Plus, if one light is out, will that stop the rest of the lights from working? Thanks so much!
@twowheelwerkz81023 күн бұрын
@@rahnellmonroe5608 no you can have 1 single burnt bulb but the rest will still work. If they are all out it could be your dimmer switch or the solder joints like mentioned in this video.
@rahnellmonroe560823 күн бұрын
@@twowheelwerkz810 Thank you! I was wondering! I was thinking maybe I'll just bypass the dimmer switch. Is that possible?
@rahnellmonroe560825 күн бұрын
Thanks for the video! What would you check if the cluster lights are not working?
@shineylaveena2880Ай бұрын
Is this similar to McLaren Atlas?
@IvyRosethebusАй бұрын
Brilliant! I just finished mine and it works! I can’t thank you enough!
@twowheelwerkz810Ай бұрын
Glad to hear it helped you out. Thanks for watching.
@IvyRosethebusАй бұрын
Excellent! Thank you
@jasonbirch11822 ай бұрын
Can you tell me what the turn signal bulbs use so i can get them on hand before taking it apart? 2002 3000re. Right ts is bad and intermittent tach/speedo.
@VintageSupportServices7 ай бұрын
Do you have any info for the MT940 dash, and MT941 data logger?
@johnhumphreys973210 ай бұрын
That’s awesome. What’s the cost to have that done?
@CartwrightExcavation Жыл бұрын
Awesome video thank you!
@twowheelwerkz810 Жыл бұрын
Glad it helped out thanks for watching.
@davidmorin8576 Жыл бұрын
I'll try it on my non working cluster. Thanks for your video!
@philipkeiser44422 жыл бұрын
This fixed my cluster except for the oil pressure gauge it stays at 50. It was working before the failure. I took the dash out again and re-soldered the connector. Anything I can check at the gauge ?
@twowheelwerkz8102 жыл бұрын
Have you checked the sending unit on the engine? Might also look closely at all the solder joints at the ends of the traces for the oil pressure gauge on the circuit board.
@philipkeiser44422 жыл бұрын
@@twowheelwerkz810 The re-soldering fixed it working now. I used dielectric grease on the pins of the gauges helped with installing the board . Thanks for the video.
@03godzilla282 жыл бұрын
Can you do a video on fixing the fuel guage
@twowheelwerkz8102 жыл бұрын
If your fuel gauge is staying “full” at the time, changing the sending unit will solve your issue.
@guillermobarba24002 жыл бұрын
Do you know how can I change the graphs from distance in "radians" to distance in "meters"?? Thank you for the video!
@twowheelwerkz8102 жыл бұрын
Unfortunately I used wintax for drag racing application so never messed with changing any of that.
@quicktipsandtutorials91832 жыл бұрын
Great video. The solder on this, like many automotive solder joints that fail, is likely due to the solder being too brittle. When you reflow, using solder rated for high vibration environments will often give you a repair that lasts longer than factory new. Again, great info you've set out here.
@alhernandez14752 жыл бұрын
Thank you for the video!
@twowheelwerkz8102 жыл бұрын
No problem, hope it helped. Thanks for watching
@chuckgemme67332 жыл бұрын
Awesome! How’s the truck coming along
@pattersonexcavating2 жыл бұрын
Great Video!! Thanks for the help!!
@twowheelwerkz8102 жыл бұрын
Thanks for watching & glad it helped out.
@ateabaxter6422 жыл бұрын
Have you ever had to test the gauge its self if the soldering does not solve the issue? The Temp gauge in my cluster has not been working, wanting to be able to test the gauge to see if that might be the issue.
@twowheelwerkz8102 жыл бұрын
Most temperature gauges work off of resistance on a ground circuit. So depending on if your gauge is staying all the at the bottom or all the way to the top, you should be able to test your gauge by the following methods. If it is staying at the bottom you can test it by removing the connector from the temp sensor and putting a jumper between the 2 wires, this should peg the gauge at full hot, if the sensor has a single wire you should be able to ground it on your engine & this should also peg the gauge full hot. If your gauge is already pegged full hot before disconnecting the sensor you more than likely have a wire that is grounded out somewhere. Hope this helps with your question, thanks for watching.
@joiescazchen89342 жыл бұрын
how to put the data from witnax into racerender ?
@twowheelwerkz8102 жыл бұрын
Unfortunately I have never used racerender so I will not be of any help with that. Have you tried saving your log file, then opening it up in racerender?
@ttgallardo19972 жыл бұрын
I need help with mine. Can you help me please. You got a phone number?
@twowheelwerkz8102 жыл бұрын
What kind of help are you needing? Send me an email [email protected] explaining your issues & I will do my best to walk you through it.
@dieselboybc2 жыл бұрын
Great walk thru. Looking forward to more content from you. Lets get you to 1000 subscribers.
@DavePR3 жыл бұрын
Man, thank you so much!
@twowheelwerkz8103 жыл бұрын
No problem, glad it helped out!
@1HSYURIDIA3 жыл бұрын
Can i fix same way on newer inter 2003 2004? Cluster?
@twowheelwerkz8103 жыл бұрын
If it is having similar issues it is more than likely worth a try. Never messed with any newer clusters.
@1HSYURIDIA3 жыл бұрын
@@twowheelwerkz810 My does no lights some gages i did replace the bulb lighf but still no light and other gages light went out after i only tryed replace bulb light as well as speedometer not detenting the progatmed speed limit. Already set at 65mph Truck still runs over 80mph?
@1HSYURIDIA3 жыл бұрын
@@twowheelwerkz810 Only 2003 model And no light on most on gages and i did replace bulb light
@twowheelwerkz8103 жыл бұрын
I would definitely give it a try, not much to loose.
@bmc81203 жыл бұрын
Endless possibilities.... Mad scientist
@duce72373 жыл бұрын
When did you get so old? I'm going to have to start calling you gramps
@ErikHerman3 жыл бұрын
Great video. It's obvious that you care about your work. The cluster for the Physics Bus has been out for a while. I resoldered the connections and now when I put it back in the turn signals are all wonky and it won't pass inspection. Do you think I bumped something? Could a solder bridge have caused this? Won't the turn signals work fine even if you drive it around with the whole cluster is unplugged?
@twowheelwerkz8103 жыл бұрын
It seems that the blinkers will not function with the gauge cluster removed, so something in the dash completes the turn signal circuit. With that being said I would assume you either bumped something loose while you had it out or you possible bridged 2 of your solder joints. Might try looking at them under magnifying glass.
@twowheelwerkz8103 жыл бұрын
If you dont feel confident enough to attempt this repair after watching the video, please feel free to reach out & we can handle this repair for you if needed.
@nickbartell44802 жыл бұрын
How much does it cost
@twowheelwerkz8102 жыл бұрын
@@nickbartell4480 I will repair & ship the dash back for 175.00
@982berti2 жыл бұрын
Hi, I have a 2004 9200i and the speedo acts weird. It works properly most of the times but sometimes the needle drops 5-15 mph while accelerating. No big deal when I’m on throttle but it does the same thing when I’m on cruise control. And when it happens, the truck starts to speed up because it thinks it’s slowing down. Keeps accelerating till I turn off the CC and the needle goes up and shows the correct speed again. Speed sensor already changed, wiring from speed sensor to ECM is already inpected, it looks good. Do you know what could be the problem?
@twowheelwerkz8102 жыл бұрын
@@982berti I have never messed with the dashes on the newer trucks. Might be worth taking a look at the solder joints with a magnifying glass.
@janivianroyal15982 жыл бұрын
Do you still woron clusters
@wongkeen13365 жыл бұрын
could you please tell me how to download the WinTAX 4 4.52.02 software? please send me the download link to my email: [email protected]