@@petesgarage4670 i just found one to buy at 600 euros
@Dsw0097 күн бұрын
Throttlebody on those fail a lot be aware (had 2 beverlys 500 that both failed on the same thing, single sparkplug tho)
@Ibydibi7710 күн бұрын
Where you from if you don’t mind me asking mate and you’ve done some bikes keep going 👌
@petesgarage46706 күн бұрын
@@Ibydibi77 Hi there. I‘m from germany 👍🏻
@Ibydibi7710 күн бұрын
Love the videos man 👌
@petesgarage46706 күн бұрын
@@Ibydibi77 thx 👍🏻
@robsonrossi890718 күн бұрын
Legal acabei de comprar uma em perfeito estado, estou usando óleo mineral pois não tinha visto a especificação. Será que pode dar problema? Agora vi que o manual exige o óleo sintético.
@nicusecan799818 күн бұрын
Have you ever repaired a fuel pump?
@petesgarage467018 күн бұрын
@@nicusecan7998 sure. I‘ve done some of them
@nicusecan799817 күн бұрын
@@petesgarage4670 And if is the con rod ok but it sounds intermitend when ts connected to the line fuel . what its about the issue ? I have a couples that sounds like br br for a bit and then silent . spinning the motor normal. Mayibe they need only some deep cleaning ? maybe at ultrasounds bath ?
@PiotrWesolowski-eo3ng23 күн бұрын
Mam problem z odpaleniem kosiarki AL-KO 675 is możesz pomóc
@petesgarage467019 күн бұрын
chętnie. Świeca jest ok Zapłon Działa ?
@loardfazliu997825 күн бұрын
Hello, I have an Aprilia SR 50 ditech and it has the following problem. When I try to start it and give it a little accelerator it turns on but as soon as I let go of the electric starter it immediately switches off again. The scooter has compression and the scooter has spark. Even when I try to start the scooter every time, the spark plug is completely black every time. What should I do? Can you please help me?
@petesgarage467025 күн бұрын
hi there, have you already changed the spark plug? You have to also measure the pressure of the fuel pump and the pressure of the compressor.
@loardfazliu997825 күн бұрын
@@petesgarage4670 Yes, I changed the spark plug 3 times and measured the pressure and both are fine. It's not that
@loardfazliu997825 күн бұрын
@@petesgarage4670 could it be the control unit? or what could be the problem?
@loardfazliu997825 күн бұрын
@@petesgarage4670 It also shows all the error codes on the display but that can't be the case because it was running 2 days ago
@stefantodorov8005Ай бұрын
Hallo Peter, bei mir kommt kein Kraftstoff an die einspritzkopf an. Benzinpumpe ist neu, Einspritzkopf mit blaue düse auch. Wv volt muss immer an Stecker sein? (Es zeigt bei mir 3v) Kann es sein dass Steuergerät kaputt ist? Danke und Gruß
@5spokehubcapАй бұрын
may i use this clip for my hubcap coming off series?
@petesgarage4670Ай бұрын
its a licenced video. Read info plz.
@5spokehubcapАй бұрын
@@petesgarage4670 okay
@liltete7114Ай бұрын
Hey pete, Its my first time working on the ditech version model and I would like to ask you the injector is leaking.. Do you have any videos of replacing the o-rings on the injector? I think that it is the fuel pressure regulator at fault because It floods my engine with gas and i can see that when i take the exaust off and its leaking more fuel than needed to start the engine. Thanks!
@thomashoffmann7012Ай бұрын
Hallo, können Sie mir ein paar Tipps geben, wie ich den Rahmen auf Vordermann bringen könnte (womit behandeln?) Meine Runner ist Baujahr 98. 7500 Kilometer laut Tacho. Ist der Auspuff ( Sito plus?). Wie schnell fährt ihr Roller? Welchen Antriebsriemen benutzen Sie? Gruß aus Hessen.
@skippinlivin6887Ай бұрын
Hey , my grandpa has one and I want to rebuild it but I don't know where to buy the parts for it . Could you help me out?
@petesgarage4670Ай бұрын
check ebay out
@5spokehubcap2 ай бұрын
why kick it?
@petesgarage46702 ай бұрын
So that no one else drives over it
@5spokehubcapАй бұрын
understandable, but you broke it in the process
@alistairrobinson38652 ай бұрын
I had a silver 125 in year 2000, best bike I ever had, double disc model, brilliant, just like this but the larger engine 🙏stunning restoration work you ate very talented!
@Milandem12 ай бұрын
Hoi ik heb ook een ditech voor mijn zoon staan alvast voor als hij 16 word , enkel ook die van ons doet het niet . Zou je ons kunnen en willen helpen?
@sg_tuning2 ай бұрын
hello do you have to tune the ecu to get more then 65km (sr50 ditech)
@bestslowed49562 ай бұрын
Can u tell me how to install my carburator please
@petesgarage46702 ай бұрын
which scooter do you have? Which carb do you have? What kind of help do you exactly need?
@memetaliti82902 ай бұрын
I saw one for 100 dollars is that the normal price? Also is it a good scooter for only 100 bucks?
@patricksilas65183 ай бұрын
Ich konnte letzte Woche einen alten Ditech günstig ergattern. Der Roller stand 19 Jahre in einer Halle in der Ecke. Ich habe eine neue Batterie eingebaut, neues Bezin drauf und er ist direkt angesprungen. Probefahrt konnte ich noch nicht machen aber ich hatte das Gefühl das er im Stand manchmal nicht richtig das Gas annehmen wollte… mal schauen der Roller hat auch „erst“ 6.000km gelaufen
@petesgarage46703 ай бұрын
Das hört sich doch gut an, der Roller muss mal richtig gefahren werden, dass der frische Sprit überall hinkommt und dann sollte sich das mit dem rauen Leerlauf legen. Wenn nicht, muss man weiter schauen.
@mta4663 ай бұрын
Will a vespa lx 50 2t engine fit on the subframe??!?
@petesgarage46703 ай бұрын
engines look quite similar. You must messure the mounting holes
@vadimzlobar3 ай бұрын
Hallo, zunächst einmal großen Respekt vor der geleisteten Arbeit, die Videos sind wirklich informativ. Ich habe auch eine Aprilia SR50 Ditech und ein häufiges Problem ist das Startproblem. Der Motor geht im Leerlauf aus und startet auch nicht, wenn der Motor heiß ist. Bitte geben Sie mir einen Rat oder führen Sie vielleicht eine Reparatur durch und es wäre möglich, das Gerät zur Inspektion zu Ihnen zu bringen? Vielen Dank im Voraus! MfG
@petesgarage46703 ай бұрын
servus, bei einem Ditech ist die Fehlersuche relativ kompliziert. Ich würde grundsätzlich zuerst das einfachste probieren zuerst mal eine neue Zündkerze kaufen. bei diesen Modellen gehen die Zündkerzen sehr schnell kaputt. Das hab ich bei meinem einige Male schon gehabt. Danach würde ich den Druck am Kompressor messen. Danach würde ich den Druck der Benzinpumpe messen. Wenn der Motor ausgeht, wenn er warm ist, kann es auch sein, dass es einen Riss im Zylinderblock gibt der sich bei Wärme ausdehnt somit zu Kompressionsverlust führt. Einfach mal probieren. Viele Grüße
@vadimzlobar3 ай бұрын
@@petesgarage4670 Reparieren Sie diese Mopeds und ist es möglich, sie zu Ihnen zu bringen? Ich wollte auch fragen, wo das Problem zu suchen ist, wenn der Roller die Fehlernummer 20 anzeigt?
@petesgarage46703 ай бұрын
@@vadimzlobar tut mir leid. Ich habe leider wenig Zeit, da ich sehr viel um die Ohren habe. Die Fehlernummer einfach mal googeln.
@bruhbruh49223 ай бұрын
Perer meln aprilia sr50 gp1 stand lange zeit gibt garkein lebenszeichen von sich zündkerze funkt und auf der einspritzdrüse ist druck drauf benzin erreicht die einspritzdrüse auch. Aber ein kollege meinte ein extra kompressor macht den druck. Kann es sein dass dir eindpritzdrüse kaputt ist und wenn ja wie kann ich sie testen? MfG
@petesgarage46703 ай бұрын
die Roller haben zwei Düsen einmal die grüne vordüse und die blaue Einspritzdüse. Diedüse wird vom Steuergerät angesteuert. Wenn der kaputt ist, geht sie nicht auf. Du kannst versuchen beim Starten Bremsen Reiniger in den Luft Einlass zu spritzen wenn die Maschine anspringt, weißt du, dass es an der blauen Düse liegt.
@Okdan.4 ай бұрын
Do you sell derestricted ecu's?
@petesgarage46704 ай бұрын
no but I can derestrict yours for 30 Eur.
@Okdan.4 ай бұрын
@@petesgarage4670 Where do i contact you for this?
@Okdan.4 ай бұрын
@@petesgarage4670 Where do i contact you for this?
@Okdan.4 ай бұрын
@@petesgarage4670 Where can i contact you to exchange info?
@dokesz5304 ай бұрын
15 yrs stalling.i wonder how the piston and crankshaft bearings looks alike.even the intake or sealings.hope they all fine cuz old oil become acid and slowly corrosion will damage the all metal parts.
@muratarslan33695 ай бұрын
Was hat er denn ?
@petesgarage46705 ай бұрын
läuft nicht. Steht seit 3 Jahren
@muratarslan33695 ай бұрын
@@petesgarage4670 kriegen wir doch hin. 😀
@petesgarage46705 ай бұрын
@@muratarslan3369 aber klar doch
@Lwedg5 ай бұрын
Habe auch einen SR50 Factory Einspritzer. Ein Super Roller. Habe meinen mit 2000 KM gekauft und der ist auch top beinander. Eine Frage: Ist es normal, wenn man aus dem stand losfahren will, dass er eine Gedenksekunde hat bis er hochdreht und losfährt? Bei mir fährt der erst los, wenn er auf 4 Tausend touren ist und dann zieht er durch. Würde mich mal interessieren... Fährt deiner gleich an beim Gasgeben?
@petesgarage46705 ай бұрын
servus, die Gedenksekunde hatte ich bei einigen Vergaserrollern, bei den Einspritzern bis jetzt noch nie. Hast du was an den Vario Rollen verändert? Oder die Gegendruck Feder getauscht?
@Lwedg5 ай бұрын
Der ist noch original und da wurde nichts gemacht. Ich drehe den Gasgriff, dann dreht er hoch ganz normal und dauert etwa 1,5 Sekunden und dann zieht er los und zieht auch sauber durch.
@poztal776 ай бұрын
Verfügt die Aprilia über die serienmäßige Verjüngung am Ansaugstutzen (Metallplatte mit Loch)? Ich bin der Meinung, dass Purejets/Ditechs diese benötigen, da das Einspritzsystem über keinen Luftmassenmesser verfügt.
@petesgarage46706 ай бұрын
ja die Metallplatte ist da. Da ich über ein Interface verfüge und die Software anpasse mache ich sie immer raus.
@poztal776 ай бұрын
@@petesgarage4670 interessant, mein NRG Power Purejet läuft mit der Platte sauberer und hängt direkter am Gas als ohne Plättchen. In dem offiziellen Werkstatthandbuch wird auf die Ansaugung bzw. die Platte nicht eingegangen. Viele denken zunächst, dass es eine klassische Drossel zur Leistungsreduktion ist. Ich bin aber der Auffassung, dass die Nennleistung von 4,4 kW nur mit der Platte erreicht wird und das Steuergerät im Auslieferungszustand auf die Platte hin eingestellt ist - was Einspritzmenge bzw. Luft/Benzingemisch angeht. Es würde mich interessieren ob das Weglassen der Platte in Verbindung mit dem Steuergerät im (Developer Mode?) eine bessere Performance bringt. Ich dachte dieser offene Modus hebt lediglich den Drehzahlbegrenzer auf.
@aromato22336 ай бұрын
Hallo, was ist aus dem Roller geworden?
@petesgarage46706 ай бұрын
schon verkauft
@aromato22336 ай бұрын
Kannst du mir bitte den ungefähren km stand sagen? Auf kleinanzeigen ist einer drin der es sein kann 5900km circa sieht genau so aus auch die kratzer links etc👍🏼
@aromato22336 ай бұрын
Aber der läuft nicht… weisst du da etwas drüber? Danke im Voraus
@petesgarage46706 ай бұрын
@@aromato2233 ja das ist der
@aromato22336 ай бұрын
Ok danke, kannst du mir sagen was dran war? Will nur sicher sein, dass ich hier keinen Fehler mache😅
@axelzabicki87896 ай бұрын
Beschleunigt langsam 😂😂😂
@axelzabicki87896 ай бұрын
Mix aus 2 rollern. 😂
@and_rew97686 ай бұрын
One of the best Italian's bike ❤️🏆🥇🔝
@Andrea-fo6hc6 ай бұрын
Hi Pete! very nice job! I have a SR50 ditech like yours, but the fuel pump failed. I found a used one and replaced it. It makes the typical noise but I don't know how much pressure it makes. The scooter lights up for 2/3 seconds, sometimes for 5 seconds and then it dies, as if it floods. what do you think it could be? I noticed that after the fuel pump broke, the red injection check light didn't work anymore. Do you know how to restore it? Thank you very much
@petesgarage46706 ай бұрын
hi there, maybe the pump is not working properly. This might be the reason. You must be able to read the pressure values. your pump has to produce 7 bar pressure. not working injection light is just a dead bulb. you can replace it by removing the speedo.
@Andrea-fo6hc6 ай бұрын
Thank you Pete!@@petesgarage4670
@aleksandarmikic56496 ай бұрын
Hello friend. I almost bought the same gilerra pj. It doesn't work as it should. I think it's the sprinkler. I can't wait to continue your project to see what else there is to learn. I plan to tear mine down to the last screw, if it is I will prepare well for next summer. Gilerra pj is very rare.
@petesgarage46706 ай бұрын
it is indeed rare, but this model is very hard to work on. You need to remove all the fairings to get to the important components. I recently found a original Piaggio diagnostic tool for the purejet models is very hard to find and very expensive. I’m planning to do the next video about this.
@aleksandarmikic56496 ай бұрын
Thank you my friend. I will follow you for sure. Honestly, the engine works and the man I bought it from the code drove the engine every day. The engine does not have a top speed, maybe it is because of the rollers. I will certainly remove the tank to clean it well.
@and_rew97686 ай бұрын
One of the best Italian's bike 🔝🏆🥇❤️
@petesgarage46706 ай бұрын
absolutely ❤️❤️
@AudioElectronicsChicago7 ай бұрын
Such a good receiver
@and_rew97687 ай бұрын
One of the best Italian's bike 🔝🥇🏆❤️
@chipdoxtator90517 ай бұрын
I have had 3 of these and still currently using it love it
@Okdan.7 ай бұрын
Hey! , i have a question about the purejets, mine leaks coolant out of the air compressor hose! Do you know what might be the problem?
@petesgarage46707 ай бұрын
sure, I do 😊👍🏻you need a new cylinder head gasket😁
@Okdan.7 ай бұрын
@@petesgarage4670 but there is like a white sludge coming out of my air compressor, isn't that a mix of oil and coolant? Not sure...
@petesgarage46707 ай бұрын
@@Okdan. aaaah you need a water trap ( see my other videos ) the sludge is unburnt oil/fuel/moisture mix
@robwinter31837 ай бұрын
How did you clean it? just wondering. Did you reassemble it? Did it build pressure?
@petesgarage46707 ай бұрын
well it was a lot of work. I used dremel and sandpaper. In the end it worked fine
@jonathansoares36207 ай бұрын
amigo qual óleo vc usa
@petesgarage46707 ай бұрын
Olá meu amigo, eu uso óleo dois tempos totalmente sintético
@jonathansoares36207 ай бұрын
@@petesgarage4670 se eu colocar outro óleo nela ela pega
@jonathansoares36207 ай бұрын
@@petesgarage4670 posso misturar o óleo com a gasolina
@petesgarage46707 ай бұрын
@@jonathansoares3620 você pode misturar diferentes óleos de dois atos. você não precisa misturar óleo com gasolina, pois possui uma bomba de óleo. Isso é chamado de lubrificação separada. Se esta bomba estiver quebrada, você precisará misturar o óleo com gasolina para lubrificar o motor.
@jonathansoares36207 ай бұрын
@@petesgarage4670 SE EU USAR ÓLEO NORMAL SEM SER SINTÉTICO A MOTO PEGA OU NÃO
@parvusprinceps6287 ай бұрын
Hey bin am überlegen mir auch so ne Chinakiste zuzulegen. Wie fährt er sich, ist er noch in Takt? Lg
@petesgarage46707 ай бұрын
servus, die Kisten sind am Werk richtig lahm und machen überhaupt keinen Spaß zu fahren. Dieser Roller ist ein v4 Takt Roller und ist gegenüber den Zweitakter noch lahmer. Wenn du selber schrauben kannst und keine Angst hast etwas selbst zu machen, dann kannst du so eine Kiste kaufen. das Problem ist, dass die Dinger überhaupt nicht haltbar sind und du stellenweise einige Sachen direkt nach dem Kauf wechseln muss. Schläuche, Schrauben und so weiter. Einiges fängt sehr früh an zu rosten. Kauf dir lieber einen guten gebrauchten Marken Roller da bist du besser dran.
@parvusprinceps6287 ай бұрын
Habe damals mit Gebrauchtwagen immer Probleme gehabt, als Studi wollte ich mir nun einen Roller zulegen. Aus der Chinakiste wird wohl doch nichts, dann vielleicht doch lieber einen neuen Peugot Kidbee?
@petesgarage46707 ай бұрын
@@parvusprinceps628 beim Kissbee machst du nichts verkehrt. Ein einfach aufgebauter und relativ günstiger Roller, der in den ersten Jahren sowieso ohne irgendwelche mucken laufen wird. Eine gute Wahl.
@parvusprinceps6287 ай бұрын
Ach ja, und zu diesen Nova Rollern gibt es keine anständigen Reviews nur vereinzelt Werbevideos. Würde an deiner Stelle im Frühjahr so eine Review hochladen. Viele sind am überlegen sich eine solche Kiste zuzulegen, da der Großteil der Menschen immer weniger verdient üben diese Billigdinger großen Reiz aus. Danke für deine Antwort und viel Erfolg dir weiterhin!
@parvusprinceps6287 ай бұрын
@@petesgarage4670Danke 🙏
@robwinter31837 ай бұрын
yes...ethanol...will f up your rubber hoses.
@GS-gn3ib7 ай бұрын
Hallo ich habe mall eine frage wo dut man Ol noch füllen?
@petesgarage46707 ай бұрын
direkt am Motor gibt es den Öl Einfüllstutzen
@Junkie6728 ай бұрын
Rede doch einfach Deutsch....
@tarcizioborges55568 ай бұрын
I have one this.
@bulutermis82628 ай бұрын
Hey Pete, thanks for the great video and insights. I think I got the same issue with my 94’, could you share a link for the spare intakes?
@petesgarage46707 ай бұрын
sorry for the delay. here you go: www.ebay.de/itm/132475981697?hash=item1ed82f0f81:g:FDIAAOSwmAZk0Nps&amdata=enc%3AAQAIAAAA8AbMd80dK%2B8s%2B5r1IXNgGMui3sIlvj9VborrmnjntVs6cXE7BIGsAozlLSvxNTE6Iklb5GSRtR6QWwAlVEBqHnMUuiy6OoOJJSu1GT70DfuFVN6VBY%2BgNyjJGleuwS6FCPNB0m00GhyPtSLCxqrYzU0W8XeISCKe%2F1JIKNvXdoCxazGwH2UhmtDuGQt4PFyUbwt9FXpz3px80Ur3JucvcF3tEaCY4zG1ZTgErhXlL%2BXPfBkg3pTxz%2BwwJEqQXoa0Rc8oO19kuEXJFvqHNWbp6K5kQFXDGx5%2FgvsfNOomOoti4aYKQCDFvq61fzD8Etf9aQ%3D%3D%7Ctkp%3ABFBMhJTQnIJj
@AdventuresProjects9 ай бұрын
Can you help me? I have suzuki like this and it had seized engine, now i am rebuilding it and i am wondering what kind of gasket there supposed to be between engine blocks?
@petesgarage46709 ай бұрын
sure there are no gasket. Just use DIRKO seal.
@AdventuresProjects9 ай бұрын
@@petesgarage4670Thanks👍
@Ali-Mente10 ай бұрын
Gilera ♥︎
@adriangashi722310 ай бұрын
-----HILFE----- Hey Servus ich habe ein Problem mit meinem meiner hört sich 1 zu 1 wie deiner an mit nur einem Unterschied deiner springt an meiner nicht …. Woran könnte das liegen ?
@petesgarage467010 ай бұрын
servus, das kann ganz viele Ursachen haben. Von einer defekten Benzinpumpe über ein defektes Steuergerät bis zu einer defekten Einspritzdüse. Es kann aber auch nur die Zündkerze sein….