KEEP ENGINE SPEED OVER 2000 rpm, (2200 PREFERRED), TO GET MAX HP AND A 540 RPM PTO SPEED! Top link set wrong, (too tight),. Use lower gear on tractor so more HP goes to PTO. Higher blade speed closer to the ground creates a vacuum underneath that pulls the long weeds up into the blades so they can be cut instead of only bending them over as yours was doing. You have some great equipment that should last a vary long time; so spend a little time watching some more videos on how other people do it so you can get the maximum performance out of what you have.
@sergeroitman50172 жыл бұрын
nice toy tractor, but not enough muscle for the huge job
@kaseycasece13403 жыл бұрын
WITH THE BOX BLADE SCARIFIRES , U CAN MAKE 2 PASS U WILL BE DONE WITH YOUR DITCH / U HAVE TO ANGLE YOUR BOX BLADE AN DROP ONE OF YOUR SCARIFIRES DOWN IN TO THE GROUND JUST ALITTLE BIT TO DO ANY DITCH WORK !
@kaseycasece13403 жыл бұрын
U DID ALL MOST THE RIGHT WAY DIGGIING DITCH , { ALL MOST } ? ANGLE BOX BLADE DROP OUTSIDE SCARIFIRES DOWN START DIGGING THE DITCH , U WILL HAVE ALL MOST PERFECT DITCH EVERY TIME B U T WAY U ARE TRYING DOING THIS WITH LOADER BUCKET FIRST IS COMPLETE WRONG / LIKE I SAID USE BOX BLADE WITH SCARIFIRES
@captmark883 жыл бұрын
I'd hit it with brush hog. And keep on it regularly to starve out the roots.
@k6outdoors4 жыл бұрын
Much better than a shovel! Good stuff.. feel free to follow me along at K6 Outdoors, if you need some more tractor therapy! Tractor on!
@monkeyrider44804 жыл бұрын
Lol u can just back scrape or do one big sweep and not little passes
@brianhay40244 жыл бұрын
Would have ben nice to know tractor model,
@henriqueroque37013 жыл бұрын
3038E
@lightning75824 жыл бұрын
Protect your hearing sir!
@shanes.34134 жыл бұрын
how much horespower, im looking at the 3025 e or the size above tht and im stumped on which route to go and any info be very much appreciated ?
@not88me4 жыл бұрын
This is a 3038E. Whether the 3025E is adequate for you or not depends on what you are going to do with it. I can say that my tractor does not really have enough weight to make use of that much hp when pulling, e.g. a disk harrow or box blade, at least in my soils. If you are doing heavy PTO work, like mowing heavy grass or weeds, you will do it faster with more hp. Loading manure from a horse barn, doesn't matter so much. For me, it came down to this: no one ever complains that they have too much hp, and the price differential between a 3032E and 3038E was only a few hundred $$, so I went bigger. My buddy has the 3032E, and it works great loading manure and mowing his horse pasture. YMMV, HTH.
@chrisjones91154 жыл бұрын
Great video , great advice and great job!
@TheGogobutt4 жыл бұрын
I have this same setup JD 3032e(32hp) Yanmar 60" rotary cutter and I cut brush and Brazilian pepper trees even taller than this. The tractor pushes right through it and never bogs. The 3025 has 25 engine HP and has a little trouble and needs to be operated slower. Overall i'm very very impressed with this mid sized John Deere.
@73leo734 жыл бұрын
Have you tried the piranha tooth bar!
@arturocastanedajr.63704 жыл бұрын
Worst camera person ever.
@joebarrett98304 жыл бұрын
I thought for sure you were going to bend or pull a cylinder out while trying to dig with the bucket. Glad it went well for you.
@travisricks34365 жыл бұрын
If we lived close to each other I’d let you borrow my Bush Hog...killing me with this! Lol
@EdBlack-4 жыл бұрын
Lmao I was thinking the same thing..over here combing those branch’s, stripping leaves off.. just drive over it and let the bush hog rip it up.
@Boodieman725 жыл бұрын
Doesn't the brush cutter deck float along the ground? Seems to not be keeping level.
@gregwalker7315 жыл бұрын
Too much hog for the tractor
@Kybucks105 жыл бұрын
When he’s on the tractor, watch the video at 2X playback speed. Thank me later.
@subjectofgov3 жыл бұрын
Thank you.
@scummy6660075 жыл бұрын
Would a subsoiler of been efficient in this case? Elec conduit right?
@JustinGH5955 жыл бұрын
Link for the toothbar?
@clinthemphill5 жыл бұрын
Are you happy with this unit?? Comparing to the TSC one (county line) I believe and not sure which way to go....
@Malledeus865 жыл бұрын
Box blade is my favorite implement
@edsonprotazio23196 жыл бұрын
MY GOOD!!!!!
@bennyrlove6 жыл бұрын
brush like that has TICKS!
@dianabarr73896 жыл бұрын
nice job with tractor. I recently bought me John Deere 3025e. these are good little tractors. that front end loader is so handy. don't know how I ever got along without one.💪👍👍👍
@semco720576 жыл бұрын
That tractor is getting the job done and I have two John Deere tractors and love them both, and what they can do.
@user-tw2ex6ub1w6 жыл бұрын
kingoshokai.com
@idahomike1006 жыл бұрын
How long would it take to clear 20 acres
@joehutto12735 жыл бұрын
idahomike100 at this dude's rate, about 6yrs. LMAO
@jimdodge57662 жыл бұрын
At this rate probably a lifetime.
@TheSoloAsylum6 жыл бұрын
Raise the front of the deck and lower the back. That wheel should be on the ground and pressure on the top lint should be about nothing...we have even run without a top link at all, the mower deck floats...
@tomkeating656 жыл бұрын
Clueless in what state?
@deanbarr57406 жыл бұрын
Nice tractor work.
@rkwill1006 жыл бұрын
the tail wheel is set too high there needs to be a flexible connection to the top connection of the three point so the brush hog can float over uneven ground without rocking the tractor
@cpaulpsy6 жыл бұрын
Use s chain for the top link. It allows the deck to float.
@claudiogoncalve83276 жыл бұрын
Um ótima máquina para fazenda
@panama-canada6 жыл бұрын
On my 150 acres you'll be working for a month like that.
@not88me6 жыл бұрын
If I had 150 acres to clear, I wouldn't be using a 30hp compact utility tractor....
@danfrazier83876 жыл бұрын
Why not a 6ft cutter? Buy a Deere cause that Frontier crap is garbage.
@semco720577 жыл бұрын
People at the dealership told me that I could cut brush up to 3" inches in width, but I have cut some up to about one and one half inch in width. One guy clearing an area along the electric lines did cut some brush with his tractor and brush hog up to 3 inches and had no problem.
@hornett223 жыл бұрын
Depends what they're rated for. Light or "standard" duty or usually rated up to 1 1/2 - 2 inches. More than that they'll take quite a beating. The metal just isn't as thick.
@bigscout15847 жыл бұрын
You can also back up over some of the stuff as well, keeps you from having to 'duck' the branches
@bigscout15847 жыл бұрын
Don't know if you intended to do it that way but a word of advice, loosen your top buckle and let the back of the brush hog ride on the wheel, it will be less stressful on the PTO and motor
@usmcpatriot41376 жыл бұрын
Ray Vandegrift I thought you meant his belt buckle
@Berol20007 жыл бұрын
Brush? That looked mostly like trees to me...
@southernoutdoors46717 жыл бұрын
Do you burn your brush
@not88me7 жыл бұрын
No. This is in Florida, wood decays pretty fast. I just pile it and let nature take its course.
@southernoutdoors46717 жыл бұрын
+not88me o ok I'm from Alabama we do alot of burning
@nav34347 жыл бұрын
Cool those teeth on the bucket seem to help a lot
@BonafideToolJunkie7 жыл бұрын
Rich topsoil.
@carlosandresperezaponte36697 жыл бұрын
El Tamaño de la Maquina no es importante, lo que hace la diferencia es la esperiencia y el conocimiento del trabajo a realizar por un buen operador, esta maquina en manos de un experto aunque pequeña es completamente suficiente para hacer cualquier trabajo por muy pesado que sea y que este no supere las capacidades de fuerza de la maquina, gracias por el video, y felicitaciones al experto operador.-
@carlosandresperezaponte36697 жыл бұрын
buena esta maquina pero un pequeño consejo primero utilice la pala recolectora frontal como su fuera un buldozer y tumbar con ella la maleza y depues cortandola con la cuchilla de la pala recolectora para que la rotativa haga un buen trabajo de desmenuzado de la maleza sin forzarla ni a un paso rapido hagalo lo mas lento posible y el motor con una buena revolucion por minito para que el toma de fuerza trabaje lo mas desahogado posible y sufra las cuchillas de la rotativa lo menos posible porque puede romper una o el tornillo fusible roperse cada rato.-
@bill45colt7 жыл бұрын
i see on your upper link there is a hinge assembly on the piece going to the rear of the cutter. This link should be flexed about 3"for most of your level cutting. 1 Adjust rear wheel lower so it is on ground and rear deck of cutter is about 2" high. 2 Set front of cutter at 1" above ground. 3 Let the front weight of it be supported by the lower lift arms with the upper link in a flexed position. ---That way, your side slides wont wear on the ground by dragging all the time,,,,the cutter can better follow the contour of the ground independent of the tractor, ,the tractor wont be over balanced by the weight of the cutter on the rear,,,,the front of the blades will do the cutting and the rear of the blades will not drag on the clipped stalks and save you horsepower. Be sure to run engine at rated speed, less fuel needed,,,no lugging,,,,and plenty of torque and reserve power rise when you encounter heavier brush,,,,,thanks for the video!!
@bill45colt7 жыл бұрын
sounds like engine is running too slow also,,,is it up to rated speed of 540 rpm on pto shaft?
@joseluisflores457 жыл бұрын
go back wards it Is better with bush hog
@bill45colt7 жыл бұрын
also tears rear deck up,,,pushes it in,,,a pain in the ass to repair, If you insist on the rear approach, remove the back shield and replace with heavy chains so you have protection and flex also