You failed to spin test the bearings. You failed to attempt to clean out the piston rod bottom bearings and the crank bearings on either side of the damaged piston. High chance of metal filings in those bearings.

Obknow this is a 2 year old video, make sure you test the oil pump for the oil injection, first full tank of fuel mix it at 50:1

Free advice, remove the seat , gas tank, that stuff needs to come off then the airbox you'll see wut i mean when you take all that other stuff off it opens up so your not fighting with no room to take the engine off

When you took your 2017 sportsman to the dealer to have heat shield installed, how did dealer install heat shield did he have to remove rear cab to install heat shield? I purchased a kit for 2016-2017 but can not get metal heat shield over exhaust pipe, might have to remove rear cab thanks Danny

Looks like fun. Quite a bit different than riding a sled.

Inches or mms?

WOW! Always Good When You can get Up and Laugh it Off! Glad that you were Ok! Do You wear anything like chest protector? Or Shoulder Protection?

Going in a week. Whats the best place to find good snow around there? Most of what I’ve seen looks pretty tracked up unless you go right after it snows

Nice vid. Thanks for info. Im going deep soon and purchasing a snorkel kit for my 2023 sportsman 570

Great video! How many hours did it take to rebuild?

Once the sled is loaded and ramp is in and strapped in how do you strap in the sled with the ramp blocking the tie down latches on the truck?

This is exactly what i want to do but reverse lol, did the skid bolt right up once assembled?

Nice man! With woods like that no wonder they make bark busters. I wish I had this kinda riding in socal!

Sweet bike!

Thank you

The side look😂😂😂

Looking to put one of these on my rmk. Did you only have to buy rails and wheels or did you need new shocks as well

Needed all that work after only 4400 miles?

How did you clean the old sealant off case before reassemble?

This video sucks. I wanted to know how to adjust it underneath. How to adjust the tie rod to move it in and out and it has nothing on that. There's no video that shows what he is doing underneath. It sucks rocks!

What is the part number on that shield? I need one

Gotta come see keweenaw county U.P. of Mich. See copper harbor and all the trails. Winter or summer machines.

Good video. It's good to see that all my frustrations are shared by all with the model, lol, but like anything, the more you do the work, the more straight forward, etc. I have to say, pulling the winch was a lot easier than when I installed it! so it wasn't as big a deal as I thought. I like the idea of using a pump to fill the diffs, better than the "easy packs" (Amsoil). I always remove the tires when I do the diffs, and keep the atv level. The jack can get in the way of the drain but a little extra mess is worth extra access and am always finding ways to make it work better than last time. Again, good real world video. Thanks

When you’re rotating the crack by hand you have to rotate to the left. Counter clockwise.

I've been riding sleds in the UP backcountry for years. Bought my first dirt bike this spring, and hope to get up to ride the trails in the next couple of weeks. Super excited!

How much longer is khaos shock than rmk?(front track shock)

I strongly suggest that you remove the outer wheels on the anti stab kit and cut the axle that holds the outer wheels. Even if ice age are top quality it is really easy to take a hit on one of the wheels that bend the axle and in worst case scenario breaks the axle - and it is a perfect way to destroy a weekend when you finding that you are standing on the trail three hours away from everything with a stab kit that's now only bolted on one side of the rails...don't ask me how I know that. 🙄

Nice work! Did you notice quite a difference when you installed the Khaos conversation kit (Shock extender and limit strap) when it was still at 155?

That was a fun trip!

Hey could u send me your email? I'm having weird noises when I try to start up it sounds like the starter isn't engaging properly and when I finally does crank up, it idles for a second b4 it seem to get in in bind and shut off. The starter is new

Mine has it, I'm pulling it off.

perfect . I love it. great job just lost the motor in my 600 rush last night. time for a tear down with my son.

I like it

How do you set up your power values in your engine

How do you set up your power values in your engine

How do you set your power value when putting it on the engine

Is that a 5.5 ft bed? Or it's full size bed ? Thanks

Looks beautiful out! Bet it was a fun ride.

How do you get spacer off the shaft after you take the brake rotor off to slide the chain case cover off. Thks

Im starting to like Polaris!

Earned a new subsciber i want to rebuild a 600 cfi in a 2014 polaris indy 800sp frame

I loved working on the sled with my dad!

So you didn't show how you got the cams back in the head with the timing chain, which is maybe the most important part putting it back together, that's where I am at now. I don't seem to be able to get the cams and chain back together

Thanks for the video

Love the video, I’m going to be doing same thing with mine

I'm eyeing a 2012 Rush 600 that has 10K miles on it... Might have to do this 😅

I'm going to put a straightline performance on my 850. When it's on I'll be riding in the middle of nowhere on private property. If I go ride trails I'll throw the stock can back on

Do you prefill the cavity of the crankcase where the crankshaft gear meets the water pump gear with any oil?

My favorite trails. Nothing like a grown man beating the shit out of a outlaw 110