Just bought that saw and used for several hour in the rain. Manual melted. Thanks. Very large oak tree is on my friends house. Bringing a made in West Germany Stihl with a 20" bar tomorrow. Plastic Dewalt would not be my go to but works with a sharp chain.

I cannot get the wi-fi to accept my phone number . Cannot complete registration. Wi-fi will not work.

Super very nice video ,thanks!!

What about the oiler? I bought a different model Dewalt electric chainsaw and in a few months the oiler no longer worked because it was very poorly designed! What good is a chainsaw without an oiler?

Explained perfectly. Thank you. Helped me out much

Don’t want to piss no off but you don’t need to use NOALOX anymore for aluminum wiring for like the last 30 years we perfected the aluminum alloys in it. It’s not like how it was back in a day.

Worst air conditioner I've ever owned. Doesn't operate when it's hot outside and you actually need it. The first one they sent broke in less than a week, compressor went bad. Second one compressor hasn't gone bad, but the compressor shuts off after the unit runs for about 10 minutes and stops putting out cold air. So as an air conditioner it's Useless. Plus it said online that it's a 12,000 btu unit. When it arrived, the sticker on it says it's an 11,500 btu ASHRAE and 7,400 btu SACC. Which means it's only a 7,400 btu unit and is a piece of Junk. Don't expect to stay cool with this thing or you will die from the heat. I hope this company burns to the ground and goes out of business.

Great video. Much easier explained than many of the others I looked at when I first bought this thing which I really do like. My poor ole Stihl doesn't get used as much anymore...

Where’s the video you promised on using the Graco sprayer?

What do you do with the white wire that comes out on the switch???

Main shaft fits securely in bike. The seat and spring shaft rotate and twist as I ride. This doesn't seem normal or safe. Defective or is there a way to fix?

Not shown it in operation.

What if I don't have a framing nail from the 1930s?? LoL

Thank you!

wrong..... the best for ICF are IPEX ICF boxes 1,2,3 gang........ and transverse running wire need to be deeper into EPS, otherwise at risk with Drywall install... screws will penetrate. if put the wires about 2" deep into EPS, then the wires are not at risk.... kinda weird to make a 'special situation' recommendation as a 'professional' that are real makeshift seems quite lame, to say the least....

Useless video

Are any of these things code and insurance compliant yet?

I hope the landlord of our home that burnt down last week retains the integrity of the home in the rebuild

Manual says to empty oil after every use?

DO NOT COUNT ON THE TRIMMER TO TRIM THE EXCESS LINE AFTER A LINE CHANGE! I did like the video and the long line was sucked up into the head of the trimmer and locked the motor. Had to get a replacement head as it was unfixable. Trim excess line before use after line change.

Im from Michigan's upper peninsula and if you burn pine in your wood burner you will have creosote build up and chimney fires!

Hi, question, I need to cut 1/4" off my blinds. Can I cut just one end? or do I need to cut 1/8" on each end? Also, I have a sliding miter saw, is it better to chop down, or slide? thx!!!

I had been wrangling with getting my new chain to stay put. Your video made it easy. Many thanks.

How do you adjust the tension on the Zoom Shock?

Thank you so much!!!

Omg thank you

It would be nice to know your region/length of heating season to think about your cordwood usage, and the temps in your house when heating.

I saw this video when I started working as an electrician 6 years ago.

Straight to the point ! Thank you

People... don't double up Neutrals in any panel, let alone when you have tons of spots for each wire to be individually terminated. It is likely not code compliant in your area and frankly bad practice. Like... what benefit was there to do that here? Saving cutting a few wires a wee bit? Makes no sense whatsoever.

How can I get this dc motor

a bell chamber is far more efficient and cheaper to build.

The blade winch for the snowsport plow bolts right up to the Rediplow

what came first Snowsport or Redi Plow

Ffs why put the cover on before tightening. Made a right meal of that mate.

The rmh people claim you'll use 1/10 of the wood compared to a woodstove. Based on what you said that's not even close to true.

It’s a pleasure to watch a Professional. Thank you for the video.

Nicest and cleanest build ive seen so far.

Has anuone ever use a sand battery storage in the bench???

12 Gauge wire for smoke alarms?

It's so clean.

I am still a bit new to wiring a panel, but have done a ton of research. Isn't the clamp on the service entry cable, rated for the flat cable, and not the "round" cable?

Dose urs blow out cold air when on dehumidifier?

Thank you for making this video!!

Plz give me purchase link sir

Thank you so much. I had a professional come out but blinds didn’t for inside mount but were to small for outside mount. I didn’t know how to give them the proper measurements. I knew to make a mark but wasn’t sure how to do it. Spot on. Thank you ❤

So do I need there receiver or if I already have a front receiver is that all I need ?

i don't understand how to buy the carbon tapem i clicked the link but i don't understand

Actually the temp just on the barrel can reach 700 degrees. The mass can heat up to 150 degrees. If it is assembled correctly. Check out the Fouch FAMILY on you tube. Also you will burn approximately 1 to 2 cords of wood. Also if this system is done right you won't have to burn all day either. Because the mass will provide radiant heat for another day without starting another fire. Also you only have to clean out 2 times a season.

Good review, but props on the vid as well, with the drone footage.