Only swimmers shave their legs.

Nice Fix! 👍 And Haters are gonna hate!!! Just move on! 😉

do you know if you have a black fluiđ you ne,ed to flush the line. the red fluid you don't ne.ed to flush other why when you put the new fluid in the mix red fluid black and red together

Good job 👍

Can IP508 check the vehicle's battery State Of Health(SOH) and State Of Charge(SOC). I need to know how to check the battery life % with XTool iP508. I have it.

Just ordered your stuff from Amazon. Would there be another name on specifications for the kingpin measurement? Also nice video.

Didn't know the engine has to be running for the test? 😂

Does this unit have carbon filters for indoor venting?

Great tip on the hole saw drilling from both sides!

Solid floor never is never the sign of a solid boat. They rot from the bottom up…. I bought a 1988 regal medallion for its engine. The original floor is actually solid. I thought it might make the lake once or twice. I started it and noticed the engine was dancing. Front motor mount gone. Rear stringers gone. Deck overs are dangerous… also why I play with tin boats only unless it’s with a saw all and a dump trailer

Going to attempt this today on my son's 2010 Mazda 3

Just channel lock it and I used a big flathead screw driver and hit the channel locks. It came off Finally. Wasn't easy I admit but wasn't as hard as I thought it was going to be. Chanel locks I had on tight as I could squeeze them

Spray some used motor oil inside that x-member to keep it from rusting.

I would love to learn how to weld. I have a 1993 Buick Century that is like your car perfect and clean except for a couple of spots. It has similar rust repairs needed. Good video.

Here is another tip. When replacing the filter clean the hole in the transmission with a shot of brake clean so there is no oil and the rubber ring has a better grip. Then use green Lube Gard assemblee goo on the contact points of the filter to the valve body. This will hold the filter in place until you can get the pan on. Put the assemnlee goo in the refrigerator for a few hours to make it extra sticky. This product is made to be used in automatic transmissions and will dissolve in transmission fluid. For some reason Ford could not put a screw in the filter to hold it in place. They probably saved 15 cents per transmission by doing this.😑

I wish I watched this before I broke the screw extractor 😢

Thank you. My car has a different issue. The driver side lock doesn’t lock with the remote. We get around by doing it manually from the back door. Is there any easy fix to it ? The dealer wants too much money to fix it.☹️

Also here is a tip if you are not into transmission fluid waterfalls. Drill a 1/4-inch hole in the bottom of the pan first, then remove the dipstick, and let the fluid drain out into a pan for an hour or two. Then remove the pan, replace the filter, clean the pan and magnet. Plug the hole you drilled with JB weld, let it set up and replace the pan. Refill with the same amount of fluid you drained out. A cleaner job without all the mess.😊

I have watched several of these videos and many comments state that they would drain out 5 1/2 quarts of fluid and have to install 7 quarts of fluid to get the proper fluid level. So does this mean that the factory under filled the transmission? Or is the transmission now being over filled? Kind of odd there could be such a difference. There is some fluid in the filter but not that much. Also, I have found that welders gloves help when checking the fluid level.

A couple of things about chickens and nesting. Yes, they do not mind (possibly even prefer) nesting together. However, if you have a strong pecking order in the flock, have at least one separate box or compartment for those at the bottom of the pecking order. For your nesting box, just the one divider in the middle, would have been fine. Yes, they like to roll other eggs under themselves, this is common. Sort of like an inbuilt habit. The bit of tin you put on the top is a bad idea. They tend to jump up on things, and would therefore cut their feet and get infected.

Good deal. Thanks

Amazing job, I have the same boat. Too bad the triple backflips were off cam.

Thank you. Who designs those things... surely ergonomics and comfort should be big on the list.

Im hoping this works for me because im in the same boat. Thank you for posting the extremely helpful video ☺️👍

This looks like the situation I have now, But my hole is directly underneath the O2 sensor, and the flex pipe is starting to go.😢

Thanks that was super helpful and I really appreciate the visual demo.

Ypu cant use pressrue treated plwood in an aluminum boat or you will destroy it. This is not a good idea, you are better off using regular pywood than this. But really they make marine geade plywood juat for this purpose,and other than replacing your wood floors with more aluminum, marine pkywood is the only good solution to rotten floors.

I think they adjust these newer headrests for the new gen of kids with forward head posture because of always being on their phones

Thank you, nice 👍

reset the springs. It takes 30 seconds and anyone can do it.

I still think removing the trans line and allowing it to pump out is worthwhile... It was able to pump out a little less than 4 quarts...

My 2020 f250 drives Me f... nuts! The headrest are definitely getting adjusted

Good idea on brake light check

Excellent video!!!As a side note, Bug was heard saying: Hey, Mister, can you please go somewhere else to do your teaching videos??? I'm living up to my pest expectation... Don't make it harder to get inside!!🐞🐞🐞🪲🐛

What the heck is all that clicking noise!!!!???! 😡😡😡

Why didnt you run power to the solenoid to see if it moves in and out?

Just came across your channel 👍 What lower end scanner do you like that can analyze the powerbalance, VCA bank 1&2, etc for troubleshooting?

Next stop Gold Slucing!

wow, pretty sure thats the same engine as my Ford 1320!

i believe pressure treat wood will eat up a boat, so just use plain ply wood an put resin on top to make it water proof.

Super

Car

what are your thoughts on just putting the 3/4 plywood all the way to the back? I have another soft spot over the gas tank. it's not terrible, i'm 300 pounds and i can walk on it but it definitely flexes and the carpet and gel coat on top are rubbed away exposing the old wood.

cheapass crap made under brand names in China

Thanks for showing the cable routing, and pointing to everything. Put Rhino 700 in the video title if you can, it should get you more views!

I took my glass apart and when I did the springs fell out . Any clue how to get them back attached to hinge . Or would you have to replace . Nothing looks broke just spings fell off so door isn't closing at all. 😒

I just love how you literally skip the hardest part to do in the whole job! I'd bet 900 of the thousand views you've got are to watch how you installed the snap ring and you skip it and show it done and explain how you did it that's not how you make videos of how to do something!!!!

Nice!

This is the best alignment video i can find, you're the man.

I had a broken wheel on the bottom of a slider wheel. The wheel is spring loaded with coiled spring. I could not find this type on the tube. However, this video helped in adjusting the top and bottom tension screws well enough to operate the slider smoothly. Thank you very much for this video.