2023 ktm 250 sxf is very difficult to install. I gave up. Should be easier to install. I may extend the wire so that I can connect it to the connector in front of the bike.
@trxmoto56633 ай бұрын
Where is the clutch on the bike I just picked one up don’t know a thing about them and there is no clutch replacement videos
@aaronneeley10133 ай бұрын
Foot pegs do not come with 10mm nut
@robtucker8563 ай бұрын
Do you guys have one that is compatible with the dual sports? Like my 2024 Husqvarna FE350S. Thanks!
@MulTfrancis3 ай бұрын
Will this work on a tpi two stroke that has the idle screw mod?
@MulTfrancis3 ай бұрын
Can’t install on TPI bikes? A 2020 ktm 300xcw to be specific
@fuellerr4 ай бұрын
Regardless of the comments below the way he's doing it in this video is right, I have been using a TPS setting tool since 2017 on all 6 KTM's that I have had. Every bike I have checked in America has come set Lean from the factory, the other day I checked my buddy's new 2024 KTM 300SX and it was too rich at 0.50. And if you think with a regular volt meter good luck with that because the TPS sensor is very sensitive you will spend an hour trying to get it right.
@wwilcox27262 ай бұрын
It's funny that according to you they all come lean from the factory, and yet KTM has the tightest calibration spec of all the major brands. Hmmm?
@TeamStruggleBunny2 ай бұрын
How would using a volt meter be any different or more difficult than this tool given you still need to clock the TPS? This tool isn't particularly precise at 2 decimal points so hitting .4 and .5 is easier but not as accurate if that matters.
@wwilcox27262 ай бұрын
@@TeamStruggleBunny you're correct about the 2 decimals and it does matter because the ECU's resolving is much finer (12 bit over 5v = better than 3 decimals) than this tool. Also the imprecision of the TPS setting is a greater issue at small throttle openings than it is for large throttle openings.
@TeamStruggleBunny2 ай бұрын
@@wwilcox2726 Makes sense. I had good luck on my 2015 500 exc with increasing the voltage a tiny amount. It really woke the bike up. I'm wondering if a very mild increase would give more bottom end, carb like feeling, on a TBI bike. Tacomoto suggest this works down low but really leans the bike up in the upper values or revs.
@wwilcox27264 ай бұрын
👎 :-/ That's not the proper method.
@78raarons2 ай бұрын
What is the proper method?
@wwilcox27262 ай бұрын
It's different for each of the displacements 250/350/450/500 and you don't set your rpm to whatever you desire or you may create stalling/dying issues. The cold start is also different for each of the models. And don't confuse "setting" the TPS with "calibrating", because KTM specs to 3 decimal places and usually only a total range of 0.005v which is half the resolution of the device. In addittion for true calibration purposes requires a measuring instrument with 4 decimal places of resolution.@@78raarons
@78raarons2 ай бұрын
@@wwilcox2726 ok, but what's improper about it?
@jonathanfrancoeur53934 ай бұрын
Is it fiting whit 2024 fender?
@Kravch964 ай бұрын
Bro is selling a voltmeter for $250 😂
@wwilcox27262 ай бұрын
A low low low resolution one at that.... 2 decimal places :-/
@ryanstewart15212 ай бұрын
Yeah put it plugs in instead of probing and ruining your connections though
@mbh4x5 ай бұрын
Neato
@phillipwright73265 ай бұрын
Go irp
@jaysoncaramat88545 ай бұрын
hm sir?
@billyp109806 ай бұрын
You mention 250 amd 450 4 stroke. Does it also work on the 350 4 strokes?
@glridge6 ай бұрын
The older tool had a timing notch so you could align timing mark on the stator flywheel . The new tool is flat. How to set timing correctly now?
@skidjs8 ай бұрын
$250! Nope!
@dalvannascimento17898 ай бұрын
Como é o nome da paralama ?
@TheFreerider19879 ай бұрын
Is that the same process and values for both 4 stroke an 2 strokes?
@BERZERKERSV49 ай бұрын
$250 !.. you’re trippin’ !……when the TPS reset can be performed with 2 paper clips and a multimeter… kzfaq.info/get/bejne/qL-mpdWqkrGrmX0.htmlsi=Ct0hFXrulxbtnm56
@terraraptorgaming678110 ай бұрын
What's the branding on the motor stand from?
@brunodekeyser351310 ай бұрын
When you do it this way its only oke, when you also do the tps calibration. When you do it like this without the tps calibration its more off than before. Your ecu wil stil think 0,3800 volt is the zero setting while you have changed it to 0,4000 volt. Great video, butt at the calibration process to it. To have no problems.
@felipegoncalves194611 ай бұрын
Qual a tensão correta para motos 250 4tempos?
@felipegoncalves194611 ай бұрын
Qual a tensão correta para uma ktm excf 250 nas 03 posições?
@Charger1813311 ай бұрын
You guys are great appreciate all the videos you have great customer service. I got my top-end through WMR works with Mike awesome guy. I also bought the TPS tool that you made worked awesome keep the videos coming. can't wait to have you guys due my ecu. Thanks from up here in PA where customer service service doesn't exist
@markilleen402711 ай бұрын
why so blurry can't see
@miscreantt11 ай бұрын
How does this differ from the much cheaper tpstool that also doesn't require using the power up dongle or even taking off the seat?
@booger65man10 ай бұрын
What tool is that?
@JohnHowerton1379 ай бұрын
This uses the bikes voltage Vs. onboard power from the other tool.
@wfodavid Жыл бұрын
Will this fit the 2024 KTM 300 XCW with canbus?
@davidrewis3629 Жыл бұрын
Great guide to installing the beveled washer.
@KG-yc6cl Жыл бұрын
How much space between the tool and the cylinder us acceptable????
@DonRohde Жыл бұрын
Thanks for making this i don't care for the new 2023 start stop set up.
@shazmcgee2008 Жыл бұрын
😃 𝕡𝐫o𝕄o𝔰𝓶
@matteo6926 Жыл бұрын
What size grip donuts should I get for a klx110 ?
@132wildman Жыл бұрын
I don't see these washer s on the clutch diagram?
@bikelife_gus319 Жыл бұрын
Did you leave the rear sprocket stock?
@Andrese4life2 жыл бұрын
So can I replace both with them or only 1
@motogpmotogp72812 жыл бұрын
👌
@riderraider92632 жыл бұрын
Rm 85cc automatico 1.000$ estoy dispuesto a pargar por un hembrague con tapa rekluse.
@OfficialChickenJoe2 жыл бұрын
How did you fit it on your levers? Maybe I’m tired but I couldn’t slide it on my ARC levers, then I tried my dads Stock husky levers and then I tried the 110 lever and it wasn’t wide enough for them. What am I doing wrong 😂
@Shrxmp2 жыл бұрын
anyone know if a 2016 ktm 85 would fit the new 2018 or 2020 plastics???
@dylanmcdonough75102 жыл бұрын
Where did you get graphics
@dylanmcdonough75102 жыл бұрын
Where did you get plastics
@dylanlevy21072 жыл бұрын
Bro it's a factory bike lol...
@gavinj.65322 жыл бұрын
@@dylanlevy2107 no it’s not 😂
@paulgalarza58332 жыл бұрын
Great product !!!! Must have in your track toolbox !!!!
@roczendrake96252 жыл бұрын
Supported my brother for years such an awsome family company 💯
@poyorudo3 жыл бұрын
Would this work on a Husaberg fe 390 2010????
@TheSnowboarderJake3 жыл бұрын
Why do they build it like that in the first place?? First time I took the air filter and cage apart I thought it must be the wrong part. This design is intensely confusing.
@edjohnson5533 жыл бұрын
OK, so where the 2-stroke tutorial that you mentioned? Don't see one of those anywhere.Thanks.