kid: be careful, I saw a tic toc where self-cleaning ovens burn out the safety controls and start house fires. me: silly you, I saw a tic toc hack where putting my blackened sheet pans in the oven they will clean up like new. 4 hours later, the oven is flashing an F5 code - apparently the temp control is hosed. The oven door won't unlock. Looks on tic toc for fix. We reset breaker after 5 minutes, nothing. We unplug the oven overnight, nothing. Today, I found your KZfaq video and unlocked my oven with the self-clean reset hack. BTW, the baking sheets look brand new. Thanks!

❤thanks so much was able to fix one of my stores

Where can we get Dust Mop Treatment Spry in India ? Thank you.

We have a Frigidaire from 2002. had a cracked cooktop and the dual element had burnt out. the new element did not have the same wiring. Your video helped me realize how to test the new element and figure out that the high limit switch was different. I think I got the n and l1 backwards or did something to the warning element, but it seems to work. There were all kinds of little springs that kept the elements off the brackets. mine was really hard to work on slide-in-range, it was all I could do to keep the elements sorted out and get it back in... and to top it off we couldnt find a glass cooktop replacement for the same model, but we found it rebranded and a different color/kenmore elite grey vs frigidare gallery white... we're ok having a black cooktop... as long as it works. the cabinets and floor were built around this, so it is hard to replace.

What's with the emotionless people in the corners of videos

Thank you for the video. I hope this works for me. I have the samsung NE59R4321SS-AA-00 oven. It heats up to temp when you turn it on but will not hold the temp. I have to keep entering the temp over and over to get it back up. I replaced the Temperature Sensor already and that did not work. Do you think this is the problem and I need to replace the High limit switch? Or could it be something else? Any help would be great, it's driving us crazy. Thank you and I look forward to your reply.

Hi! I’m having an issue where thermostat won’t reach to 68 degrees or above. I am thinking of troubleshooting it myself before calling a professional. Should I turn on the heater and let it shut off itself before trying to troubleshoot?

Not all furnaces have lights so no this video doesn’t help. We all don’t have top tier equipment. Junk videos honestly.

Thanks for your video. My burner element heat up once I twist the knob, but then quickly shuts down with the click sound every time. Please let me know if you know the reason and solution.

This is a long shot - I literally cannot unscrew the screws on brand new oven. Any ideas?

Again large amounts of coal dust

Any tips on the best most efficient way to clean the offices at a coal mine. Lots of coal dust.

Did not show how to repair an existing but only to replace, so a misleading headline.

Next time, dont talk over more than 50% of the noise example. Just let the bad noises play for us!

Good day I have oven kelvinator and breaker trip from Time to time and today I see the oven and refrigerator connected in one breaker 30A

I love this channel

very nice edu

Thanks 🙏

Greetings. Thank you for your videos. I have a GE Profile PCB909DR1WW glass top that is probably around 10 years old at least and intermittently will not have ALL the elements working. They could go dead for a few days and without doing anything, they will start working again. The lights will come on, but no heat. Currently, it is working and all my connections seem intact with no wire issues that I can see. Ohms testing seems good. Any ideas as to what is causing this issue that has happened twice now? Obviously, will test again should it fail again, but if you have any leads I can address now or then would be appreciated. Thanks.

ALL of my burners are suddenly staying on even when the knob is off. Flipping the breaker resets the stove & it stays off until you turn on a burner. It seems unlikely that all 4 switches suddenly malfunctioned at the same time. Is there something else I should check? Is this a control board issue? Thanks for the helpful video.

Cool

lovely video sir

Eccellente.

As beginner should i start:What is elictricity,volt,amper etc.?

I flushed my tank last night (I'd been away for a few days, and had it set on "pilot" so the water wouldn't be Hot.) I temporarily turned on the relief valve at the time. I went downstairs this morning, and the pipe was dripping. It's still dripping tonight. If it ain't Broke...

Well done video. Didn’t waste my time with mucky-muck. Thank you for taking the time to impart your wisdom.

Worked like a charm

You need to read audio 📚

What about the length of the screw base? Is there a code for that? I ordered correct diameter but the length seems to be different. Thanks!

very good education

Also the sensor head flashes yellow and not red when it flushes

I have replaced the battery pack and tried 2 piston/solenoid assemblies and it is still letting water pass through in to the urinal without flushing.

Thank you I know how to repair regular toilets but now I know how to do these and it's a lot simpler than what I thought it would even though I kind of figured it was not as hard as I thought it was going to be either thanks for the information have a great night

Hi. My pilot lights ups, but the valve will not start blinking so that I can operate it....????

Recently I almost got died due to Electrical Switch Short Circuit. I lost literally everything I had in my Hostel Room. Physically I saved myself but I had almost 6 lakhs loss. On 10 march 2024 I wake up at 6 am I felt very cold so I turned on hot air giving small round heater and slept again for about 3.5 hours. When I wake up on 9:30 am another bed was fully burning from the underneath of the bed where there was switch. When I wake up fire was already getting big and big. Eventually I couldn't do anything and run out of the room and on panic state watch my room burning. All of the people got panic and they couldn't do anything either. Whole room got burnt. Nothing left Nothing. After that fire brigade came and controlled the fire. And Big Coincidence I am exactly 1st Semester student in Bachelor of Electrical Engineering at TU , IOE , Pulchowk Campus, Kathmandu, Nepal. So I am researching how was that big fire accident happened. i concluded these things. - there was a lot of burnable things like books and clothes near the switch due to short circuit fire ignite and it immediately spread out amongthings and started burning massively. - as I mentioned I used electric hot air blowing round heater fan for 3.5 hours due to over use for long time continuously short circuit happened. -i guess the ampere Capacity of the hostel was just 5 A. which couldn't hold the load -about 35 students live in that 3 floor hostel. there was massive electrical overload on that building electrical systems. -the wire, fuse, switch, wiring and entire electrical system was very old, because that house itself was very old. I guess they didn't change switch and wire for one time after the construction. Electrical Systems was aged. - before 2 months when I used that switch to charge my laptop the light of the room was blinking and blinking. I told warden of the hostel about the problem but he just ignored and said me to use another switch. that day heater was used in that damaged switch. As a Electrical Engineering Student I analysed everything of this biggest accident of my life. By all these things going wrong in electrical system of that room got burned due to Electrical Switch short circuit and I am baring heavy mental stress and losses

Is this reasoning correct? If u set gas oven to 350 and temp never changes but PREHEAT light comes on. Gas is not flowing and ignitor comes on. Check resistance and it is bad. OL on multimeter. I am thinking that since temp never changes except for heat from ignitor and temp is never reached, the temp sensor is sending improper signal to control board and board is not allowing flow of gas. Is this correct. Also blew some compressed air via bottom inlet to regulator and in closed position , no air came thru but in open , it did. Also checked for continuity in gas safety valve and it was good. New oven and it only lit a couple of times with a loud cutting off of gas which sounded like ‘WUFF’ I am trying to confirm my thinking is correct or not? I have to go pickup new temp sensor and install in couple of days. Display has thrown NO CODES whatsoever

Is the pad installation directional? I noticed that the dark spot (looks like a burn mark) was at the top in the video.

I’m just getting into working with electronics as a hobby, and this video connected so many knowledge gaps. Thank you for your clear explanations and examples!

Wonderful Video. Very Helpful Explanations. Thank you!

This was great, but mine NEEDS adhesive foam tape, the bottom of the door lifts up without it. And the video doesn’t mention what kind of tape you need to buy 😔

Any videos this clear and concise on how spring loaded check valves work? I've got one in a condensate pump (Liberty LCU-20s) that won't close. It would be nice to be able to see inside in order to understand what's going on better.

Much more efficient to put a jumper across the two safety switch wires to test if furnace works before removing a sensor

If you found this video helpful, let us know in the comments, and if you want to see our complete guide to test the compressor, capacitor, relay and overload protector, watch this troubleshooting guide: kzfaq.info/get/bejne/hLR0a61pyb7VemQ.html

Wow amazing explanation! It's a 3 in 1 video ! I have to replace the full lenght kit , whats the name of it I can found it online? Thank you , it will make me save hundred dollars 🤞🏼

Shouldn't you wrap some Teflon tape around the pipe threads?

Will this work for a 12v/24v mini fridge?

At 1:03, do I even have to remove the p-trap ? Can i just loosen nut underneath drain and slide it up and slide the new drain down ?

I think our plumber may have broken mine. The aerator is just loose and no water comes out of it anymore. The water comes out from behind the sink now. It’s just stuck there, can be rotated a little bit, yet it can’t be removed.

My faucet doesn’t have mounting nuts. 😩😭 Each supply line goes into the faucet through skinny, little pipes.

What are the reasons that typically makes sensors and solenoids unresponsive?