2 жыл бұрын
Пікірлер
@larrytinnin3357 15 күн бұрын
Do you have a video on the different types of fastners?
@jorgevillarreal4210 4 ай бұрын
WHAT ABOUT THE ATTACHMENT????
@broski1166 4 ай бұрын
So I am building a 12x24 shed that will be used as a small powerlifting gym. I want to to use composite decking and concrete for the floors, that will be sitting on 4x4 pressure treated skids on a gravel pad. The reason for this is so that the entire shed can be moved vs just pouring a concrete slab and building the shed on top of that. My question is, what size of composite decking would I need to use to withstand a live load from someone deadlifting say 600lbs, and the weight being dropped from approximately 4ft. My original plan was to have 4 skids spanning the 12ft wide distance, so three separate runs of 4ft unsupported span. I could add another skid and make the unsupported spans only 3 ft. just wondering if this might work?
@WesternStatesMetalRoofing 4 ай бұрын
If you are not pouring concrete then you can use a roof deck. The deeper the deck = the stronger the deck. 1.5" or 3" deep will be your options. Here's a link and you can find load charts in the roof deck catalog that's located on the products pages for the different types of decks. God luck with your project. www.metaldeck.com/metal-roof-decking
@ZT-melinda 4 ай бұрын
thanks very much
@hobohank2040 10 ай бұрын
looks like a brake chamber from a truck
@deankay4434 Жыл бұрын
Very informative as I have no need for waste, I would call to find the sheet length under 9 feet. The amount will be due to my calculations because of shape and the fact it is being welded into one piece.
@Ashroyer86 Жыл бұрын
I have smooth composite. Looks like the composite here with no embossments. What are pros and cons? Its galvanized.
@vergoregiste5300 Жыл бұрын
Thanks for the info
@waltroderick101 Жыл бұрын
WHy is it called composite vs the roof deck which isn't?
@WesternStatesMetalRoofing Жыл бұрын
Form deck is not composite decking. Composite decking has embossments in it. Composite metal decking and the concrete bond together to create a composite metal floor deck. The main advantage of a composite metal floor deck is that it will increase the strength of the floor without adding extra weight. With form deck that doesn't have embossments it is simply there to support the weight of the concrete. Roof deck is smooth and does not have embossments.
@LiloUkulele Жыл бұрын
Good Morning, My B deck layout, in the 36" direction, is 5" short. My inside parapet to parapet dimensions is 15' - 4". That is 5 - 36" panels with 5" left over. What is the correct detail to fill the 5"?
@Beatman938 Жыл бұрын
I have a client whos entire house is metal frame all the way up to the roof trusses with a metal decking substrate such as this and she has standing seam metal roof panels installed on top and has replace the standing seam panels. What method do you recommend to go about doing that?
@Beatman938 Жыл бұрын
I have a client whos entire house is metal frame all the way up to the roof trusses with a metal decking substrate such as this and she has standing seam metal roof panels installed on top and has replace the standing seam panels. What method do you recommend to go about doing that?
@dennishubbard4385 2 жыл бұрын
𝐩𝓻Ỗ𝓂Ø𝓈Ｍ
@LiloUkulele 2 жыл бұрын
How much end overlap from one sheet to the next? or are the sheets butted together?
@WesternStatesMetalRoofing 2 жыл бұрын
The metal decking overlap is a 2" minimum. Most jobs are overlapped, 2"-4". Must be overlapped over a support beam/joist. The greater the overlap the worse the deck will nest at the sidelap.
@LiloUkulele Жыл бұрын
@@WesternStatesMetalRoofing Thank you for your reply. I have a total run of 32'-8". I am assuming 2 -12ft panels and 1-10ft panel cut down to 9ft, allowing 2" overlap at each end of the 9ft panel. can panels be swaged or will the 2" overlap work without too much interference? We are using metal C joists (800 S 200-68) for roof joists, I am having a hard time finding a span chart for ROOF C joists...all the span charts are for floor loading. The HSB-36 (22ga) will easily span 36, 42, 48, etc. but the joist span charts only go up to 24"o/c spacing. The roof load is just rigid insulation and roof board....trying to come up with the most efficient design....Thanks again for your help.
@WesternStatesMetalRoofing Жыл бұрын
@@LiloUkulele Lilo, Flexospan publishes a load chart for C Purlins flexospan.thomasnet-navigator.com/Asset/Z-Purlin-and-Girt-Structural-Steel---Load-Table.pdf As far as the B deck sheet lengths go you will get 36" coverage and they can be cut to any size.
@LiloUkulele Жыл бұрын
@@WesternStatesMetalRoofing Thanks for the quick reply!!
@LiloUkulele 2 жыл бұрын
From an Architect's perspective; very educational.
@iviedorolice7869 2 жыл бұрын
b2528 vur.fyi
@deyrobyn7137 2 жыл бұрын
nd865 vyn.fyi
@amilcarj.garcia2086 3 жыл бұрын
Could this cuts be made by another kind of saw? Is this the one you recommend?
@WesternStatesMetalRoofing 3 жыл бұрын
Another brand of saw with the same kind of design and blade would work. Here's an article that may be useful blog.metaldeck.com/cutting-metal-decking-saw-blade Good luck with the project
@CoryCDS 3 жыл бұрын
Sawzall and grinder works but this is definitely the way to go ive even cut through with snips but thats not fun at all
@eddiehancock4728 3 жыл бұрын
Hi
@eddiehancock4728 3 жыл бұрын
Decking is exciting
@moisesbeas7752 3 жыл бұрын
Love the channel you need to post more frequently keep up the good work
@WesternStatesMetalRoofing 3 жыл бұрын
We appreciate the support and we will be posting more regularly. Appreciate the support.
@user-tr5vl3yb7m 3 жыл бұрын
0:56 1000 subs for 15usd whatsapp +79671570581