snakeclaw

Пікірлер

@Taw3eyaa 2 күн бұрын

I called the air conditioning company and complained about the weak air coming out of the indoor unit. When they examined it, they found that the fan was dirty, so they used compressed air to remove the dirt from the fan. I noticed that they also blew from the top of the air conditioner fins from the top in order to get the dirt inside the coils out for cleaning.

@MrDonny27 6 күн бұрын

That mfer is hard on 2003 monte carlo

@SuperMouseDV 6 күн бұрын

Thankyou none of stud finders worked reliably

@sansfreewill3843 17 күн бұрын

Love this. The hose and clamp idea is genius!

@kingofmonsters2063 21 күн бұрын

Do u think this kaboat is sea worthy or the heavy duty version

@snakeclaw 21 күн бұрын

I think it's sea worthy. I wouldn't put in a bigger engine than what's rated nor would I abuse it jumping 10 ft swells but normal use, sure

@bryanritts213 29 күн бұрын

how about compressed air?

@snakeclaw 29 күн бұрын

I tried that. What occurs is most of the dust is blown back into the coils where I do not want it. Then it takes a long time and makes a mess to try to get the coils clean. Also it only removes the "easy" dust. It never gets the fan blades surface perfectly clean and the lasting effect is short lived as it gets dirty a few weeks later.

@joannahunt3326 Ай бұрын

OK, everybody keeps showing me stuff but I’m not actually seeing it being done

@darrengarlough5121 Ай бұрын

Oil base will be dull. Water base will shine, but water base will peal over time in the sun. Oil base is the way to go.

@mooseo1588 Ай бұрын

Hi - I loved your video on the BRIS inflatable kayak. I’m trying to decide between the Saturn Heavy-Duty KaBoat and a Bris. I am interested in how these two brands compare in your experience. Thanks in advance for your help!

@snakeclaw Ай бұрын

They are similar but PVC degrades in the sunlight, especially the glue. Most of the bris boats have heat welded seams. The Saturn Triton boats have welded seams also but I do not believe regular kaboats have that. Id definitely go with welded seams. My old Saturn kaboat is coming unglued at the seams. How long of a service life depends on how much sun it sees. Btw...the bris has bigger tubes until you get into the bigger Triton boats. Bigger tubes are definitely better for choppy water. Smaller tubes better for calm water as they have lower wind profile. Thx for watching

@lv99redchocobo37 Ай бұрын

Is it the same for a 1999 Buick century do you know?

@snakeclaw Ай бұрын

I do not know but if it's different it won't be very different. The basics will be the same

@warrensolan8758 Ай бұрын

Did you put the tung oil on over ready seal

@raulpendas Ай бұрын

Would you use only Hope's Tung oil instead of Ready seal? I want to protect my gate and fence. Please reply. Thank you for your attetion to this matter. Raul

@aliaswizard6963 Ай бұрын

Straight to the point instructions well done sir 👍🏽

@Jorlanshinkle 2 ай бұрын

What was the put-in/take out? Love the dude that just pulled out the poison ivy. But you are so right, go wash the oil off and you’ll be good to go.

@erikb89 2 ай бұрын

John…you can do anything solo!!! Great idea!!!

@snakeclaw 2 ай бұрын

Thx! Appreciate that

@travisbelleville7064 2 ай бұрын

I wonder if using a mister would make less of a mess and you could just leave it on all the time. I'll find out tomorrow for you! Also, you mentioned making pencil marks for cuts, I just use a permanent marker on the bottom of the paver, worth a try!

@snakeclaw 2 ай бұрын

I think the mister running all the time would be an issue. I think you might get water in the saw motor rather than on the brick. Also, I kept the water off until I lined up my cut exactly. If I turned on the water too soon it would wash off my cut line. So perhaps you can work around that with your technique. Good luck. Let me know how it went

@xyz2007123 3 ай бұрын

Great video. Thanks

@snakeclaw 3 ай бұрын

Appreciate the comment. You are the first.

@marktapp5408 3 ай бұрын

Very useful review. Thanks for making the video!

@robertgroff2105 4 ай бұрын

I was told to use Bee wax in between the pieces of slate to make it smooth. The reason you use Bee wax is there are no petroleum products in the Bee wax so there would never be a mark on your felt later down the road... Works great...

@snakeclaw 4 ай бұрын

Thx!

@haroldfortner9378 4 ай бұрын

Well, apparently, you really didn’t look at your rack because you got three balls in a row all solids and three times around your rack your hair you have two balls that are in line with each other so you need to look at your rack again it sucks sorry

@snakeclaw 4 ай бұрын

Well apparently I don't have 3 consecutive balls of one suit on the perimeter so I'm clueless as to what you are talking about. You need to go look at the rack again it sucks sorry

@tjlomin1466 4 ай бұрын

You handled it well.

@quentinnailsare.2024 4 ай бұрын

Why do people get so upset the way its right.high and low balls on the end

@snakeclaw 4 ай бұрын

Dunno. People think because they played at the YMCA as a kid or played one tournament at a bar that they know all the rules

@jamesoliver5662 4 ай бұрын

Well done. I think Jim should have pulled harder

@michaeldepow6663 4 ай бұрын

How did you get the pipe in with the coupling on?

@snakeclaw 4 ай бұрын

The pipe is in two pieces. You need to sand that PVC coupler and the pipe well enough to where the coupler will slide easily onto the pipe and not get stuck. You have to use plenty of glue. Goober it up with glue when ready. . Slide coupling in place , rotate it, then lower it, add more glue, pull it up into place. Rotate it. Let it set. You have to do this in five or six seconds so be ready once you apply glue. Practice your move before you glue. You have one shot.

@robinburkey2466 5 ай бұрын

Thankyou Thankyou Thankyou!😊

@Scythe_Voltage 5 ай бұрын

THANK U, had someone try and say it goes in numerical order 😂

@snakeclaw 5 ай бұрын

That's unnecessary and takes too long. Even if you want to do solid-stripe pattern is nearly identical to this. Thx for the comment

@billtmarchi4320 5 ай бұрын

3800 and 3400 engines are in different places.

@TonyPowMC 6 ай бұрын

Your way is not what I see when watching eight ball tournaments I’ve taken photos during a Reyes match

@bigbadjojo4863 6 ай бұрын

Thanks for this video it really helped me, my 1987 G10 is similar but only 2 bolts hold it on; unfortunately, the top bolt was gone. I notice a grinding noise when it was running. I am going to go get it tested now.

@snakeclaw 6 ай бұрын

I had a bolt fall out on my 87 chevy van. It rattled pretty bad. Odd yours only has two bolts. I want to think you have 3 bolts and have two missing

@bigbadjojo4863 6 ай бұрын

Would removing that heater hose help any?

@snakeclaw 6 ай бұрын

No. That hose isn't an obstacle.

@user-qg7ro8zi1m 6 ай бұрын

Can I use a regular magnet

@snakeclaw 6 ай бұрын

Probably won't be strong enough to find screw heads behind that tile. You can try but it's hard enough with rare earth magnets. Let me know what happens if you try

@wallacelarry1813 6 ай бұрын

exactly same situation, I know where studs are but you want to be sure, didnt think of simple magnets, thanx again, since stud sensor cannot read through tile

@snakeclaw 6 ай бұрын

Right on. It works well

@wallacelarry1813 6 ай бұрын

thankyou

@desert4seat 7 ай бұрын

I like that rusty van!

@snakeclaw 6 ай бұрын

Thx!

@brianrottinghaus8432 7 ай бұрын

Your's must be a 3.8. Replaced thermostat in my daughter's '05 Impala 3.4 today it was down under air intake. Very different job. Wish it was as easy as your 3.8.

@BigbossLee702 6 ай бұрын

I know exactly what u mean my bolts kept snapping I had to get it towed to my shop n they said it was a bi... to do he said they had to torch the bolts to melt it and take it out and put back in it returns to the normal thread he said.

@anthonygonzalez7337 7 ай бұрын

Not sure why this was randomly recommended to me lol. This was very informative, however I will say that by the time most people get to something as tedious as actually replacing an entire drain pump, they likely have already checked their filter before hand. If you're craft enough to take apart the entire front panel of a washer machine, you already have checked your filter. Good info though regardless!

@meerkat798 7 ай бұрын

Thankyou! It helped!

@reddman1723 7 ай бұрын

Great instruction and video, there is usually a rhyme or reason to many things and in this world, using stuff eventually there need to be maintenance, just so many other things to look after, liked your reasoning on the pump, my LG is well over 5yrs and I have never did anything maintenance wise, now standing water, got to do something, thanks for your video 😊👌🏽👍🏽,got to get busy, will evaluate pump for restricted flow!

@snakeclaw 7 ай бұрын

Before you did what I did make sure you at least clean out the filter basket first. It just unscrews to access it. You might just have a clog

@HowardLen 7 ай бұрын

Thank you for your video, can I ask what size the engine is, wondering if yours is a 305, thanks

@snakeclaw 7 ай бұрын

Yes, 305. I believe the 350 is exactly the same job

@HowardLen 7 ай бұрын

Thank you

@BobbieGWhiz 8 ай бұрын

Thanks. Why can’t you just flip the washer on its side and access the pump from the bottom instead of going to all the trouble of removing the front housing?

@snakeclaw 8 ай бұрын

I'm not sure. I didn't think of that.

@charleschaimkohl 7 ай бұрын

I'm currently repairing my machine from the bottom. Saved so much work