Yes.

You're welcome

You’re welcome 😊

I am happy to hear that from you. most people don't get it at all. So, congratulations!!

is there any point where I could explain any better? please let me know.

Great tip!

It's 2021 version. But this shouldn't be a problem. Make sure the triangle is close enough from the point of the helix and spiral

@@solidworxedu1035 Thanks

Glad I could help!

You're welcome!

You’re welcome 😊

Can you be more specific please ?

kzfaq.info/get/bejne/Z9Zoldd837XNmWQ.htmlsi=oIIrKGaXpRdkyt-g

use a revolved cut or use a wrap feature off of a plane that is tangent to the edge of the cylinder

Glad it was helpful!

Manuals you can buy to develop expert knowledge for Ducts Systems: 1. Book: Sheet Metal & Air Conditioning; 4th edition (15 January 2006) 2. Book: Manual D - Residential Duct Systems 3rd Edition 3. Book: Air Conditioning Contractors of America (January 1, 2013) 4. Book: Modern Refrigeration and Air Conditioning Twenty first Edition, Revised,

@@solidworxedu1035 thanks 😊,,these are related to HVAC , but my requirements are process round ducts which mostly inclined, someone has recommended smacna

@@RISHIRAJ-xc7tu SMACNA sounds reliable. They have 23 years of experience and their projects look quite complex. So it must be a great leadership company in the HVAC systems.

If I understand correctly your question the answer should be: You should create the chamfer at the bottom of the bolt. Then you have to select the bottom surface of the bolt and select sketch. Then you have to select the edge of the cylinder and select convert entities. There is no need to create any plane here. Then when you are at the helix and spiral option at the left hand side you have o set the starting angle at 0. By setting the value 0 your spiral line will be exactly on the right plane. I hope i answer your question. If not please let me know.

@@solidworxedu1035 Thanks for your reply! Ok, the part I was missing was that the default angle for the Spiral on first attempt was 225 degrees, not 0. Setting the "Start angle:" to zero gave the expect behavior as in your video. Additionally: as a newbie, I was unfamiliar with the "Convert Entities" command - In Fusion 360, I think it's called "Project geometry" or some such thing.

PS: I did try the thread tool but in my case, I need 45deg threads which are non-standard [so they can be effectively 3d Printed]

You can use the link below. It's the faster way to create threads in SolidWorks. kzfaq.info/get/bejne/hbyDeZaa2LmrhY0.html

@@solidworxedu1035 Thanks again. -Dave

Please share to support. Thank you 🙏🏻

Please to support. Thank you 🙏🏻

Dear Alvin, your comment is so valuable for us here at Solidworx Edu and Thank you. All of our students used to face same thing. The trick here is to fully select the sketch of the thread and drag it close to the point where you want to do pierce. NOTE: Don't drag it too close to overlap the pierce point but close to it. All in all, the best way to do it is the way that makes you feel more trusted to use.

Mr. Tuan, We are happy to see your comment on our Channel. When you start a project you have information about the Bolt you want to manufacture. Such as diameter, length and pitch and for what purpose. We know that there are categories of tolerances between bolt and nut. Most common are the ''Fine'' Category and ''Coarse'' Category). For example a standard ''Fine'' Thread Bolts (Metric) bolt of M125 has a pitch of 4mm. This is standard value. So, In most cases you use the pitch value equal to the chamfer. In the case of ''Coarse'' Thread Bolts (Metric) bolt of M125 has a pitch of 6mm. So, here your chamfer will be 6mm.

Thank you for your comment. It means so much for our Channel here on KZfaq. Yes, I can do anything you would like but please be more specific. Please, send a picture or an attachment to get an understanding of what exactly you need. Our email is [email protected] Thank you again.

Please share for support!

Brother we really want to help you, but we don't understand what you mean. We can connect on zoom or on skype and share a screen so we understand of what exactly you need. Please send pictures or a short video on our email. [email protected]

Please share for support!

@@solidworxedu1035 People like you are too good for this world, I honeslty wish I was joking

@@solidworxedu1035 I will share youre videos with every engineering student I know, bless you good sir

I appreciated. Thank you. God bless you too brother!

Happy to see your comment. It means so much for our Channel.

Please share for support!

Dear Octavio, Thank you for you comment. Brings so much value to our channel. As you notice during the tutorial i have mention that you are allowed to enter from 30-60 degree. As soon as you are within these values you are doing great!

Hello and Happy to see your comment on our Channel. I understand what you need. You want to know how to do a parametric design where you can set a specific length, width and height and based on them you can impact all the other dimensions within your design. I have made a series of tutorial of how to create a vice body like this. Maybe you can get an understanding by using the following link: kzfaq.info/get/bejne/p9OIZ91iyLeqhnU.html

Dear Derrick, Thank you for your comment. Brings so much value to our channel. Please, you have to click on the following link to answer your question where explains the tolerances between bolt and nut: kzfaq.info/get/bejne/jbxzaNmj383XfGQ.html