Nice to see you simplified this. The intake for the 300hp skis was far mote involved to install than it should be.
@rogernascimento50062 күн бұрын
Is that in stock ready to ship
@mikehaigler18243 күн бұрын
Hey I have 2 Kawasaki stx 15f Jetskis and I am a new ski owner so I’m new to the ski world, but I have an issue I would like to see if you can help me figure out, Okay on a recent river trip I had the impeller shaft bearing fail, I replaced the bearings,shaft, cone, impeller and used the original jet pump housing. I used kawiperformance upgrade shaft kit and got a solas impeller with stock pitch. Everything went together nicely, and I have rode the ski several times and have noticed a slight vibration? Is the best I can describe the sound, but it only happens when I am at a consistent speed around 34 mph but if I let off the gas or speed up or turn it will stop until I stay at a constant speed. I have since replaced the jet pump housing to see if maybe that was the issue. And it still makes the vibration. It is very slight, and I wouldn’t notice I guess if I didn’t have another of the exact same ski to compare it to, and I also replaced the shaft and bearings in the other ski with the same upgrade kit. The only thing different is the impeller. So I’m wondering if the impeller is the issue and is that something I should worry about ? Thanks in advance for your input or anyone who reads this.
@Sea_Doo_Life_175 күн бұрын
CLEAN DESIGN when will it be available??
@glockednloaded13175 күн бұрын
now
@discoverpigeon6136 күн бұрын
Hi I am Pakistan Karachi I am working Jetski repairing for Karachi Pakistan I need job
@AchikSarih6 күн бұрын
❤❤❤❤
@AchikSarih8 күн бұрын
Merci beaucoup ❤❤❤❤❤❤
@AchikSarih8 күн бұрын
Merci beaucoup ❤❤❤❤❤❤❤❤❤❤
@AchikSarih8 күн бұрын
❤❤❤❤❤❤❤
@kilo233010 күн бұрын
Anything for a 230 hp seadoo switch?
@gamerset19614 күн бұрын
Do you have a tune for a vx-c the other way around ? So that it doesn’t do 45
@douglasbonilla843516 күн бұрын
Didn't work ..My RPM arpund 8000 top speed 74mph😢
@marinejunkies962518 күн бұрын
How easy is it to remove the bolts and change the ecu over please show this in the video
@evansmith862119 күн бұрын
$340 damn
@AVS3720 күн бұрын
If you buy a kit stage 3 and a compressor wing r4, will the firmware from stage 3 be suitable?
@hezekiaB24 күн бұрын
Not shown: getting to the bolts to remove/install the ecu is nearly impossible
@marinejunkies962518 күн бұрын
Did you change yours?
@MikeLJ-ku7ovАй бұрын
There is a interview with Mike Adams on Brightion TV you’ll know what really happened
@orcryderzАй бұрын
I don’t care what anyone says, 85 on a jet ski is flying
@user-bv5iw9on8eАй бұрын
🇰🇾💯
@dutcher5172 ай бұрын
So we can’t install tunes with BUDS? That’s disappointing.
@danav33872 ай бұрын
Can this be tuned? Is this just a speed over rode removed unit? What advantages are there it buying this unit?
@BeefSupreme82 ай бұрын
I wasnt expecting it to open like that once the engine started. I thought I installed something wrong lol. It’s loud!
@user-bv5iw9on8e2 ай бұрын
🇰🇾💯
@boxz19842 ай бұрын
Why is therena filter needed? Wouldn't that slow down air speed?
@joeb91352 ай бұрын
yearly license cost?
@nicdhunter76522 ай бұрын
Wow! 😮. That’s impressive
@cagsanozbek42102 ай бұрын
Is it ok for engine life just to use speed limiter remover ?
@Redrockat3 ай бұрын
Great Video thanks I like the new vacuum actuated Tial QRJ Valve a lot and I think it’s going to help that supercharger last much longer and aid with performance Specially the New Design Stronger Pipes 🙌 Jip the Boost Port Adapter is Also Well Worth snapping into Place Snugly 🌟 ⭐️ 🌟 ⭐️ 🌟
@bakerelectricextreme79793 ай бұрын
Does this new blow off valve mate well with the stage 3 Riva kit on the 2021 rxpx 300?
@cubahot13 ай бұрын
Why u guys dont have that same kit for my 2023 gp1800r ho.
@sydneyenginedyno82784 ай бұрын
can this be done to a 2019 310R ?
@Just_.Jeff174 ай бұрын
Real question is was gud for the FZR models?
@jamiehaskey62074 ай бұрын
Beast
@jasonmekush52804 ай бұрын
Best way to silence all the critics drive both of these to Bimini, i guarantee both would make it. I have 2 82 plush mph yamahas w riva parts. they always start and go wot or not.
@jasonmekush52804 ай бұрын
Not a bad way to spend 40 grand. amazing machines, love my 8700 rpm 21 gpr w lots of riva parts.
@matthewrobert28884 ай бұрын
Whats out for the 1900 ho i just bought one and was wondering if you guys have anything
@rivaracing84683 ай бұрын
We have quite a few parts & accessories that fit the new 1.9L models. You may find them using the 'Shop by Vehicle' tool on the home page of our website.
@matthewrobert28883 ай бұрын
@@rivaracing8468 thank you very much I will check them out and do you know if these parts void the factory warranty?
@RVC84 ай бұрын
Max MPH
@rivaracing84683 ай бұрын
Our Limited Edition models utilize our Stage 2 Kit, which runs in the mid 80's on premium pump fuel.
@TwoOhJuan4 ай бұрын
Sickkk ❤
@frankykei1004 ай бұрын
Woo~80MPH=128.7km/h
@JDsWaterWorld4 ай бұрын
Nice! Finally a Kawi video😎 What was the fuel level? So would adding the Riva waterbox and cold air intake provide any additional upside? Are you concerned at all with valve float at the higher rpm? Not sure if you can answer this, but what is the total ignition advance that is being run on this stage 3 tune? Thanks!
@JDsWaterWorld4 ай бұрын
@@ears7589 do you have an exhaust filter bypass? Was that 10-40 synthetic?
@JDsWaterWorld4 ай бұрын
Ok nice, that’s pretty hot temp- I believe alarm comes on at 330 deg. I’ve heard mixed reviews on using the thicker 20-50..but have not tried it myself. Thanks for the replies
@rivaracing84684 ай бұрын
Fuel level 1/3 tank. Waterbox & Air intake produce acceleration but no additional top speed. No issues with valve train at this RPM. Ignition timing is very safe for use with our stage 3 pulley.
@JDsWaterWorld4 ай бұрын
@@rivaracing8468 thanks for the reply 👍🏻👍🏻 I am considering swapping my competitor tune for a Riva tune, and that sweet K3 pulley.
@Bubbabui455Ай бұрын
@@JDsWaterWorld hope you made a video? If not like to see it 😎
@LifeBeginsOnTheWater4 ай бұрын
Very impressive!
@JDsWaterWorld4 ай бұрын
Very cool, but would really love to see some videos of the new Riva parts for the Kawasaki Ultra 310…hard to find any videos of that K3 pulley! 🤦🏻♂️
@JDsWaterWorld4 ай бұрын
@@ears7589 are you running stock valve train and stock pistons? Is that number with the tune and pulley alone, or do you also have a the Riva ride plate and the solas depitched impeller?
Ай бұрын
Mine does 75mph with just the international tune seadoo spec
@barryschwingel85634 ай бұрын
How much for kit?
@snakedudemarosfoi19624 ай бұрын
I think they only made the reflash
@JDsWaterWorld5 ай бұрын
Great video, I really wish there was some content on KZfaq featuring Riva’s new product line for the Kawasaki Ultra 310 Jet Ski..you guys have some awesome new Kawi products, would love to see some video content on them! 😎
@sebastian88795 ай бұрын
windows lo. so there is no Mac version ?
@carlosjoaquim19215 ай бұрын
I have the Riva speed control override module already. Do I need to remove it to install maptunerX??
@user-bv5iw9on8e5 ай бұрын
Nice ski🇰🇾💯
@anythingadrenaline45155 ай бұрын
Anyone know who owns this? Or know where I can get a limited edition FX or GP?
@jaredhays29475 ай бұрын
Any specialty tools required for removal and installation?
@rivaracing84685 ай бұрын
Yes. We offer the tools through our website. They are listed in the installation guidelines that come with the coupler kit. Here's the link to the file: rivaracing.com/.../download/file/4691/product/84062/
@caracasbistroАй бұрын
What is the price ? I have Yamaha 2024 vx cruiser this work for me ?
@latunguleyАй бұрын
I have a 2014 fx svho with only 32 hours run time. You guessed it! Yes the timing chain flew apart. Was garage kept for years until I found it late in 2019 and tried to help the original owner have the engine replaced by Yamaha. No luck spent countless hours on the phone. Failed the good will. This is wrong. I was told maybe Riva could help out. If I trailer it down to Florida from Pennsylvania
@strvph646 ай бұрын
Very much looking forward to your yami 1.9 ho stage 1 kit!