How many miles does this new battery last for? I just did the same swap with a Agomola 36v 20ah battery.
@VenturesTruckParts12 күн бұрын
The life of the battery will depend on how good the battery is. Its to hard to say how long it will last. I did notice a big increase of how long each charge lasts and a little more power. Hope you are happy with your swap!
@michaelaudy641514 күн бұрын
Not one needle lost.. impressive
@DelvalleOficial-ohio722 күн бұрын
Great tank god bless you
@user-jg2pw5tl7z22 күн бұрын
Thank you !
@poormansyoutube68628 күн бұрын
Hi everyone what is the part number to that needle bearing by chance ?
@VenturesTruckParts26 күн бұрын
Here is a link. venturestruckparts.com/product/ford-f250-f350-excursion-front-outer-shaft-bearing-hub-bearing-1998-2004/
@poormansyoutube68626 күн бұрын
Hi everyone I found the bearing part number at AutoZone it's b 2110 for the needle bearing and the thrust washer that goes behind the wheel hub part number is 47766 thanks all
@azeeninety55Ай бұрын
What about the Oring that comes with em from spicer?
@VenturesTruckPartsАй бұрын
kzfaq.info/get/bejne/ibaYftaiq9aUn6c.html 4:50 of this video
@SEMPER-FI-777Ай бұрын
Ty 4 this video....👍😎🇺🇸😇
@ScrapDaddy-mb6vgАй бұрын
Thanks for taking the time to explain clearly all the details
@rafaeldelgadillo1613Ай бұрын
Great start to finish with details .
@ritzbitzxАй бұрын
Does this spin when you unlock the wheel and leave it in 2 wd? I have this issue but im wondering if i can temporarily tie wrap this thing down front clacking and just drive 2wd for the time being.
@user-ec7ri7zn5t2 ай бұрын
Awesome video. Showed me exactly what I needed to know. Thank you brother
@wildhorseranch1282 ай бұрын
@Ventures Truck Parts, I accidentally put a Dana 50 axle into a Dana 60 front diff. We'll, one side, anyway... The driver's side wouldn't go in far enough, which raised the alarm bells. That's when I notices the difference in axle size/splines. So, the passenger side has the 50 installed, and I beat the piss out of the driver's before stopping and putting the 60 back in. My question is, what was I beating the axle shaft against inside the diff when trying to get the shaft to seal? Could I have done damage internally?? And how about the wrong shaft fitting into the passenger side??? Will it JUST not engage properly, or is damage already likely done???? Switching to the Dana 60 axle asap, btw...
@jonparker41082 ай бұрын
Great video
@condoncole212 ай бұрын
This is the only thing that worked after trying so much bullshit
@cowboysfbfan44172 ай бұрын
Is there different hubs for autolockers ?
@outcastfpv76552 ай бұрын
Thanks for not making this video 10min long. I just needed to know the flathead screwdriver pop off bit. To the point no mucking around. I appreciate it 👍
@brianblithe22712 ай бұрын
ford dealer parts told me cant get the black hub o ring or the selector switch (plastic on/off outer switch part, it does come out but theres a trick, move it to between c and k in "lock") v groove oring unless you buy a new locking hub assmbly. I could prob source one but today there is no American made legendary quality company oring kit anymore. If anybody knows of one still left, please let me know.There is a bearing inside as well, anybody know if there are any numbers on the bearing ?
@jamesmorgan67822 ай бұрын
Thanks I will look and see .
@brianblithe22713 ай бұрын
I am looking at your website and found these front outer hub/shaft bearings so great stuff, my next quest. is, these are the outer, is there a front inner hub/shaft bearing ?
@VenturesTruckParts2 ай бұрын
No bearing that holds the shaft in the tube.
@brianblithe22712 ай бұрын
@@VenturesTruckParts Sorry if im dumb but to clarify this, you are saying this front outer hub/shaft needle bearing on the backside is the only bearing on the inside of the hub that is around the stub shaft ????
@VenturesTruckParts2 ай бұрын
@@brianblithe2271 The small needle bearing is the only one you can change. Its function is to hold the weight of the axle shaft. The actual hub assembly itself holds the weight of the truck. It is not serviceable. If your wheel bearing is bad you will have to replace the whole unit hub.
@brianblithe22712 ай бұрын
@@VenturesTruckParts Thanks for the explanation, you guys are one of the most professional and bad ass in this business !!!
@brianblithe22713 ай бұрын
@ 9:48, you saying that we can take this hub bearing out ? I was under the impression that you could only buy the whole hub ? if so you got any dana/spicer officials or OEM ?
@VenturesTruckParts2 ай бұрын
Yes i have them available. here is a link. venturestruckparts.com/product/ford-f250-f350-excursion-front-outer-shaft-bearing-hub-bearing-1998-2004/
@mikereed88323 ай бұрын
Well done… excellent video.
@hjfcoco3 ай бұрын
Part number please.
@VenturesTruckParts2 ай бұрын
Here is a link. venturestruckparts.com/product-category/polaris-u-joint-kits/
@hjfcoco2 ай бұрын
Awesome ty 🙌
@jamesmorgan67823 ай бұрын
Does this work for a 450 super duty?
@VenturesTruckParts3 ай бұрын
What year of 450? it will be the same if its a 1999-2004
@jamesmorgan67823 ай бұрын
@@VenturesTruckParts 2004 model. F 450 superduty
@VenturesTruckParts3 ай бұрын
Yes, it will be the same process.
@jamesmorgan67823 ай бұрын
@@VenturesTruckParts Do you know part number for this truck. It’s a 4x4 F450 super duty with 6.0 engine?
@VenturesTruckParts2 ай бұрын
@@jamesmorgan6782 Here is a link. venturestruckparts.com/product/ford-f250-f350-excursion-1999-2004-front-axle-warn-4x4-locking-hub-set/
@5.43v3 ай бұрын
More like 99.5-04
@robertgudger5893 ай бұрын
It will only go together one way
@markomatic60953 ай бұрын
So 06 f350 doesn't need thrust washers?
@VenturesTruckParts3 ай бұрын
No, 2006 will not have thrust washers.
@alvankhan50944 ай бұрын
My 2000 excursion 4x2 7.3 diesel making a thump noise when braking
@tommy5ification4 ай бұрын
What if you just put some grease on your fingers and put them in the tube to hold the axle up and then just slide your fingers out when you’re close enough….
@matthewowens4554 ай бұрын
This is a w4 1770
@magdump73804 ай бұрын
Now weld them up.😉
@kennyoquinn39914 ай бұрын
I don't usually comment on these videos, but I must say This was super good. Thank you for posting this. I've got a bad upper ball joint and was scratching my head how the axel comes out. Again thank You!! Edit... My darn vaccum and axel did not come out as easy as yours!! cut my behind, but at least I felt confident how it is supposed to come out.
@Muravied4 ай бұрын
Thx dear
@tone5694 ай бұрын
How do you remove the main baring in the hub Assembly ?
@brianblithe22712 ай бұрын
I heard to oil it repatedly then use flatheads but never done it. I also want to know if there are any numbers on bearing and if we can still get a replacement somewhere.
@martinfromseacity20105 ай бұрын
Very clear, Thanks. I love my 99 F250 super duty and have heard a lot of good things about the Dana axles
@tommytran29755 ай бұрын
I have a 2020 450 with a bent driver side axle tube. Will a 2012 450 axle assembly fit even if I have to swap gears over?
@user-gl6gv2ux5y5 ай бұрын
Great video
@P.B.Theriver5 ай бұрын
Excellent detail in your videos.
@choncunninghan22755 ай бұрын
My 04 F350 hub looks nothing like that. 😅
@siscoe19865 ай бұрын
What is the part # for this wheel hub?
@ben26875 ай бұрын
Excellent video. Videos like this are extremely helpful when working on something new to you. 👍👍
@williamheinsinger73905 ай бұрын
💰💰💰💰💰
@jakefortman6 ай бұрын
Very good video dude straight to the point i like it awesome job keep em up im subscribing for sure
@kenj.88976 ай бұрын
Nice vid
@silvergrizzly3166 ай бұрын
3 months ago I put a entire brand new front end under my 2000 F-350 7.3l and I did it with watching and learning from you guys. Thank you so much for sharing your knowledge 🙏 👍👍 Jay.
@briklinarocho48446 ай бұрын
What kind of grease?
@Jysko_Prod6 ай бұрын
Bonjour j ai un moteur hatz 2 cylindres je trouve pas mon préchauffage dessus ?
@RetroCaptain5 ай бұрын
Electric connection on the intake manifold. Goes to a Murphy switch.
@VIP8547 ай бұрын
wait so that seal doesnt go all the way into that axel end to block the entry? you just left it dangling there..
@Ptbocam7 ай бұрын
Hey I learned something. Never gave thought to driving up from the bottom. Nice video.
@holeshot17217 ай бұрын
I shit is shattered inside im scared to see whats inside! Im hoping its the locker hub so i dont have to pull the axles!
@azeeninety552 ай бұрын
You're gonna have to pull axle anyway. My vacuum seal went along with stock lockers all busted up. I thought same thing thinking just lockers
@julesprice58057 ай бұрын
The food DOESN'T last 25 years. You are NOT freeze drying the food, you are vacuum sealing it. Freeze dried food last 25 years, NOT vacuum sealed food! The amount of time that vacuum sealed food last depends on how you store it. Cool, dark, storage is best. You also need to check your jars to make sure no seals have come lose.
@jeffweinstein173Ай бұрын
He's assuming that you realize that he's sealing food that has been freeze dried.