hello... did you unplug the negative cable on the battery before the work.? I will be doing the same , i just want to know if i have to unplug the negative cable from the battery. Thanks.
@StevenFine-m6tАй бұрын
Which anaerobic sealer did you use on the capscrew threads?
@josehache51456 ай бұрын
Hello guys. Any ideas of why mine is not working? I did the same steps but nothing still. Thanks in advance
@garrettjohnson13826 ай бұрын
You don’t need that washer and you’re supposed to pull the boot off the it’s easier to push in the pin then push the boot back over
@skilltouchinc Жыл бұрын
What kind of paint do you have on your humvee?
@beurownboss1554 Жыл бұрын
excellent video, this was super helpful and just what I needed to run a manual oil pressure gauge for testing. Thanks!
@M1151A1Ай бұрын
Do you run the manual gauge to where the sender threads into?
@beurownboss1554Ай бұрын
@@M1151A1 yes that’s exactly where it goes, you’ll see it threads in at the back of the block easily accessible from the doghouse. Most manual gauges come with an assortment of threaded adaptors so you can match.
@M1151A1Ай бұрын
@@beurownboss1554 thanks for the response!
@wakesurfingfool Жыл бұрын
So...after all that, did the horn actually work?
@ivanar95722 жыл бұрын
Muchas gracias por vuestros consejos. Son de gran utilidad para mi. Acabo de comprar un M1026 y soy de Barcelona (Spain), y estoy muy perdido con esta mecánica.
@gregorycox32 жыл бұрын
Why did you have to change it? Just curious
@dylanwarthan50542 жыл бұрын
Where is second thermostat?
@fxelisa22352 жыл бұрын
Have you a number part for the horn clip ?
@maciejwojciechowski89142 жыл бұрын
What is the # on the termostat and can I get it at NAPA ?
thanks for the video. how do you know if it is the gauge or the sending unit?
@farmsgrace3413 жыл бұрын
Is the operating temp of the new thermostat the same or cooler than the original?
@Subgunman3 жыл бұрын
A bit of wire brushing the column splines with a bit of anti seize goes a long way in case one needs to remove that wheel another day....... Great info!
@BMD110003 жыл бұрын
Not to the poster, but to anyone watching, if you need the mechanism that was used to remove the wheel, that's called a gear puller or steering wheel puller, not pulley. Also, spraying the splines with PB Blaster will help a lot.
@jferrer19733 жыл бұрын
very helpful walk-through. saved me a ton of time on my fix. thanks.
@andrewcordova62883 жыл бұрын
Thank you for posting this
@benheinrich3 жыл бұрын
thank you for taking the time to make and share this
Did you find it easiest to thread in the new sensor from above or did you need to go from underneath?
@anibalquinones4 жыл бұрын
Puller... Not pulley
@Whatsthatsmell-rr8qb4 жыл бұрын
What’s the nsn?
@AlphaLimaATC4 жыл бұрын
Great video. Beep the horn next time!!
@tangledline4 жыл бұрын
Can you guys answer the questions below?
@ericherr6114 жыл бұрын
If all else fails install an aftermarket horn and horn button.
@theautodidacticman_4 жыл бұрын
Aren’t these directional? Which way should they face?
@oresteskindelan46554 жыл бұрын
Amazing guys.Nice job.
@johndoe-wk1ru5 жыл бұрын
Great video! Wouldn't advise standing over anything with a split rim while airing up.
@drofdata5 жыл бұрын
What happened to the install of the new alternator video?
@Card_19975 жыл бұрын
So my horn is inop and no one in the shop knows why. We have both grounds on and everything wired correctly but it’s not sounding. Any guesses? A horn from another truck did not work on my truck and my new horn did not work on another truck. So I think I have two faults or there is certain horns for certain types of trucks.
@nathanpurney5 жыл бұрын
Clean and simple video. Well done. This is something I may need to do after trouble shooting the sequence of possible issues. Relieved it is very simple to do. What were the symptoms that lead you to change this OPSU? I am currently looking at an inconsistent start up and running pressure of 65-75 on my 6.5. As we know normal run window is 40-60.
@mygooglusername5 жыл бұрын
Great Video
@nathansteiger24095 жыл бұрын
LOL, YOU GUYS ARE A JOKE! Don't call yourselves "hmmwv guys" if you can even change a light, lol!
@nomad-pq4yw8iy7v5 жыл бұрын
1st video i've seen with actual plug and play lights
@js41205 жыл бұрын
FYI regular superglue is fine on o rings its used to make custom sized o-rings made from rubber
@VileMisanthropy5 жыл бұрын
There’s no installation tool or Dowel for that extra hole to line up the two half’s?
@m998hmmwv76 жыл бұрын
Subscribed.. Thank you for posting !
@baum5256 жыл бұрын
So where did you find your thermostat and what's the part number I have a friend looking for one
@user-gg9tv3uv1w6 жыл бұрын
재미난 취미를 갖고 계시군요.🤗
@m998hmmwv76 жыл бұрын
Numbers should also be on the rear of the bucket and the wires coming out from the back.
@m998hmmwv76 жыл бұрын
You didnt beep the horn damn it.. 😣 lol
@OffGridretreat6 жыл бұрын
Can you add the link to find the same ones that you installed
@moxhouseconstruction50926 жыл бұрын
This might be a stupid question, but how do you know how many ounces of beads to put in the tire to balance it? Great video by the way. I just got new tires for my M998 and will be taking the wheels apart in the the near future.
@OffGridretreat6 жыл бұрын
What type of light is that and where did you purchase them from