Is it strong enough to clean solar panel in 10-20 m up ! ?
@nel34257 күн бұрын
Thank you very much 😅
@georginarogers69668 күн бұрын
Hi! Can I ask. My husband is getting dirty water even though the filters and resin have been changed. Emptied water from tank in van. Would you know a reason? Any helped would be greatly appreciated
@WCSkills7 күн бұрын
Hi, to answer that I would need more info. What system? How many filters and what kind of filters? Were the filters bought recently or have they been sitting stored somewhere for some time (DI resin has a shelf life)
@PedroKarsan9 күн бұрын
I have the same resin vessel filled from brand new. I am not sure how to use it. I attached hose water pipe on one end and a hose spray from the other but there is no water coming out. how long does it take for the water to come out or am i doing something wrong?
@WCSkills9 күн бұрын
@@PedroKarsan There is an input side and an output side. The water has to go through the input side, from the water passes through the resin, fills the tank, pressurizes and the pushes the water up through the riser tube to the output fitting. I don’t believe it’ll work if it goes in the opposite direction. If you have confirmed you are going in the input and still not working, may I ask if you have any kind of shutoff valve installed that may be in the “off” position? Outside of that, I’d put a call in with where you tank for more trouble shooting.
@PedroKarsan9 күн бұрын
@@WCSkills I put the hose coming from the tap to the vessel where it says “IN” and a shower hose where it says “out” so I think I have that part right at least. When you say the water passes through the resin, fills the tank. pressurizes and pushes the water up. I imagine this would take some time and wouldn’t be that quick? How long would this normally take?
@PedroKarsan8 күн бұрын
@@WCSkills I also don’t have any shutoff valve. I was pretty bummed out that it didn’t work as expected
@bluelightning082011 күн бұрын
where can i get the stl or 3mf file for this? Thanks
@symplemynd5711 күн бұрын
I always seem to get my screens too tight and hour glassing the frames.
@WCSkills11 күн бұрын
@@symplemynd57 please watch my other screen repair video from a few years ago, it addresses this issue. kzfaq.info/get/bejne/r9ukrZmGl9rTpJs.htmlsi=O5hJTSB0oOYzDxQW
@garylynn285712 күн бұрын
Always redid mine on a table. But this method is great especially if door is sliding fine. However me I will still do in a table just because of my knee surgeries making it hard for me to get to bottom part door.
@WCSkills12 күн бұрын
Whatever works best. I have bad knees as well
@Bons_Eye12 күн бұрын
This is way easier than taking the whole screen frame out. Thanks so very much for sharing this. I'm on my 5th patio screen replacement due to a squirrel break in, or shall I say chew in. 😒
@WCSkills12 күн бұрын
Glad you found it helpful! I heard that if you sprinkle some black pepper and cayenne pepper around the the bottom of the door/window, the squirrels don't like it. Worth a shot!
@diamondgreenchoreoqueen12 күн бұрын
I need this tshirt! My name is Diamond
@WCSkills12 күн бұрын
@@diamondgreenchoreoqueen 😀
@diamondgreenchoreoqueen12 күн бұрын
Where can I get one❤
@gibson599913 күн бұрын
Anyone know how to recharge resin so you can use it again?
@lemurdreamur925713 күн бұрын
I have a really dumb and somewhat unrelated question. I'm almost embarrassed to ask.. how do I best remove the jets?
@WCSkills13 күн бұрын
@@lemurdreamur9257 I’m guessing you want to switch from pencil jets to fan jets? Removing jets isn’t an easy process. They are wedged in due to them being “barbed” in shape. They go in much easier than they come out. Also, if you do get them out, you end up having a slightly larger hole and the new jets may not fit in snuggly. If you’re wanting more water on the glass, I’d look at adding a rinse bar or adding jets (if there’s existing holes for that) or making a new set of holes to say, change your brush from a 2 jetted to a 4 jetted. I hope I’ve answered your question.
@kenneththomas270613 күн бұрын
The hold downs, so obvious and simple, thank you
@iamwhodis14 күн бұрын
Some jobs near the bay have 400+. I always check well water. If it is over 300 I turn the water way down and hurry my ass up.
@willanderson859614 күн бұрын
The timing of that phone call is great😂
@willanderson859614 күн бұрын
I love you mark
@mrpunx15 күн бұрын
I never found that the top slot worked well for me, but i never did it on higher pulling only by hand but i will try it later this week on a weekly regular job thats 4 sections high.
@fer45soares16 күн бұрын
Enviar para o Brasil?
@marthahubbard946318 күн бұрын
Dawn Powerwash is the best for cleaning everything in my opinion with a scrubber and squeegee. Great video
@Utubin21 күн бұрын
Thank you
@jordangodden88221 күн бұрын
I assume it only holds Moremen channels?
@WCSkills21 күн бұрын
Moerman excelerator handles hold Moerman Liquidator channels, Unger S channels, and not 100% but many use brass channels as well. I’m sure if you search for Moerman handle and brass channels you’ll find some videos on it.
@jeffmcgavic379821 күн бұрын
Thanks so much for the video. I got a few good tips from this.
@Partsunknown42623 күн бұрын
TDS alone doesn't mean water is safe to drink.
@Preciouspink24 күн бұрын
Dead powdery paint from the sash getting on the glass is a pain.
I recently bought an Eco Cart water fed pole system from Mark and it is awesome. I’ve done 30’ glass with no problems and it can go higher. Well worth the investment.
@WCSkillsАй бұрын
Awesome, great to hear!. Thanks for your feedback.
@abraxas511Ай бұрын
You still did it wrong. You are spooling the tape on backwards. If you flip it around, it will roll on, you dont have to use fingers to place it where you want it. It spins off the spool and onto the pipe. Try it, it just rolls right on.
@LaughinLoneStarАй бұрын
Should last at least a couple of weeks ;)
@Dyan92Ай бұрын
Why would videos straight to the point content.
@sprytnaexteriorcleaning6163Ай бұрын
Can we see it clean an actual dirty screen?
@oldschool9622Ай бұрын
A couple questions for ya. I have 15screens to do...so conserving screen material will help in cost savings. Is the window replacement screen directional...meaning does it look/reflect different if material installed in one direction, next screen is rotated 90 to save on replacement stock (screen)? Last question, to help in preventing wrinkles, is it ok to install long side first, then go to opposite side.....finishing shorter ends last? Thanks for any help offered. Great video by the way.
@WCSkillsАй бұрын
@@oldschool9622 unless it’s some special designed screen, direction won’t matter. As far as doing long sides first, you could try one and see how it cones out. I can’t say for certain. Partly depends on screen frame integrity.
@oldschool9622Ай бұрын
@@WCSkills Thank you
@familurstrangers5307Ай бұрын
well, ive come across the holy grail of screen repair videos. this one is by far the best
@fondy44Ай бұрын
Thanks for the review. Not a pro but a janitor in a leased building whose windows are neglected by the owner. Picked up one of these and the Unger T-bar from HD. Sounds like I could have done a lot worse.
@BrandonBuilds-pf1hzАй бұрын
you still got those two gutter tools in stock?
@BrandonBuilds-pf1hzАй бұрын
do those levelers not have spurs?
@WCSkillsАй бұрын
no
@BrandonBuilds-pf1hzАй бұрын
@@WCSkills is that unsafe?
@BrandonBuilds-pf1hzАй бұрын
you still have these in stock?
@WCSkillsАй бұрын
yes I do.
@BrandonBuilds-pf1hzАй бұрын
is that aluminum?
@WCSkillsАй бұрын
It was
@ginarodriguez8876Ай бұрын
Thank you
@SupremeSkepticАй бұрын
does it cause streaks?
@brettkeeler4992Ай бұрын
Great video as you've already read 100 times. Question regarding building new frames... As you know, new frame material bows out to allow for tightening of the mesh. Do you have any recommendations how to accommodate for that to get straight frames when done? I'd assume prerolling the screen into the channel wouldn't be recommended since you would be following the outward bow of the frame? Maybe I'm overthinking it, but figured I'd ask. Thanks!
@WCSkillsАй бұрын
@@brettkeeler4992 sometimes I will pin the 4 corners as in this video but also in the middle as well, so it pulls in the bowing a bit, but not 100%. It also depends on the screen frame manufacturer and how strong their rails are.
@brettkeeler4992Ай бұрын
@@WCSkills Got it, that make sense! Thank you. Do you mind sharing what framing materials you get and from where? I been using a good source at about $0.60/ft in bulk, but I'm always looking out for other options for good quality and price.
@MerchantsOfMiseryАй бұрын
This thing is *terrible* compared to the Excelerator 2.0 + FLIQ. One of the few Moerman products that is no bueno.
@kumuppins95Ай бұрын
superb demo. thanks!
@ChrisHorton007Ай бұрын
Hi, thanks so much for your video. It is really helpful.
@walleyvideo8297Ай бұрын
I like the trip on the 4 small pieces to temporarily hold the mesh in place.
@TheTruthseeker707Ай бұрын
Thanks, now I know. I am trucker and semi trucks have these.
@richardbedard12452 ай бұрын
I'm doing a screen door for the first time. I followed the instructions on the package. It sagged in the middle. This is when I searched for help, and I found your explanation. Made perfect sense to me. Thank you!
@WCSkills2 ай бұрын
You got this!
@Tatedoublespicedaddy2 ай бұрын
Very good video explanation, first time changing mine out and you helped me so much. Thank you!
@padude1312 ай бұрын
You mean I don't need to spend a bunch of money on window cleaners, micro fiber towels, clay bars, steel wool, and whatever else the professionals use?!! Just a rag, some dish soap and water, and a squeegee? Sounds pretty simple! I've also used a window cleaner and newspaper. Works good too.