Do you know if there is a way to convert these 420s to a standard foot shift? I know on the 2000s ranchers and foremans you could but I can't find anything on the 420s
@ballervision13643 күн бұрын
did your gear light use to blink whenever u turned it on?
@BellyUpFish3 күн бұрын
Yes. I don’t remember the sequences and what they mean, but I got shift motor issues.
@joucellvelazquez15225 күн бұрын
Bike wont even start how am I supposed to tune it like that
@BellyUpFish5 күн бұрын
If it won’t start you have other problems to sort out first. What is it doing when you try to start it?
@joucellvelazquez15225 күн бұрын
@@BellyUpFish it just cranks but won't start. I replaced a ton of parts already on it and it just cranks . It does have spark but I'm guessing it's getting too much fuel
@BellyUpFish5 күн бұрын
@@joucellvelazquez1522 So, it’s either fuel or air, if it has spark. Pull the carb and see if there is fuel in the bowl.
@joucellvelazquez15225 күн бұрын
@@BellyUpFish thanks brother I'll definitely check that. I also opened the bolt on the bottom to bleed gas through the lines and it goes through with no problem
@BellyUpFish5 күн бұрын
@@joucellvelazquez1522 Ok. Thats your drain, so there is fuel in the bowl. Is the carb new?
@JamesTaylor-lx9nv8 күн бұрын
So will a pz20 carburetor fit a atv that normally runs a pz19
@BellyUpFish5 күн бұрын
I don’t know. Wish I could help there.
@joestamper564910 күн бұрын
good video very helpful
@Gkir111 күн бұрын
How would you work out the ratio it dilutes?
@BellyUpFish5 күн бұрын
Easiest way, I think, would be to know the flow rate of the water going through the pressure washer, which could be timed by spraying into a bucket. Then time how long it takes to empty the foam cannon container. That should give you both flow rates. Take those flow rates and work out a ratio between the two. Should be able to reduce that to a dilution ratio.
@mariah17011 күн бұрын
You are a life saver! Just tried this after laying in bed trying to resist scratching my legs and thighs. I finally can lay down in peace. Thank you so much! 😩
@ThePl87pll14 күн бұрын
Can someone please help me. I have this exact carb on my coleman at125ut and it fires up immediately, idles perfect , but when I go to give it gas it just goes blurp blurp. Doesn't go fast and bogs down or something. I've tried relentlessly adjusting the screws with no luck. This is my 2nd carb like it. The first one lasted a few rides until it did this and this one lasted a full ride around the neighborhood until it started going blurp blurp. Helpppppp please lol
@BellyUpFish14 күн бұрын
If it’s idling fine but dies under throttle it’s not getting enough fuel. Have you cleaned the carb? Was this a new carb? I always clean a new carb.
@ThePl87pll14 күн бұрын
@BellyUpFish Brand new carb. What is there to clean and where on it to clean? It's so clean looking already lol
@BellyUpFish14 күн бұрын
@ThePl87pll Junk inside any of the passages from manufacturing. These aren’t built under the strictest of quality control.
@ThePl87pll14 күн бұрын
@BellyUpFish idk man. It appears to be getting plenty of fuel. Maybe I just got 2 bad carbs. I'm lost at this point
@sojourn154415 күн бұрын
Next time use butter instead of oil and it won’t stick at all. Great video!!
@BellyUpFish14 күн бұрын
Thanks, I’ll give that a shot!
@longcashdj338116 күн бұрын
I can’t find the screw that adjust is it something covering it?
@BellyUpFish14 күн бұрын
Unfortunately, some of these carbs don’t have the needles that can be adjusted. You’ll want to grab a new carb on Amazon. Make sure you get one that is adjustable.
@LumpyFPV18 күн бұрын
Noiiicceee. Should be ok on an intake plenum gasket, what do you think?
@BellyUpFish18 күн бұрын
I wouldn’t have any issues using Vaseline there.
@user-hayden99919 күн бұрын
Thanks for posting this the kick on my blaster broke and I had nothing to ride now I can use the china boat again
@NoLyinEvry1sDyin23 күн бұрын
Dawn and bleach love each other just fine
@PiperBuilder26 күн бұрын
One of the best colony’s I’ve ever had didn’t do anything for 6 months. Also, they are in dearth conditions. My new bees never did much in their first year.
@BellyUpFish25 күн бұрын
They’re definitely not doing anything in the upper box. We’ll see what happens.
@t1mmy1328 күн бұрын
Is that tube food safe? Usually those transparent tubes are at risk for leeching into the water
@BellyUpFish28 күн бұрын
Tygon E-3603 is food safe.
@Ninoo18728 күн бұрын
Smart guy
@richardlange909429 күн бұрын
LOL, I cannot get it to work. Guess I am just too old
@BellyUpFish28 күн бұрын
Where are you getting hung up?
@richardlange909427 күн бұрын
@@BellyUpFish Thank you for the reply. I gave up trying to modify the part and just built my own with fusion. No matter how I tried I just could not get the STL file to come up without the triangles. I do want to thank you for your response. At 80 it is often difficult to get what seems simple to work.
@stevekress958529 күн бұрын
I live with three mature trees over my roof. I put these guards on my gutters and after a year my gutters and the guards are free of leaves and twigs. What is nice is they are very rigid and easily allow debris to blow off. There is no front lip to catch stuff. The more open mesh easily handles heavy downpours. I am very impressed. If you have to take the little extra step to secure them, do it! They are worth it.
@Derek_GarnhamАй бұрын
my friends car came back from having a new spring fitted, it didn't drive right, when he looked there were still a few heavy duty zip ties compressing some of the coil. Maybe useful as secondary protection once the straps are tight.
@dylanmccullick9710Ай бұрын
Any update? Did you have to replace any parts?
@BellyUpFishАй бұрын
No. Turns out it was simply my battery. I have had one other “won’t shift” issue since this video and it was the shift motor getting stuck. I took the motor apart, put it back together and it’s been shifting like a champ ever since.
@houssamelmoidef5980Ай бұрын
Underated KZfaqr
@BellyUpFishАй бұрын
Thanks man.
@donevans8373Ай бұрын
I made one like this and it worked great. But after 5-6 catches I started having the trap sprung but then found it empty. They were getting under the doors and prying them open. I installed some cam and peg latches and no more escapes.
@BellyUpFishАй бұрын
You should do a video on your latch pegs!
@jarridtaylor7778Ай бұрын
I have a 1977 WASR. Was my first rifle and never let me down. Love it! Added a Romanian bayonet
@Doughnut12Ай бұрын
That's is either skunk or badger no cat it unfriendly
@georgeund7533Ай бұрын
go doctor
@canadiancraftbrewerytoursАй бұрын
I replaced the carburetor on my son’s Tao Tao 110 Boulder. Starts up better than it ever has and sounds great. When I put it into Drive it has almost no power and eventually dies out… someone help me!
@BellyUpFishАй бұрын
Did you follow the directions in this video? I’d say your air fuel ratio is off, one way or the other.
@canadiancraftbrewerytoursАй бұрын
@@BellyUpFish I did and it’s working ! Running very well. Unfortunately it’s moving on its own in D or R even with zero throttle .. what’s up with that?
@BellyUpFishАй бұрын
@canadiancraftbrewerytours Could be a couple things. I’d start by bringing the idle speed down some. Could also check the throttle linkage.
@canadiancraftbrewerytoursАй бұрын
@@BellyUpFish perhaps when changing the carb I installed the throttle cable wrong ?
@BellyUpFishАй бұрын
@@canadiancraftbrewerytours Check and make sure the throttle barrel is in the sleeve correctly.
@jprStripes78Ай бұрын
I like the PF9's dimensions, and I don't mind the long pull, but the weight of it in such a light pistol would take too some getting used to for me (I'm used to 5-6 pound trigger puls, and even on my DA/SA SIG the pull is only about 8 pounds (THink PF9's is like 10 or 9 pounds....)
@BretChilcottАй бұрын
Thank you for sharing your knowledge. Keep up the good work!
@rowpaul4545Ай бұрын
gave up on regritting the mdf wheel, made an 8" plywood wheel, glued on 240 grit emery sandpaper, lasting over 50 sharpening and still going without any signs of failing!!!!
@BellyUpFishАй бұрын
I wound up with a KME sharpener and haven’t touched these since.
@Castrotherapper13Ай бұрын
Tfr foams well too lol 😂
@BellyUpFishАй бұрын
I dunno what TFR is. 😝
@purplemanticore6830Ай бұрын
What do i do if my atv has a metal plate covering where the air fuel adjustment screw is? I have the same atv as in the video btw. I can post a video showing it if needed.
@BellyUpFishАй бұрын
Sounds like you might be referring to a Welch plug. If that’s the case, if you have an air compressor, drill the smallest hole you can into the center of the plug and then blow compressed air into the hole and the plug will come right out.
@larondalawvere2646Ай бұрын
Thank you , helps a lot
@barenekid96952 ай бұрын
Only problem being a Good straight edge Costs as much if not more than having a machine shop resurface the head.
@fedor7695Ай бұрын
Well I just got mine for like 30$ off Amazon. The resurface at the shop will be 200$+ each
@gymshoe88622 ай бұрын
I am a tall guy who wants to fly--(6' 6")--I wonder if I would fit inside this plane? Maybe with a custom front seat?
@BellyUpFishАй бұрын
6’6” may be pushing it. I bet your could find one to sit in, in your local area.
@robertm59692 ай бұрын
Looks great! Just picked one up at a flea market for $30.
@michaelshin692 ай бұрын
My problem was low battery. I had to rev a bit to shift from R to neutral. Put a nrw Noco lithoum as the original was 10urs old.
@BellyUpFish2 ай бұрын
They don’t like low batteries. I just had another issue and it was sticking brushes in the shift motor.
@m1j9s792 ай бұрын
So its not nearly as quiet as advertised , 42db
@BellyUpFish2 ай бұрын
Yeh. It’s not terrible, but at full tilt, it’s pretty loud. I wound up mounting mine in the attic of my shop.
@BellyUpFish2 ай бұрын
Yeh. It’s not terrible, but at full tilt, it’s pretty loud. I wound up mounting mine in the attic of my shop.
@BellyUpFish2 ай бұрын
Yeh. It’s not terrible, but at full tilt, it’s pretty loud. I wound up mounting mine in the attic of my shop.
@rompstar2 ай бұрын
why did you print the base in White, which will let light through easily for algae growth?
@BellyUpFish2 ай бұрын
Because I had white filament.
@xkammo2 ай бұрын
OUT OF ALL OF THESE VIDEOS THIS ONE WAS THE ONE!! Thank you brotha. My 2020 125cc Coolster Dirtbike is able to idle now 💯
@BellyUpFish2 ай бұрын
I’m glad it helped!
@stephenmcdermott12182 ай бұрын
I recently got a new carb and air filter for my polaris trailboss 250 and after putting them both on no matter what adjustments i make the thing starts then revs higher n higher i know it cant be an air leak. Any suggestions? We have a new throttle cable on the way already.
@BellyUpFish2 ай бұрын
Is the carb cylinder on the notch in the body?
@stephenmcdermott12182 ай бұрын
@@BellyUpFish yes, it seated in as far as the old one did.
@bluegrasschannel53002 ай бұрын
Thank you
@Bill-mj8hf2 ай бұрын
My wasr 10/63 has never jammed or misfired. I LOVE THE G2. BEST AK TRIGGER MADE. Also mine has one of those mags too. What is nice is out of all of the 40+ mags i have, 20 different brands/styles, it smoothly accepts and empties ALL of them no issues. I did lose the original bolt, but in my experience they all perform about the same. 10/63 is made with military surplus/used military parts which i think is amazing because of the history. It has about 75,000 rounds through it and it just gets better with age, same accuracy, the chamber, lands, and rifling all look NEW. The gun store guy couldnt believe it we used his snake camera. It's my #1 shtf/family defense piece as i trust my life to the fact that it WILL FIRE WHEN I NEED IT TO, AND IT WILL HIT THE TARGET. I upgraded the grip, a quad rail and fire side rail and red dot with flip magnifier finally, it's got an original ak74 tanker brake, and i fixed the canted sight (its really easy to hammer the pins out, straighten it, and hanmer em back in.)
@BellyUpFish2 ай бұрын
75,000 rounds? That’s wild.
@frembo12 ай бұрын
Give us an update if the bees take to the newly waxed frames. I have yet to get my first couple of hives, but hopefully can grab them this year.
@BellyUpFish2 ай бұрын
They have definitely taken to them. Just added my first honey super last week.
@Parkinstarkey2 ай бұрын
Y’all should be wearing condoms and all that stuff too but… I’m a rebel.
@BellyUpFish2 ай бұрын
YOLO..
@jimmysblacksmithing4622 ай бұрын
Hey, thanks! This may be faster than some of my other techniques. Keep up the good work Stay well and have a beautiful day👍🙏
@rld12782 ай бұрын
Needed a bit more oil in the pan for eggs too especially since it's new. Lots of ppl precook items to take camping and hiking.
@BellyUpFish2 ай бұрын
Yeh, mistakes were made. 😝
@loganyaaj2 ай бұрын
skip to 4:45
@BellyUpFish2 ай бұрын
That’s my favorite part!
@fixingproblems31832 ай бұрын
Hello sir, I have a fine Chinese ATV likes yours. My ATV only starts with the chock up and when I give it gas it dies. It idles high, not sure what is wrong. Your help will be appreciated to get this Chinese ATV on the road with the kids
@BellyUpFish2 ай бұрын
Could be a lot of things, but it’s usually just a dirty carb. You could try cleaning the carb. For the price of a new carb, I’d be tempted to just throw a new carb on there.