Hi. I went with option 1. Worked a treat, car started first try. You are a legend! Many thanks, probably saved me thousands of dollars. RESPECT to ya.
@lindsaybrown58972 жыл бұрын
well today this helped me get my b4 2002 liberty home. Thankyou … our boxes have 7pins across not 8 but was simple to just solder across the small gap on the 3 relays. The pin number still needs to be put in to stop it squealing at you ,no biggy ,but works a treat cheers!!
@Subaruej203 жыл бұрын
Hi i am putting a subaru uj20 into a seadoo and I have realised it won't work due to the key coder and imobilizer...I don't have ignition barrel so could I bypass it and get power?
@michaelwestmoore71294 жыл бұрын
Amazing, thank you. Mine was giving me so many problems at the worst times.
@scoobydoo55805 жыл бұрын
Just found this video after i bought my 3rd Scooby and having trouble with the imobiliser and it worked a treat with method 2 thanks for the clear instructions.
@mayhem1nc.6815 жыл бұрын
This worked a charm in a my05, soldering was identical to what you have shown. Saved me couple hundred bucks so much appreciated thanks. Subscribed
@nicksteve61525 жыл бұрын
Finally after my Subaru 06 shutting down on main roads and having to push the car to the side and several times where I had to leave the car overnight where it wouldn’t start. I finally found this guide as my car wouldn’t start for 3 days. Did the solder PCB and it started first go. Keypad still lights up which is good at night to keep thief’s away. Thanks for the vid your a legend. 👍
@joemariu23445 жыл бұрын
This fixed my 2002 B4 today. Thanks heaps.
@Levinathanielmusic5 жыл бұрын
Life saver
@vwfixit60696 жыл бұрын
Thanks worked for me spliced the wires I did mine like this On the plug where it connects to the control unit Connect clip side off plug the following way Pins 1 to pin3 Pin 2 to pin 5 Pin 6 to pin 8
@maxy27655 жыл бұрын
What model year wrx do you have?
@omq_hexny17216 жыл бұрын
awesome..money saver right here.
@catshaveearsonhead7 жыл бұрын
I have a 2002 wrx and just wanted to leave feedback this worked for me, thank you
@matthewclarke24526 жыл бұрын
was yours in the same location in the bug eye? My current one doesn't have one.. but I would like to disable if I get another WRX with it installed. (never liked these systems)
@uzairmooradun27757 жыл бұрын
Hello everyone, I have a 1995 Subaru Impreza GC8, swapping the old engine into a 2004 WRX USDM which have immobilizer. I have the steering column and the original car key. The problem is I dont have the Immobilizer ecu which is found on the steering column. I wanted to know how will I be able to turn on the engine, or how can I bypass the immobilizer system. Please help! Thanks
@tuqq52387 жыл бұрын
does this work on 2010s???
@HitmanStands7 жыл бұрын
This worked fine for me. After buying a new fuel pump (which turns out I didn't need to do anyway) and installing it my cs9 still died at any given time, I followed this tut and since then no more cut outs. Thanks heaps. This was very helpful.
@PlayerSpace_7 жыл бұрын
After having my car immobilise itself pretty much every drive i tried this out and It worked a charm!
@-SlipperyWhenWet-7 жыл бұрын
This didnt work for me. I ended up ripping that brandt system out with the alarm. Was easir than u think and so much better. I just took the wires from the immobiliser and ran it all the way back till i found out where the wires were spliced. I think from memory they only spliced three main wires into the cars electricals. The rest was the immobiliser. So where it was splice i cut and joined the orignals back together. Easy as that
@rafaelandresmartinez5 жыл бұрын
I want to try thhis option please am stuck with my car
@alangarnham29458 жыл бұрын
Pull the stupid Brant system out of the subies. I did with my beloved bugeye. For those who want a heads up here is a summary of instructions. 1 Under the bonnet remove the alarm, turn it off at the keypad or have a bucket of water and set of ear muffs handy, remove all the Brant alarm wiring too. Drivers side, remove the panel under the steering column. There are jumper wires, wires cut and joined to immobilizer wires and alarm wires joined to car wires. Jumper wires removed, cut wires rejoined and soldered, immobilizer wires separated from car wiring. 2 modules to be removed. also a jumper wire set to the central locking module under the right side dash. Remove it. Passenger floor area; lift carpet, remove ECU shield. 2 cut and joined wires, 2 joins only at the ECU. Rejoin and solder the original wires, cut the immobilizer wires from the original car wiring. Remove the module (as seen in this tube) from behind the stereo area. Remove the keypad. Remember this is a summary, there is a fair bit of wire cutting and soldering new pieces , tape insulation in tight places but the pain is well worth it.
@gtcoupe958 жыл бұрын
Awesome my pump would prime but starter would not crank. Fixed perfectly thanks. Soldered pcb
@fred167738 жыл бұрын
Thanks for post!!!
@Karnivool098 жыл бұрын
Hi all, i'm having issues with fuel pump activating/keypad screwing up and not accepting my code. I went to do this on my 2005 WRX after seeing people have used this method on their 05 WRX and i removed all the panels and the brant/brandt PCB isn't even there!! and there's no wiring for it there at all either as if it were ever there. Help!
@21059kenm8 жыл бұрын
No.1 screw in second panel is one of the screws out of the first panel. So not missing.
@itsmejustinsmith8 жыл бұрын
I did this and my car starts fine, but my central locking is now not working... just a heads up. probably would have investigated other methods had I known
@itsmejustinsmith8 жыл бұрын
not to sound ungrateful. thanks saved me wad of cash!
@itsmejustinsmith8 жыл бұрын
correction: reinstall the black box after with the wiring in the video and central locking etc works fine 👌
@Simon7Williams8 жыл бұрын
Thanks, works a treat! Brandt be gone, as it had me stranded again.
@i3enji2299 жыл бұрын
Hi there, do you know if the module is located in the same place for 2005 WRX's in Australia? Also I am confused with your instructions about method 1 and 2. With method 2 and removing the control module all together and still being able to turn the car on, do I need to take any further action beside this or is it simply just removing the module?
@omarjoud21329 жыл бұрын
Life saver, thank you!
@bretth32249 жыл бұрын
Thanks to this video mine will never give me troubles again, thanks for posting
@mhmy019 жыл бұрын
Hi thank you I done this to my 05 Wrx today. Took 5 mins. Fixed the stupid brant alarm cutting fuel pump while driving ! Your a legend :)
@wildfireengravingptyltd81379 жыл бұрын
Just did this on my 05 WRX, bypass was identical, thankyou so much for the great info.
@fredtran73549 жыл бұрын
Hi, thank you very much for this video guide. My MY06 seems to have a problem with the Brant as well. After entering the key code, and turning the Key to the ignition, nothing happens, no cranking, no sound. I can hear the fuel pump priming but that's about it. The battery is ok and the "reds" and lights are on with no flicker. I did the bypass on the circuit as stated [IMG]i62.tinypic.com/of21rc.jpg[/IMG] but it still doesn't start. I am doing it wrong? or am I missing a step somewhere?
@killorglinrebel10 жыл бұрын
Thank you, this just saved me a considerable amount of money - my car would'nt start due to brant not working - i would have had to get it towed to the dealer and fixed there