first step after using test peice is to doble check all faces clean . the check again . I seldom have had to adjust a micrometer despite the fact they are used often and often not treated well
@flodgey10 ай бұрын
Amazing camera work bud, totally didn't give me a stroke.
@schuelfish10 ай бұрын
Did you not read the description? This was done 7 years ago with a go pro 🤷♂️
@flodgey10 ай бұрын
@@schuelfish I know, I was just joking around, sorry if that came out bad.
@schuelfish10 ай бұрын
@@flodgey you got a laugh out me 👍
@arumugamm140011 ай бұрын
Our mic 0.25 positive err, Thankyou so much sir
@rsitch1 Жыл бұрын
Great to know,thank you….Bob
@ryanmyers28772 жыл бұрын
Thanks for the help! Needed to measure my cylinder and piston on a quadzilla 500 they were out beforehand.
@schuelfish2 жыл бұрын
Awesome!
@axa.axa.2 жыл бұрын
Is this also valid for Brown and Sharpe?
@schuelfish2 жыл бұрын
Yeah they are all pretty much the same.
@HomineDomine3 жыл бұрын
Thanks a lot for upload this video, dear friend. I need this for calibrate a micrometer Mitutoyo. Greetigns from Chile.
@harehare2803 жыл бұрын
Great job thank you
@brianjohnson2173 жыл бұрын
Thank you very much for showing how to repair / reset a micrometer. I dropped mine and couldn't get the calibrations back in the original position. I didn't know the procedure on pulling the barrel out procedure. Can't wait to get in my workshop in the morning and cure the problem
@Series82173 жыл бұрын
Thanks for the great video. I was able to calibrate my cheap Alltrade micrometer using the technique you showed here.
@jurdyswisher54603 жыл бұрын
GREAT video. I just took over QC at my company and we had so many mics out of service because of barrels were off and I guess no one took the time to figure out how to fix them. This was HUGE help thanks!!
@longboard3ng2 жыл бұрын
Same! This vid helps tremendously
@TheGeezzer3 жыл бұрын
W⭕W this was very helpful and helped me celebrate my fussy Xmas present mic...it was 3 microns out on the vernier with a very stiff sleeve. The thimble removed easy and I managed a good zero-line-reset. I collect quality mics, have about 15 of em, all B💥NG on accurate to the micron or 10thou.
@christopherhasert68613 жыл бұрын
Had an issue with a customer mic. The zero was position 90 degrees down when i checked it. But when i saw how you popped the barrel off, I did the same to the mic I was working on and it reads perfect across the range. Just when you think you know something, you learn something new.
@lnna54624 жыл бұрын
I have one with the pointed spindle. One end is broken, how do I take it out and replace it?
@funnystuff25914 жыл бұрын
Great video
@salifti75344 жыл бұрын
Thank you very helpfull
@BigParadox4 жыл бұрын
Thanks! I just bought a micrometer and I did not understand that small part of the key, the one you used first, to make the first adjustment. Now I understand it all. Thanks again!
@pauldiaz42734 жыл бұрын
Great video thanks!
@AsianBlackR35014 жыл бұрын
Thank you.
@zahidabbasi56145 жыл бұрын
Very good video regarding zero adjustment i like this technic. THANKS
@JasonTylerRicci5 жыл бұрын
I just inherited a vintage Browne and Sharpe that needs minor adjustments. Your video helped me do so
@unnalmudiumnanba49395 жыл бұрын
Tq useful msg
@brucewilliams62925 жыл бұрын
Thank you so much! Just bought a used micrometer and its thimble was off by 15 thousandths from the digital reading. It's a digital Mitutoyo and it works the same way on the thimble assembly. I really appreciate the help.
@davidhershberger78995 жыл бұрын
Thanks for sharing this video. I am taking some machining classes right now. Watching this video filled in some gaps I didn't understand when reading how to calibrate a mic.
@pg64295 жыл бұрын
How to remove and correct 0.1 to 0.3 error in micrometer??? please tell me...