Or how to unlock patternlock in samsung a224g without data loss

Thankyou it worked. Can you tell me code to open engineering mode in Samsung A224g

عمل رائع بدون اخطاء وشكرا لك

That was quite the fix good job.

good job on troubleshooting and finding out what was wrong... you rock brother.

Wow .. 5 opto's??!! 😳 Great video showing how to troubleshoot and fix, with explanation. Thanks for sharing this experience. Not all faults are easy to find/repair.

Do you have link to the pwm board you bought ?

Cool repair, Youness!

I bought a similar solder from Ali Express after seeing you use it in the past. Came in handy when I had to solder and new plug on the oxygen sensor for my car. The oxygen sensor wires are stainless steel.

My TV suddenly showed up two notifications, full memory and account action required, Google uninstalled the applications and just left KZfaq. I went to the account action option and asked for a password, but when I did, Google sent me the recognition to my cell phone so I could know. Yes, it was me and I accepted it but the TV asked me again for the password and it did so often I had to reset the TV but when it was reprogrammed I got the same notifications again I watched your video and I did your process same model but different serial 7G2021J5H05104 download the file from the hinsense website I did your process as you do but the upgrade was installed twice for me when it finished the second time it turned off it didn't restart the screen went black and it won't let me turn it on anymore I disconnect for a few minutes and turn it back on but only the red LED remains on. Any solution

What is the emergency code please tell me

If the read / write / verify is bad on the memory chip then you can check the voltage the CH-341 programmer is providing, it might be weak. In that case just feed external voltage 5V or 3.3 V or whatever the chip need directly to the programmer from your bench power supply.

Samsung panel is very weak...

3 red light ?

What temperature soldering iron did you use to melt the soldering iron on the motherboard.?

I'm a little confused. Can we just replace the cable rather than do this tape method? Would it work?

How can I do this

kzfaq.info/get/bejne/l69orNWQrNDJlHk.htmlsi=R6FSNpTkqP8G5Bd6

Use ps2 to hdmi converter in ps3. Watch some indonesian video.

if a customer says to me it's just a fuse issue, I give him a fuse, and I say if your device burns or explodes, don't come back to repair it

😢just cut the ck lines only

Thank you

After taping it works but the problem comes back again after couple days. What would you do in this situation?

Thank you so much

Hey, where can I find the replacement piece?

i like the video ,but i dont get why covering with tape/cutting the lines makes the set work? can you explain ?

thank you very much for the good tutorial sir..

Thanks sire, that's sure worked 🔥

Hi have same problem with my noco can i send it to you ?

Je crois que tu as oublié la petite éponge à l'intérieur ... mais bravo pour le Job ! Excellent 🤩

Khoya fen sakn?

Hello, on my Samsung TV I have no voltage on capacitor near ribbon cable on mainboard. When I disconnect ribbon cable and make a bridge on the 2 points at the top right corner on mainboard I have 17v on capacitor. What could be the problem ? No shorted capacitors on drivers panel. Thank you for any help

What size diode is that?

Forget my pin code Samsung Galaxy A14 airplane mode

Legend. Ty

LEDs in these TVs are designed to die after 1-3 years..since leds are supposed to last 20 years, manufacturers use downgraded leds to rip off consumers..much like the cascadent bulb story.

Man, was about to throw this TV out. You’ve saved so TVs. Mine is working as good as new. Thank you!!

Where can i find a replacement battery for the gbx75?

So to fix you just removed the capacitor? Didn't replace it?

Exact same unit I had last week, same problem - both belts. Easy fix. It took me longer to figure out how to open it. Make sure you have an Audio CD laying around to test with!!🤣🤣🤣🙃

Another good repair. Well done...

Tengo uno igual pero no regula +15 V y -15V esta dañado un smd 1Bt y nececito el schematic los modulos de poder estan bien pero el preamplificador no finciona

I love my unit...only had to replace the battery once and they're cheap. Only complaint for me is the fact that I can't get many radio channels, but that's not much of a surprise considering that I live in the Sierra foothills...

great work

Hi I have same wave radio for repair it's working but d problem is cd doesn't work tried changing capacitor but sitt d Sam what could be d problem?

This worked for me also. Thank you!

That’s why there’s only 1 year warranty because they’re not meant to last

They are not fuses, they are ferrite beads. They can act like a fuse just like a 0 ohm resistor can. They are designed to filter high frequency noise. You tested for ground at that cap, why would you replace with a ferrite bead? Also you should invest in some smart tweezers. You could have grabbed that cap after it was off and measured its capacitance and esr. It would have saved you hours and 3 driver ic’s.

Hi bro by mistake my czn water spray on my controller but i did not know he spray water on my controller i play games without any problem after some time some button not working r2 psbutton i see water only on buttons or little drops on film i clean it ps button start working but r2 not working after some time ps button stop working charging light change to red but everything working prefect touchpad motors joystick charging but it does not charge with wall charger i order new film and put the controller in the daraz after two days when i plug it with the cable it is not working or charging no light come can replace conductive film fix it. It clean it reset it but not working

How do I know what diode to buy. I’d like to order some assortment of diodes