianfoca865 Жыл бұрын
Steer Hub - Torque the spindle nut to 300 ft-lbs. while rotating the hub. DO NOT BACK OFF THE SPINDLE NUT. b. Drive or Trailer hub - Torque the spindle nut to 500 ft-lbs.
@vicpetrishak7705 Жыл бұрын
After the initial tightening of the chamber’s clamp with a hammer tap around the clamp , retighten . 120/23
@vicpetrishak7705 Жыл бұрын
Bendix should manufacture slack adjuster clevis pins with hex formed pin heads . This would be to make sure that the pin is free and easy to turn and lubricate . Place a microphone in the audience . 119/23
@Paderson Жыл бұрын
Trying to do this with a 30/30 brake can, any difference?
@Jonk907 Жыл бұрын
3 years and 13 likes, this guy has a big dip in, why is this even posted?
@ScottYdo Жыл бұрын
👍👍🎯
@truckcaretv8649 Жыл бұрын
Good wark 👍
@waitemc Жыл бұрын
Just had a co. That came apart . They just rolled away as the driver was driving. Dident even hurt the axle.
@truckcaretv8649 Жыл бұрын
Good 👍
@baljindersinghsidhu39592 жыл бұрын
I was looking fkr the same on my phone and can't find anything anywhere just the just part i was able to find.. no torque spec was there.
@JS-jv6rg2 жыл бұрын
This sound like a 2 person job right? How would I apply brake and take vice grips off?
@williams65502 жыл бұрын
Do you have shop air and a blow gun with rubber tip? It doesn't take but a few psi to extend the pushrod. In fact, if you put the new chamber in a vise you can pull it out with your bare hands and clamp it off. It must only be about a 30 pound spring in there.
@slavisanikolic84012 жыл бұрын
You need to work on better audio settings for this video
@ethanbowles57732 жыл бұрын
It never just takes a few minutes
@krazykat16973 жыл бұрын
If I ever find who designed this tool they are getting slapped with a chair.
@mdem14462 жыл бұрын
Does this only work for bendix disc brakes? Wheels on?
@mtndewguy99613 жыл бұрын
Great job Kevin, It's always good to refresh the memory.
@norbacyoshzp3663 жыл бұрын
Thanks ! You save my life!
@Jp-hf2hf3 жыл бұрын
All lies... when this company is going to recall this drums. They Keeps over grooving and broken in more than 2 parts.
@andriipavlyk43083 жыл бұрын
Hi. What about disc brake chamber??
@mikewilson38364 жыл бұрын
Between 500 and 600 ft lbs is the torq and good luck getting the nut off first
@TheModelGuy2 жыл бұрын
That explains why it's not coming off haha. First time seeing these in the fleet and was scratching my head. Normally wheel ends are like 50ft to remove the jam nut
@truckcaretv8649 Жыл бұрын
Very good 👍
@shoptechnician45144 жыл бұрын
got a gorrila for sale?
@shoptechnician45144 жыл бұрын
most places have a/c machines now, and techs get weird looks for pulling oldschool guages out haha. they have their uses though!
@dannyyo79485 жыл бұрын
Hello. What is final torque 360ft pounds?
@nogamez265 жыл бұрын
Front 300 and rear 500
@dannyyo79485 жыл бұрын
@@nogamez26 thanks for the reply. It says it on the adjustment nut 500ftlbs but my smart boss said 350 for rears.