I have an old Yanmar ym2000 that needs work, could t get in touch with tractor town. Replaced battery a few weeks back, put everything back in place started up & ran but the alternator started smoking, took off the positive cable the smoking stopped. Anyway possible for me to get in contact with you?
@Otisdiditagain22 күн бұрын
@@DarianReynolds-kz9nx sounds like the alt. Is shorted out. Call the number that's on the website Tractortown.com
@thomasrivers758523 күн бұрын
Where did you find the common rail pressure sensor WITHOUT going throw kubota an having to get the common rail plus senor together
@Otisdiditagain22 күн бұрын
@thomasrivers7585 lots of research on the ol' interwebs and crossing part numbers. Keep in mind the people who make that sensor put there name and part number on it.
@thomasrivers758522 күн бұрын
@@Otisdiditagain kamalnomics showed today in the stockmarket
@jim444824 күн бұрын
Do you know how much horsepower this Tractor has ?
@Otisdiditagain22 күн бұрын
@@jim4448 about 24 at the drawbar
@ihatephones254028 күн бұрын
Thats a good running tractor
@marvinjohnson2463Ай бұрын
Otis, did you see my second question: Can I access the 7/16 bolt going into the spline (access through the peep hole) by removing the main plate under the battery compartment? That 7/16 bolt is broken off and is allowing movement on the shaft. Some way I need to get it out so it can be properly installed with a new bolt. Is accessibllity possible once that large cover is removed if not open to suggestions.
@OtisdiditagainАй бұрын
@marvinjohnson2463 I'll try to find out and get back to ya
@marvinjohnson2463Ай бұрын
Otis, now that the final drive is removed send me a picture where that 7/16 bolt is located ….from the back side of the final drive. Thank you for the video, very helpful!
@OtisdiditagainАй бұрын
@marvinjohnson2463 I would but this video is a year or so old
@marvinjohnson2463Ай бұрын
Question: the bolt that you used a 7/16 wrench on through the “peep hole” that you in UNtightened that tightens into the grove that hold the
@marvinjohnson2463Ай бұрын
Sorry posted before I wanted…..continuation …Shaft in place. I have a situation where that head is twisted off. How do I get to that bolt to back it out and replace with another bolt? Thank
@Otisdiditagain27 күн бұрын
@marvinjohnson2463 I've had them broken before, and you've got to get a slide hammer to hammer out the shaft. It's not easy but can be done. Once you hammer the gear out and pull the final, you can repair the broken lock bolt.
@ihatephones2540Ай бұрын
good lord that looked bad lol but in NC its been up to the low 100's with all the humidity
@ihatephones2540Ай бұрын
good lord that looked bad lol but in NC its been up to the low 100's with all the humidity
@OtisdiditagainАй бұрын
Looks much worse in person
@josecaballero33052 ай бұрын
How much does it cost to change the ClutchJohn Deere 450 track loader including part in labor thany you
@NathanPellham-yo8pl2 ай бұрын
I'd love to own one with a winch, and blade. an ol MC or 40 model was the first dozer I ever ran and would love to have one to add to my ol equipment roster, I own a ol allis hd5b but she's been heavily modified I use for my business and could use something a little smaller and one a little bigger funny enough
@TractorJeb2 ай бұрын
You wouldn't happen to know anything about a 269 new Holland square bailer would you?
@ihatephones25402 ай бұрын
i aint ever heard of no 2240 but good to know that the bolts like to back out if i get one
@TractorJeb2 ай бұрын
So true
@TractorJeb2 ай бұрын
Favors a 1010
@TractorJeb2 ай бұрын
Clean and good rubber
@TractorJeb2 ай бұрын
Dang right I like tractors
@Otisdiditagain2 ай бұрын
So do i...so do i
@TractorJeb2 ай бұрын
That's begging for a cab and skid pan for the woods bush hogging
@patriciaadams-rl4iz2 ай бұрын
I have a 1949 9N, still love it. Do you have s brush hog with it?
@Otisdiditagain2 ай бұрын
We keep many in stock to choose from at tractortown.com
@1957rickster2 ай бұрын
Are you confused with a licensing agreement between IH and Mahindra to build the tractor for the India market in India (Similar to Massey Ferguson & Tafe)? Some internet history shows parts from England shipped to Louisville KY for tractor assembly. Any IH workers out there from the Louisville plant?
@Otisdiditagain2 ай бұрын
No sir, ih contracted Mahindra to make all casting and associated parts in 1963 I think. To be partially assembled in England and was then shipped to Louisville for final assembly. These castings were used for many year and then sold to Mahindra for their branded tractors sometime in the late 80s early 90s.
@1957rickster2 ай бұрын
Tractor fail or lug nut fail? Shabaura tractors were the best coming out of Japan in the 70-80’s time frame. Ford /New Holland should never have severed the relationship with them.
@curtisdowling37733 ай бұрын
I love my old ford 971
@evracer3 ай бұрын
Just had Diesel on my L3901 tonight. That is NOT where the connector is. The connector is the BLACK 4 pin connector to the left of those two. It matches diesel connector 3151/T55. Oddly enough the tractor I am working on is also having injector issues. I was able to do injector kills, read the coding on the injectors and verify the high pressure pump was working fine.
@frontwoodsfarmer20633 ай бұрын
That is one beautiful tractor
@thegreenerthemeaner3 ай бұрын
These were the best of the 7xxx series. 268 vs 256 engine, better hydraulics and no Load Monitor sensing. Load Monitor needed better flow to be a great feature which ironically the later 10 Series II had. Got rid of the springy balls on the ramp actuator in the drive line for Load Monitor as well.
@ihatephones25403 ай бұрын
didn't know they made a high crop 4020 neat
@Otisdiditagain3 ай бұрын
The 3010 H was also popular
@b.g56.663 ай бұрын
Never run one but those fords 7610's seem to run forever and are very simple
@Otisdiditagain3 ай бұрын
One of the best Fords made before they changed to New Holland
@guypatts4944 ай бұрын
Fix it it's a beast
@24681359David4 ай бұрын
Looks like it's in need of a new set of rings and a head job!
@czechmate69164 ай бұрын
Beautiful Deere love the sound of those popping Johnnys
@howardkettner4 ай бұрын
Nice units. Any of them for sale?
@Otisdiditagain4 ай бұрын
All of those are long gone
@howardkettner4 ай бұрын
@@Otisdiditagain Thanks for your prompt reply. . .
@Otisdiditagain4 ай бұрын
Thanks for commenting
@bombardier3qtrlbpsi5 ай бұрын
I had a br all it did was cut fire wood. Had a buzz saw mounted on the front. Bought it for 75$... Sold it for 5000$. Should of never sold it😢
@Otisdiditagain5 ай бұрын
She really a classy ol'gal
@ihatephones25405 ай бұрын
nice runnin deere
@Otisdiditagain5 ай бұрын
Not too shabby
@Tiuuuu7526 ай бұрын
Tylen love 💘 ❤ 0:14 ❤
@FarmallFanatic6 ай бұрын
Sell it yet?
@FarmallFanatic6 ай бұрын
For sale?
@Otisdiditagain6 ай бұрын
It will be soon
@FarmallFanatic6 ай бұрын
Do I like old tractors? Nahhh 😂
@stoptheirlies7 ай бұрын
So you think making a KZfaq video just means putting a camera on a stand and let it film you working.? Ok may suit some not me, I like to be included and spoken to, or at least a running commentary on what you are doing. I'm gone.
@Otisdiditagain7 ай бұрын
Ok thanks for stopping by
@bearbait22218 ай бұрын
Is there suppose to be hydraulic oil in the steering clutch compartments? Mine is full to the top on both sides and leaking out the top. The last entry in the mech logs before i got it at auction is" hyd oil leaking into clutch. I assumed they meant the main clutch. I did see an early service bulletin On the 80's 450c something about making the clutches a common sump because of a hose that leaks? I have been looking for an oldtimer mech that knows the 80's 450c inside and out. So i could pick his brain. They are all retired :(
@tomrose62928 ай бұрын
Is a 350 basically the same?
@WhiteyTheIronMonger8 ай бұрын
I hope you can find a way to obtain ownership so you can get off top dead center. If you can part it out the Historical Construction Equipment Association might be a good place to advertise. She still has purpose for someone.
@bearbait22218 ай бұрын
Wow you never see a jd 450 with stock front idler wheel guards i have been looking for years to put them on my 450. I can't get enough of the 450 repair vids. Thanks.
Get lien on it don't be afraid about.then start put tlc on it.tried contact some used scrap yard and rebuilt it.i ran d8h longtime ago in alberta pipeline job was park farmfield.the company need dozer due one broke down yup new d8r so trow few buck back on job for end pipeline job.good luck lien and video.😮
@dennisbaker559610 ай бұрын
450 c dics first and plate
@AppalachianRust10 ай бұрын
Don’t scrap part her out. This one’s old but some guys still running them and parts are hard to find