It's a local charity car show event. Race for 100 feet.
@berardoferrari5 күн бұрын
now i can clearly see where the water is coming in from the bottom of my dash!!!! that large metal brace must be cracked or rusted.
@jose.ramoscaban8 күн бұрын
Mine melted with these crazy heat waves lol, im ordering mine today. Thanks!
@BasinMotorsports8 күн бұрын
It's been crazy hot this summer.
@CalebBohanon10 күн бұрын
I can't believe that kid did all that damage... What are they feeding them down there
@BasinMotorsports10 күн бұрын
Sugar. Lots of it...
@joseojeda432213 күн бұрын
Can I do this on a 2015 versa?
@BasinMotorsports13 күн бұрын
I'm not sure what is available for the later generations of Versa. Check eBay or some classifieds for what is available for the 2015. You can swap assemblies.
@kevinhohne788913 күн бұрын
Important: Only works if the pressure on the hood (location of the louvers) is lower than the pressure in front of the radiator -> e.g. close to the windshield, the pressure might be higher, leading to even worse cooling capacity
@ericervin477814 күн бұрын
Where did you buy the cover? This is exactly what I need. The bezel for my 03 Z06 is cracked.
@BasinMotorsports14 күн бұрын
I have two different videos for the HUD bezel. One part is from AMT Custom Designs and they have a website to order from. I also have that part for sale as I took it off after making the video. My second video uses a bezel from RPFC5 on eBay. He also has a website, but last I checked eBay was cheaper.
@ericervin477814 күн бұрын
Thanks, man!!! This is exactly what I need.
@anthonycarranza834216 күн бұрын
Does the smaller hole need to be plugged as well?
@BasinMotorsports16 күн бұрын
No. It's just a mounting hole. It's not open.
@anthonycarranza834216 күн бұрын
@@BasinMotorsports I don’t think mine had a mount it was just the bolt that came out but good to know man thanks for the reply
@anthonycarranza834216 күн бұрын
When I bought the car it had the bolt plugged into the hose on the crossover pipe. Do you think the smog pump was removed?
@BasinMotorsports16 күн бұрын
@anthonycarranza8342 It might have been. If it was removed from the engine, the belt would be shorter or the pump could have been bypassed. It's usually on the passenger side below the alternator. You might see if it's there on yours.
@SeanKing010925 күн бұрын
This saved me I’m just planning rn but this helped me so much on how I’m gonna go about my build
@markbuilds467426 күн бұрын
Or thos stock fans or aftermarket?
@BasinMotorsports26 күн бұрын
OEM fans
@fungussf27 күн бұрын
Thank you! Your tip for using the left hand to position the right bulb made all the difference in the world. It only took a few minutes using your technique and now I won't dread this task the next time I have to face it.
@BasinMotorsports25 күн бұрын
Glad it helped. It's a tough space to fit your hand.
@Magic_Toaster29 күн бұрын
they'll be about $30/gallon, but sure, why not
@jeffmcmillan281329 күн бұрын
Who sells em
@BasinMotorsports29 күн бұрын
AMT Custom Designs made the one in this video. I removed it after installation and then installed a bezel from RPFC5, which is still on my car. You can find them on EBay from RPFC5. AMT has their own website, and I think I put their link in the video description. I do have a separate video for the second bezel installation, plus a comparison between the two.
@cogent211814Ай бұрын
Video does not do them justice. Everybody should see them in person. They usually look like there's a lake and the mountains are floating in the distance.
@locomato11Ай бұрын
Where the speed gods play
@beep_beep_beepАй бұрын
At what temperature does a icm fail?
@BasinMotorsportsАй бұрын
Above 125C (257F) is what I could find.
@JadeOfHealthcareАй бұрын
How do I contact you for video content creator assistance!
@BasinMotorsportsАй бұрын
There is an email address on my About page unless you can message me on another platform like Instagram, TikTok, or Facebook.
@JadeOfHealthcareАй бұрын
@@BasinMotorsports I will look for the email or contact you via messenger. Thanks
@JadeOfHealthcareАй бұрын
Do you do video content?
@BasinMotorsportsАй бұрын
Yes.
@timweb1510Ай бұрын
Looks good man
@deanwinchester119Ай бұрын
Product works but you MUST do these things 1) 160-170 thermostat 2) *(VERY IMPORTANT) Get a tune where your fans kick on at 170 degrees 3) MUST use in distilled water ONLY!! 4) Burp the car so theres no air pockets
@bsalabaoАй бұрын
How do u take off the molding above the door. The one attached to the body?
@BasinMotorsportsАй бұрын
There are screws on the underside of the trim piece, then it unsnaps from the car.
@sassyravАй бұрын
My 2012 JCW Mini Cooper runs up to 230 too. My hubbies 2017 230i BMW runs hotter at 234. Its all about economy now and I really dont like it either. I tried Redline Water Wetter and it made no difference. My last option is to fit a separate electrical fan on my Cooper and push air through the radiator from the front side and I'll have it set to a switch inside my car and I'll turn them on when I want to like in town or idling. Problem is, every fan is about 2.5 inches thick and I only have room for a 1 3/4 inch. Which means I can only use the room at the top or bottom of the radiator because of a crash bar in the middle. I can fit three 5" motorcycle fans in a row horizontally which I think will still help a lot. Big job getting my fan shroud off though arrrgggg.
@BasinMotorsportsАй бұрын
I had to eventually replace the radiator due to the plastic tanks starting to weep coolant. I replaced it with a larger aluminum radiator and added water wetter also. It stays around the 200-205 range more, but if it sits long enough it will still creep to 225-230 for the fans to turn on. It does take a while to get used to it running hotter than expected.
@paulcomer2266Ай бұрын
It works ! Thanks and my ac cobra 🐍 rides!
@Larbr000Ай бұрын
Wear bars are at 2/32nds and tires lose water displacement at 4/32nds. I would go with the quarter unless I live in Arizona
@Incorruptus1Ай бұрын
It's like showing a Chrysler factory, while talking about Ferrari,...as example... 🤣
@glotrimАй бұрын
Incredible video skills
@idmoosemanАй бұрын
Canaan does do good work.
@koohlogАй бұрын
Hello question do tiida 2006 have transmission fluid? And do you know where can it find it? Thank you.
@BasinMotorsportsАй бұрын
Yes, it should have fluid whether CVT, automatic, or manual. If you can't find it from a local dealer, I know Amazon carries it. I'm not sure how to find it outside of the USA.
@koohlogАй бұрын
Thank you
@josephpiantedosi8210Ай бұрын
Hi I just installed the RPF C5 hud cover everything came out great except the right side towards the steering wheel (where the crack is) lift any idea how I can fix this I followed the instructions to a tee and even used the paper towel roll. If I push it down it will,move down but not stay any help would be appreciated
@BasinMotorsportsАй бұрын
Can you add more adhesive and try to push it down further while it bonds together?
@josephpiantedosi8210Ай бұрын
@@BasinMotorsports should use the same adhesive and should I apply it to the dash since it lifted the original hud bezel
@BasinMotorsportsАй бұрын
@josephpiantedosi8210 You can try it.
@josephpiantedosi8210Ай бұрын
@@BasinMotorsports I will try tomorrow thanks
@ShanIAmBalanceАй бұрын
I think I’ll try this Lefty
@mrvang8077Ай бұрын
What about rain? Wouldn't that get inside the engine bay when it's raining hard?
@BasinMotorsportsАй бұрын
Yes, it would. Or washing it. Some have made covers for washing the car with hood vents installed. I never drove this car in the rain and was cautious when washing it.
@lazmotron2 ай бұрын
Great Video
@lazmotron2 ай бұрын
Great Versa hatchback go to videos!
@kevinb62532 ай бұрын
Thanks budd
@ShanIAmBalance2 ай бұрын
Your instructions are SO good! Thank you and I will let you know how this goes once I get the bulb.
@pyroAdapt2 ай бұрын
Shit... I'm out of luck. I have a penny but not with Abraham Lincoln....
@BasinMotorsports2 ай бұрын
Check the parking lots. I always find them.
@pyroAdapt2 ай бұрын
@@BasinMotorsports haha. Nah I was just making a joke. Cause all oennus have Abraham Lincoln on them.
@NCCarpetBinding2 ай бұрын
What a great thorough review. Very well thought out.
@aallen11732 ай бұрын
Looks great! How many hours did it take you?
@BasinMotorsports2 ай бұрын
About 2 hours total. Figure about 1.5 hours to change the foam and upholstery and 30 minutes to pull the seat and later put it back in the Suburban.
@genericthiccgirl2282 ай бұрын
I really quite like this idea. Did you end up going anywhere with it?
@BasinMotorsports2 ай бұрын
I haven't gotten any farther than the idea and mockup. I wanted to find a separate bumper to cut up, but haven't found one cheap enough that I felt good about taking a saw to. I found another KZfaq channel (Tofu Auto Works) that did similar lighting on a Miata and I found a good controller in the US that can make the lights work as needed to meet DOT guidelines. It's still on my "want to do" list for the future.
@genericthiccgirl2282 ай бұрын
@BasinMotorsports That's awesome! Always wanted to do it to my 2004 Mustang so very interested to see how it goes for you. Will look up Tofu Auto Works. If I may, what controller did you use to make it DOT legal?
@BasinMotorsports2 ай бұрын
@genericthiccgirl228 CorsoMotion has a controller that can be configured like I wanted for sequential lights, brake lights, etc.
@genericthiccgirl2282 ай бұрын
@BasinMotorsports Awesome! Thank you so much. Will subscribe and keep and eye out for updates.
@jimmylanders26933 ай бұрын
good luck driving in the rain with the air filter right below the louvre
@miker.54953 ай бұрын
Is this product silicate free?
@BasinMotorsports3 ай бұрын
The website doesn't specify either way (yes or no). It just says it works with silicate and non-silicate types.
@miker.54953 ай бұрын
@@BasinMotorsports I saw the same.
@astraoptix3 ай бұрын
Weird request, and i pray you read this. I am trying to take on the same project with some other leathery(ish) material i have, but without seam-ripping my current boot. Would you be able to accurately describe the sewing template/patch sizes of the blackandblue boot so i can cut them out? Above and beyond would be sending a photo of them layed out like you had with rulers on X and Y axis so i can copy your process. Any help is appreciated! Product looks great, reminds me of my old gti
@BasinMotorsports3 ай бұрын
I can't respond on here with a picture, but if you message me on any of the other platforms I can get a picture later when I'm in the shop.
@Lauradahl-creations3 ай бұрын
I have a1976 cj7 jeep with gm 4.3 v6 engine and th700r4 Automatic Transmission with overdrive and the highly sought after tough Dana 300 transfer case, with lots of upgrades and new parts. . I want mid to high blue book and either want to sell, or trade, or auction it off but, if I read it correctly, Washington State doesn't allow private owners to raffle off their vehicles. 😡😣
@BasinMotorsports3 ай бұрын
It looks like you need to buy a license, keep paperwork after the raffle, and potentially pay taxes (both state and federal). I'd look at Bring A Trailer, Cars and Bids, eBay Motors, and other sites to see if any of those would be better for you. A local enthusiast to me down here in Oregon listed on Being A Trailer a couple months ago and did well. He had a Landcruiser with a GM swap (kind of similar to your CJ).
@user-kv5df7wy3l3 ай бұрын
The dog is the star here😊
@NCCarpetBinding3 ай бұрын
well done
@dustye7533 ай бұрын
Would you say this glue is like tire patch adhesive?
@BasinMotorsports3 ай бұрын
Patch adhesive is more jelly-like than this when I used it last. This stuff is like super glue. It's very liquid.
@dustye753Ай бұрын
@BasinMotorsports Thanks I ended up using 401 glue, it's on ebay for like $2/ bottle. Smells like superglue, and seems to be working perfectly. I would have thought something more flexible would be better as it's on the sidewall.
@idmooseman3 ай бұрын
Looks good. I wondered if maybe the "top" section was going to fall a bit short of the shifter ball since the console was not fully seated/installed during the test fit. My hands are somewhat large so having the shifter boot top lower than the shifter ball would work fine for me. I may try to do this with my Mustang's shifter boot.
@BasinMotorsports3 ай бұрын
It was shorter than I expected, but fit OK when I tested it. I have since made another one out of black vinyl and Tartan piping at the seams. The new one is taller and sits just below the nut on the shaft.