Can you help? I bought this exact part for my Kenmore 500 . After trouble shooting all the other parts this was the last one left that had to be the problem. I had a struggle putting the flat part of the dial on and properly lining it up with the white part that sticks out to secere that timer in place. When I put the knobs on that seemed wonky too but it went on. Then when I set everything up and plugged my machine and turned the knobs and prayed alot 🙏 this was it. Once I pulled to knobs to start it came off and it did not pull out or start the machine . Can u help plzzzzz
@DzHarryNuttz24 күн бұрын
Your old ones are a lot cleaner than the ones i took out of mine
@duanesharpjr951224 күн бұрын
I didn't see you plug the wires back in
@user-zn1em9lg4fАй бұрын
😂 I had that dream last night. Then I went back to prying and beating on it this morn. Won't buy another Whirlpool or Maytag.
@queennashoba7Ай бұрын
My agitator isnt washing the clothes but it goes through the cycles?
@DG-hb8rhАй бұрын
Bravos works ,but the spin cycle is very weak spin leaving clothes still wet . Replaced shift actuator, belt,pully, tub spline washer and splutclutch ? Any ideas suggestions/help
@togilberАй бұрын
Nicely Done 👍🏼
@IMTheOnE1984Ай бұрын
Any ideas for no water coming out?
@K1TTENM1TTENАй бұрын
So what is the trick to get that bottom shelf out, I absolutely cannot seem to figure out how to remove that bottom shelf for the life of me 😭
@donverga247Ай бұрын
Did you have a full video like what nexts to those screws
@qillerdaemon93312 ай бұрын
Just reach in and pull the wash plate off. Sure... I got the center bolt off, but the plate simply would not budge. Took a Dremel with a cutting bit and cut most of the plate off. Took a chisel and got all but the metal center piece that was seized onto the gear shaft. Soaked that in WD40, then took a 3-prong gear puller and lots of cussing to remove the center piece. This all took three days of YT vids and enough salty language to make a whole Navy proud. This will be the only time I'll ever attempt such a piece of work, next washer will just time its way to the driveway curb.
@nancy4don3 ай бұрын
One additional important step: vacuum off the coils and everything else under there before you finish the reassembly! Only takes a minute, and since you’re already there… 5:08
@alicia-fo3fx3 ай бұрын
Need less music and more explanation please!!!!!and thank you !
@char222224 ай бұрын
I thought this video was just to mess with us and have us waste time but it’s real, it works. I will now continue to dry my laundry and ask for forgiveness for judging this kind human.
@DEdwards2474 ай бұрын
In 5 yrs my agitator broke off now, it doesn’t spin! Trash
@lizbel54234 ай бұрын
My Maytag centennial spins really fast on spin cycle, it is so fast that I never go near it because I’m afraid it might jump at me. Anyone else have this problem? And if so, how did you fix it?
@TreySoSuave3 ай бұрын
Sounds bout right to me.
@fatmirefeta51875 ай бұрын
Please help im doing the same steps and it wont turn green lights only a yellow and a red light is
@lindagarris78615 ай бұрын
I have maytag centennial for 11 yrs np except had to recalibrate 2x This time it looks like shift actuator. If i were strong id pull it out and undo back and but the $20 part😊
@lindagarris78615 ай бұрын
So I tried recalibrating and nope not this time Then did diagnostic Only wash light lit- washer stopped during spin cycle. So it's a spin thingamabob I need
@Bussabignut5 ай бұрын
Okay great, so now what?
@cristishankland36415 ай бұрын
Mine click orange😩
@mariegrabo5 ай бұрын
I can’t get it out anymore I think it’s frozen. How do I defrost it?
@daisyductmechanical66855 ай бұрын
Most likely is stuck frozen. If you have a steamer you can defrost it that way or unplugging the refrigerator for a day also works.
@honor4thoseb4714 ай бұрын
What can’t you get out?
@whoknows1415 ай бұрын
So mines won’t even go into diagnostics mode
@togis34835 ай бұрын
Que romántico 😂
@mickett6 ай бұрын
And a new bearing on the wiggely shaft
@andycarranza41256 ай бұрын
I have a lid lock light flashing. I replaced the lid lock part but the light still flashes. Anything on that?
@daisyductmechanical66856 ай бұрын
Make sure all connections on that lid lock are tight. A flashing lid lock means that the lid is not closed. Worst case scenario, the control board went bad and it is not registering that lid lock. But, I would try to investigate that lid lock first before jumping to conclusions
@swishaboimartinez51326 ай бұрын
Washer turns on and light is on but dryer won’t turn on
And another question, my grandmother washes sneakers, which program should I press?
@ArtyomEryomin6 ай бұрын
And another question, my grandmother erases the curtain, which program should I press?
@ArtyomEryomin6 ай бұрын
Please tell me, my grandmother washes the jacket, what program should I press the jacket, if there is no program for bulky things?
@ArtyomEryomin6 ай бұрын
I love the LG washing machine! Good, you're testing!
@Z33.gi06 ай бұрын
Mine just went out. Starting having a very loud grinding noise at start up, any ideas ?
@BrunoFerreira-sf6gr6 ай бұрын
🙋♂️..hello BRASIL 🇧🇷..👏👏👍😁..thanks for video..
@daisyductmechanical66856 ай бұрын
Hello 👋
@chericedotal72656 ай бұрын
Okay so I thought my washing machine was broke until I done this and now it won't do nothing except for spin and then says done won't even add water or nothing I need help what do I? Before I done this it filled up with water and everything spun wash clothes all that now it don't do nothing.
@user-gf4th3yd5b6 ай бұрын
bs i broke washplate did everyrhing the designer should be fired bad desighn after 10 yrs it will not budge it sticks from all the crap i know i wish it was tha easy no sir
@locus12225 ай бұрын
Mine was completely rusted together. Had to take a chisel to get the old wash plate off😭 not only is it a horrible design. It also seems like theres no consistency between the problem
@ionman51457 ай бұрын
I first tried with a socket wrench to no avail, then I used the impact driver, which removed the bolt. Bolt head is 11 mm or 7/16 inch. Using specialized pry tools I was still not able to remove the agitator plate. 😮
@nickieyoung7797 ай бұрын
Not filling with water?😮
@cruzdimas60187 ай бұрын
You need to take this off does not help for nothing
@josereyes34727 ай бұрын
I did the 3 counter clock wise and un plug for 2+ minutes then the 12-11-1-etc start and light came on...did its thing and no lights stayed on. Washed a load in deep water fill in hot water...will sense spin 3 or times with hot water than it stops the hot water and won't fill up...
@user-ks6qi1hb7y7 ай бұрын
How did you get that nut off, mine won’t budge…….!!!!
@user-ks6qi1hb7y7 ай бұрын
How did you get that nuts off, mine won’t bug
@JMoney-ne3to7 ай бұрын
A-hole
@user-rx5cw7ps6l7 ай бұрын
Whats next please😊
@valerieHenderson328 ай бұрын
Now what lol Lights blinking 😅 How can they stop blinking now