One tip, you want to get the top end of the reflectix under the edge of the roof - otherwise when it rains the water will get trapped in between it and the pop-up fabric.

that is exactly what i needed thank you.

Washing a Zero-Turn is a big No-No!

What’s the name of the pole . Can’t find it on the sites

I love her southern accent

You should test for ohms not continuity

Exactly what I needed to know - thanks for the video!!

Keep a eye out for leaks on trans or axles seals That’s where the oil leaks out most of the time Replacing axles seals are easy and fill up trans 😊 I just dropped the trans and turned over to drain 😊

What's the name of that tape? Could you drop the link for that tape... I'm asking for a friend.

Can you add additional lights to one junction?

Thanks for the vid.....

Thank u for showing site 22!

Awesome. Tysvm. And ty for showing the multimeter. Most people don't ao for real thst saved me time right there.

Never had that issue before…weird. With those, what they call “torque stop” gaskets, just tighten until it stops moving

You never said if that was the 7.3 amp or the 8.5 amp...

Tiny elements look more like kettle ones .

How would take it out to change?

Hey there! Wanting to do something similar to this with our popup, and have a couple questions. Why did you decide to place the mounting brackets and AC unit in that particular spot? I think personally I’d prefer to have ours on the other side of the camper but wanted to make sure there wasn’t a specific reason the spot you used might be best. Also, have you noticed if the weight of the AC unit pulls the roof out of alignment at all? For our camper, if it is just a little unlevel our door has a hard time opening/closing and don’t want something like this to make that harder. Thanks!

You should be wearing eye protection and a mask due to fumes. Just much safer or mix the lye outside.

???

Exactly what I am thinking here! Great work on this !

Thank you so much for this video. It helped tremendously. God bless you and your family.

Mine just grinds when you try to go forward and doesn't move. Reverse doesn't work... Belt and Pullys look good... Should I check the Transmission fluid?...

You still love beach fishing!

Where did you buy your maverick HD at . I really like the Honda fuel injection motor.

Well done… I’ve been looking at the 2024 HD, you have any comments or knowledge about the Briggs 28 hp EFI engine?

Good info!! Thanks!! FJB!!!

O

enjoy it

Brilliant ideas. Starting on mine tomorrow.

I have a question what’s the max speed for a e120 maxtra??

7:15 in slow motion it is more violent

What do I do I my maxtra e120 has been charging for hours and it’s still dead what do I do??

4:07 you can hear the other pigs scream

Great idea I gotta try that

What size is the live cage by chance??

And the ugly

20w50 for cub Cadet rear end

Absolutely junk

i charged it and the light turns on but it won’t move what do i do

Does the seatbelt have to be in before it will drive or cut ?

Bless you

did it cut down on heat?

Please check other videos before you jump into this

Gum chewing drove me insane 🤣🤣🤣 but still good idea

Have to upgrade that trailer to match the new equipment lol

I just had this happen over the weekend sure enough that's what it was that was aggravating mid cut and had 4 yards left tightened and was good to go but reverse was trash forward steering and speed was shot as well nice video 🎉🎉 the exact same side and other side was tight torqued anyway but yea def a QC issue i had quite a few loose bolts missing bolts fuel line bad fuel pump etc not happy with it but hey it gets the job done now lbs

Yeah just blow it off. Just making rust

I love my Bad Boy HD, but to me its really more work to cut the grass. My gas is usually cut to 3 1/2". The cut is great....BUT it leaves about a 1" strip of uncut grass between blade 1 & 2, and between 2 & 3. There is no adjustment for this as this bade spacing is set by the spindle locations, and the blade length. Correct blades are installed and I also put a brand new set of bades on it. The mower still leaves a strip of uncut grass between blades 1&2 and 2&3. Changing cut height does NOT make and difference. So using this Bad Boy means having to cut twice, since after initial pass, you have to go back and move over a few inches and mow it again. Double the time, double the fuel. After 2 months of this problem, and servce that I had assumed would be mediocre since all Bad Boys are sold at Farm Supply and other such stores in this area, none at a lawn and garden or outdoor equipment dealer. Have tried contacting Bad Boy without success. So I'm back to using a 20 year old JD GX335 with 54" deck that makes a beautiful cut.