How does the board come out? Does it just lay there? Clips? Thanks
@KentuckyPatriot177614 сағат бұрын
Nice! No crossmembers or anything below the filter. I hate it when the engineers do that!
@joshchandler64772 күн бұрын
It works with 2024 screen black out too
@LaminarBubble5 күн бұрын
How do you know the clockspring is the problem? I am looking to install a raptor wheel on my 2015 platinum, but some of the buttons don't quite match. I was hoping to swap the individual buttons, if that is even possible - is it? If not, Perhaps I will consider using the raptor buttons even though they are marked incorrectly. Is it a button issue or definitely a clockspring issue?
@ezkabob65288 күн бұрын
Thank you..that was helpful
@HeartlandRebuilds2 күн бұрын
Glad it was helpful!
@osvaldoj96788 күн бұрын
I have a 2023 hybrid xl working perfectly, the only issue is the radio sync 3, it downloads the update but never installs them .. do someone have the same issue?
@will299310 күн бұрын
My battery was still good, but after reading you should be using an AC Delco (or equivalent) agm, I decided to replace it with one from the Chevy dealer. Well I don't know what that stupid battery did to my volt, because it threw 10 million check engine lights, and now I can't charge the main battery . Why.
@ConnorPhillips-lt2xt10 күн бұрын
Thank you! This video rocks
@HeartlandRebuilds2 күн бұрын
Glad it was helpful!
@danieldepaula52311 күн бұрын
I cant understand why Ford is blocking these functions. I have enabled the eco/sport option and windows control by the remote control. So, everything is in there. Ford must enable all of these option for an extra. Does not make any sense block them have you tried to talk to Ford in the US? Thanks for sharing. Greetings from Brazil
@joshuachikumbindi379513 күн бұрын
Great video,Thank you,amazing how you’re to work with one hand whilst filming.You’re gifted my brother again thank you 🙏🏿.
@HeartlandRebuilds2 күн бұрын
I appreciate that!
@bobjamison188914 күн бұрын
I have a 2016 F150 and I have a complete failure of all buttons on the steering wheel and the turn signal. The only function that works that is controllable in the steering column is if you turn the wipers to high, the wipers still work. Replaced the clock spring using your great instructions and there was no improvement. What is the next thing to try?
@sanbelaez7 күн бұрын
Im having the same issue
@bobjamison18896 күн бұрын
@@sanbelaez I finally fixed the problem. This video was very helpful in removing the steering wheel and getting access to the Clock Spring and Steering Column Control Module. After replacing the Clock Spring the problem did not go away so I replaced the SCCM which did resolve the issue. The unfortunate thing is the Clock Spring is $200 and the SCCM which includes the Clock Spring is $350 so I wish I woul dhave just replaced the SCCM at the beginning.
@Willy_LGM16 күн бұрын
Thank you for the helpful video!
@HeartlandRebuilds2 күн бұрын
You're welcome!
@olivierbastet387416 күн бұрын
Great stuff, thanks! What about going a bit further and change cruise control to adaptive cruise control now?
@HeartlandRebuilds2 күн бұрын
That would be cool!
@Radar8826917 күн бұрын
Still need to program the key to the car.
@deannafairley170918 күн бұрын
Thank you for the short and to the point video!
@HeartlandRebuilds17 күн бұрын
Glad you liked it!
@analogdesigner19 күн бұрын
Another excellent video, thanks!
@HeartlandRebuilds18 күн бұрын
Thanks again!
@analogdesigner19 күн бұрын
Excellent video, thanks!
@HeartlandRebuilds18 күн бұрын
Glad you liked it!
@garybial21 күн бұрын
Great instructions, right to the point with no unnecessary comments!
@HeartlandRebuilds18 күн бұрын
Thanks!
@jerrisn21 күн бұрын
What key machine are you using? I was told they need to be "laser" cut by the dealer.
@HeartlandRebuilds18 күн бұрын
Defu 368a. I've had it a few years, still works great. Bought it pre-COVID for $110 on eBay. There's similar models available for about the same price, or a little more. The "laser" key cutter is just a vertical mill.
@jasonmoquin22 күн бұрын
Interesting. Personally, I would like mine to be a little louder and would really like an option to change the sounds. There are a number of young kids in my area and this feature might help them hear me coming.
@HeartlandRebuilds18 күн бұрын
The only time my car wasn't making noise was when the air conditioning was turned off.
@soybeaner8524 күн бұрын
Can you add adaptive cruise control to a 2024 XL with Forscan? I want it so bad. If not what do I have to add to get that ability?
@HeartlandRebuilds18 күн бұрын
There's been a few people who added it. You'll need the front radar unit, some wiring, and a few other things. May be cost prohibitive though.
@johnheath430524 күн бұрын
Did you do an oil cooler?
@HeartlandRebuilds18 күн бұрын
No, just the transmission cooler
@mariebosoumabeugre242626 күн бұрын
Mine keeps going back to step one I tried for at least 2 hours
@rodneyhampton338426 күн бұрын
Do you see this clock spring as an issue more than the 2 switch packs (cruise, radio)? Also great idea on the cleaning rod to pop the airbag off.
@HeartlandRebuilds25 күн бұрын
Yeah, you would think a button would go first, not on these trucks. You could also use a small Allen key or something like that. The cleaning rod I used was almost too big.
@omaralimujah247526 күн бұрын
Great close-up shot. Very clear instructions. Thank you
@HeartlandRebuilds25 күн бұрын
Thanks
@kevinmosser5969Ай бұрын
This was awesome, no stupid intro just what I needed without the fluff….THANK YOU. It worked perfectly, got the clock spring online from Village ford or something like that since it was $75-100 cheaper than my local dealer.
@HeartlandRebuildsАй бұрын
Thanks. Glad it helped.
@PapaShango619Ай бұрын
Gonna try this. My company started using Ford Mavericks for work and I gotta lay down at least two hours of drive time a day. So I need some music to pass the time.
@YukonHawk1Ай бұрын
You should bullet proof it. Look that up on KZfaq and you find out people mod it with a bolt head so the plastic doesn't wear down
@HeartlandRebuildsАй бұрын
I'm going to do that. It's already showing a good amount of wear without the bolt
@MrA1277Ай бұрын
Awesome, just programmed my spare key. Now have a 3rd spare for under $20 woohoo
@HeartlandRebuildsАй бұрын
Nice
@dyllonhughes6338Ай бұрын
Not detailed enough on how to take the rod into the small holes to pop off the air bag
@HeartlandRebuildsАй бұрын
It's spring loaded, push something small through the hole until that side of the airbag comes loose, repeat on other side.
@wwsoapbox6921Ай бұрын
Looks like way more trouble than it’s worth.
@HeartlandRebuildsАй бұрын
It wasn't too bad, but not really necessary to have
@midwestmasonrystlАй бұрын
Bought my 2018 with 20,000 miles. 70,000 warranty…at 74,000 I had to put a new motor in $5,000 86,000 transmission went out. $3500 20,000 miles later it’s going back for transmission a 4th time. Still owe 7k on the car and I’ve spent 8500 on repairs to a car with 106k on it 🤔 Absolutely ridiculous..for would not budge on price of the engine only being 4k over warranty. FORD motor company. Your customer service sucks just as bad as quality of Ford vehicles lately 🖕
@HeartlandRebuildsАй бұрын
The head gasket on this 2.0 Edge started leaking a couple months after this video was made. Ended up needing an engine as well, also outside of warranty.
@ericgalvan358921 күн бұрын
@@HeartlandRebuilds Did your Edge have the original coolant when the head gasket started leaking?
@HeartlandRebuilds21 күн бұрын
@@ericgalvan3589 I replaced the coolant when I bought the vehicle, however I believe it was having problems before I bought it.
@idiSpatUzheАй бұрын
confirming. I used router to widen Kobalt's bat grows. Works just fine on my Kobalt and on Snapper. Using BS charger and it works just fine. I'm using BS batteries on Kobalt hand-held blower and Kobalt bat - on Snapper mower. On a separate note, Lowes Kobalt backpack blower took BS battery without modifications out of the box. So there may be other dual brand tools that need no modifications. Though backpack blower required a lot more juice than a 2ah bat can deliver and needed a bat change every 8 minutes.
@HeartlandRebuildsАй бұрын
Greenworks, Kobalt, Snapper XD, Masterforce, Victa, Stiga (old ones), Greenworks Commercial, Briggs & Stratton, etc. Globe Tools Group batteries are interchangable. Just make sure the side slots are cut and similar voltage.
@brianmullican7191Ай бұрын
Thanks for still helping people. I have a regular gas burner 2024. Based off the comments, seems like a common problem across year model and trim package. It's a Shame Ford leaves it to good hearted guys like you to show us how to put a bandaid on their software glitch. Mine didn't start acting up until it sat in the 92° sun in Tennessee.
@HeartlandRebuildsАй бұрын
Thanks. Mine did it the second day I had it. Can't stand going to the dealer, so found a "temporary" long term fix.
@tfriesen3866Ай бұрын
4:00 My wife’s ‘17 Edge Titanium (strangely same color) had the same issue with those rear door seals. Dumbest idea. I’m working on what someone else half-assed together myself.
@HeartlandRebuildsАй бұрын
I've seen another one with the bottom seals at the door falling off. There's a Ford TSB on how to fix it. Basically clean the dirt out, find some grip tape and stick it back on. Great area to hold dirt and start rusting...
@tfriesen3866Ай бұрын
@@HeartlandRebuilds that’s exactly what I did.
@MrAWorthy1Ай бұрын
I’m thinking of grabbing a 2015 tailgate with the tailgate step and swapping it out on my 2013, they should be pretty much 1:1 shouldn’t they?
@HeartlandRebuildsАй бұрын
They are basically the same. You'll need to replace the hinge if yours didn't have the step already. Step tailgate uses the torsion rod attached to the hinge to help it since it's significantly heavier.
@thomaseichstaedt4988Ай бұрын
Cruise control randomly deactivates itself. Can’t consistently get cruise control buttons to work. Hoping its the clock spring and nothing more. Thoughts?
@HeartlandRebuildsАй бұрын
Probably clock spring being flaky.
@MrOrthoclaseАй бұрын
Thanks for the quick video. Just got my Maverick after a 19 month wait. Living in a state where it's mandated by law to have front plates but they didn't put the mount on.
@HeartlandRebuildsАй бұрын
It's easy enough, just need a POM riveter.
@puddyrayАй бұрын
Very clear and helpful - thanks!
@HeartlandRebuildsАй бұрын
Great to hear!
@ting6091Ай бұрын
Would this work on my 2022 ford XL or no?
@HeartlandRebuildsАй бұрын
Yes. Every year Ford Maverick.
@zayne4876Ай бұрын
Will this for a 2016 Malibu hybrid? Very little info is out there. Thank you
@HeartlandRebuildsАй бұрын
Yes, process is the same. Transmission/drive unit is very similar.
@jojojordan55572 ай бұрын
Thank you for the video. One questions though: didn't you have to go through the gears before accepting the new level as accurate?
@HeartlandRebuildsАй бұрын
Yes I did.
@number1pappy2 ай бұрын
It's criminal that ford and other dealers don't recommend trans fluid change every 30 to 36 thousand miles. Both our car owners manuals say it doesn't need changed until 100 thousand miles! Unbelievable! This plus the fact that the trans doesn't have a serviceable filter is just asking for serious trouble.
@HeartlandRebuilds2 ай бұрын
Absolutely
@brentthull49352 ай бұрын
Question, did you have to clear a code for the airbag? I know everything is installed properly but I have a ligth.
@HeartlandRebuilds2 ай бұрын
You don't have to clear any codes doing this. If you didn't have a light before, then you may not have got the airbag wires plugged in all the way and the lock clips pressed in all the way. Check those first.
@letswalkinthewoods14622 ай бұрын
Do not us an impact to lower your spare tire.... You will break the crank mechanism for sure
@HeartlandRebuilds2 ай бұрын
It was a 1/4 impact driver. There's no way that would hurt anything lowering it.
@Curti5732 ай бұрын
Thanks for the video. Got my battery of 8 years changed out no problem. Amazing how much better AM radio sounds again!
@HeartlandRebuilds2 ай бұрын
It's weird how a low 12v battery on these cars will cause random electrical gremlins.
@Tool_vs_Tool2 ай бұрын
Use C channel instead of angle peoples, 100% better.
@HeartlandRebuilds2 ай бұрын
Definitely. If I ever get in there again it'll be with C channel.
@TeamPsaradelis2 ай бұрын
Thanks for an easy explanation and fix!
@HeartlandRebuilds2 ай бұрын
No problem!
@brentthull49352 ай бұрын
Did mine last night, went as planned. Thanks
@HeartlandRebuilds2 ай бұрын
Awesome!
@ernesto73732 ай бұрын
DUDE thank you!!! Saw another video that didn’t work for me (I only had 1 fob) and bought 2 more oem refurbished ones for $53 each on eBay and $110 and this video later and I have 3 functional fobs now! 👍🏼 For anyone doing this and having an issue, you HAVE to wait the 10 minutes (x2) to do it. I put a timer on my phone and did the door open and door close to light up the screen again after 10 minutes to have the proper message show up
@HeartlandRebuilds2 ай бұрын
Glad I could help. Super easy, just takes a little time.