the gbc14-200 we just dyno about 16psi on an 720cc 3 cylinder engine and can only make 105kwz atw (E85) 18psi it made 106kwz and falling over just wanna know is that what the gbc14-200 iz cable of? what 200hp rated at wheelz or at the crank?
@ivangonella13 күн бұрын
This is more about "how we void your warranty".
@TurboOST-UFAАй бұрын
Эффект Мортона
@321rorАй бұрын
What's the difference to twin scroll? Looks like the same divided housing, just a different name
@luvhcchris2 ай бұрын
Love my g30 :)
@Ellacost8312 ай бұрын
Hello i have a question, after installing new Garrett turbos on my 2017 Raptor i no longer get a bov sound when reving on idle, i do get bov when the truck is running but not when reving in neutral or in park
@ryanwing87652 ай бұрын
Muffled mask, hard accent and loud background noise. Can't hear a **** thing
@BrodeyDoverosx2 ай бұрын
Tell me about the compressor wheel design. “We’ve improved the wheel design” Dutrrrrrrrrrrrrrrr
@PHLTHS3 ай бұрын
I have emailed Garrett in the past for their detailed Turbo Efficiency Map and Turbo Speed information without any luck. Is there a reason why Garrett would release this information to tuners so that we can input it into our ECM's to extract the optimal from these turbos?
@user-zi8bd2kh1n3 ай бұрын
Garrett is in difficulties now
@67636034 ай бұрын
can hear a thing with the high backround music
@mattmorrison69584 ай бұрын
A great video, and embedded in there a fantastic explanation of why a divided turbo setup can generate better VE/response!
@dynodom46774 ай бұрын
Why the Mask?
@ramoncitoflores69315 ай бұрын
👏🏼👏🏼👏🏼💪🏼👍🏼👍🏼❤️
@nomessgarage71817 ай бұрын
I want to GT 45 psr Turbo Bullet mode I need
@jarradjeter15237 ай бұрын
*Promo SM* 💋
@DontAttme7 ай бұрын
Is this too much for a cbr650r?
@UNLKYHNTR7 ай бұрын
The fact that a mass is rotating at that speed without blowing up...mind boggling.
@GabrielRN287 ай бұрын
On 0:26 i thought the one at the center was the intercooler. But I noticed it’s the one illustrated above, so whats that at the center? Thanks for answering
@speedycrax2 ай бұрын
i believe that's the separate air filter for the turbo. there may be high flow versions of this intake too for max performance. After all, since this air goes back to the engine, u might wanna keep it as clean as possible
@SOCALPRINTER7 ай бұрын
I'm building a Mercedes OM606 TD for Off-road Use. And considering the GBC22-350 for my 3.0L Diesel motor. Will Garrett be producing a GBC23-400? or similar frame to 400HP?
@chewdoobautomotivedetailtm28838 ай бұрын
😎😍
@FFCRBDI8 ай бұрын
Look at this guy wearing his nappy. Just shows intellectuals can still lack common sense
@ramoncitoflores69318 ай бұрын
❤ wonderful 👍👍
@quilonturbo24678 ай бұрын
Quilonturbo turboservice
@maoinc138 ай бұрын
Can you imagine that this kia end up stored in a garage ? 😢😢😢😢😢 What a waste !! 😢😢😢😢😢
@Estebanmorenozapata8 ай бұрын
esta teoria si me gusta
@f150lightningboy9 ай бұрын
It would be great if you had a Turbo in your hand and pointed out all the possible leak scenarios on the Turbo instead of a PowerPoint.
@dsfs179879 ай бұрын
so 15% of payed for h2 goes straight into tail pipe to make the system run and no word how the h2 is made in the first place, that is omitting facts to fake the co2 neutrality and push a technology which requires expensive infrastructure to maintain (fueling stations)
@jeongpilkim49689 ай бұрын
garrett turbo 2674a805 찾슴니다
@jivantakirstenpillay61289 ай бұрын
When upgrading stock Turbo downpipes, how do we calculate what is the optimum size for best flow while still keeping the the Velocity high ? I have upgraded my Dp from a 42mm to a 63mm, and even after a Tune the car feels laggy at low rpms. It only comes alive above 3k Rpm. If you calculate the area of the Upgraded DP, it works out to 2.25x the size of the Stock DP. On stock cars with small turbos, what would be the best upgrade in Size for both Performance and maintaining the Daily driver characteristics ?
@MsOMGwtfnoOb9 ай бұрын
Is the g25 550 good for a 2jz gte vvti ?
@haroldhaynesiii10 ай бұрын
THat boost advisor doesnt give me ANY results... Pretty useless
@alj226410 ай бұрын
OK I know what I'm gonna do 😮OOOH 😮OOOH
@khizar198110 ай бұрын
Oil leak in intakes
@NageswaraReddy10 ай бұрын
#Garrette got my certification thank you
@minni109410 ай бұрын
Does Garrett sell tube and fin intercoolers?
@spsciroccomk211 ай бұрын
I have checked all of this list, everything is installed proper and talked to 4 experienced mechanics and no one can figure out why my New gt3076r ran for 5 min at idle and poured out lots of oil on both the compressor and turbine side of the turbo.
@ls87gbody19 күн бұрын
Crankcase not vented enough to allow proper turbo draining into engine?
@spsciroccomk218 күн бұрын
@@ls87gbody I had a -10 AN from the crank case and another -10AN from the valve cover going to a oil catch can with vent ports.
@ls87gbody18 күн бұрын
@@spsciroccomk2 you ever figure out the problem?
@spsciroccomk218 күн бұрын
@@ls87gbody yes it ended up being a fitting that was not fully sealing on the inside of the turbo housing, causing aeration in the oil and allowing it to blow by the seals. I had sent Turbo out to be tested and it came back with flying colors. It was perfect. I changed the fitting and I also added an oil pressure regulator for good measure.
@zannetoschristou533911 ай бұрын
ROB SIMMONS what is the suitable oil restrictor (mm size ??)turbo 3582R ball-bearing turbo garrett ??
@catalina27able Жыл бұрын
got a new turbo but is not creating any boost !
@joshmazzoli4664 Жыл бұрын
I'm like the reducer for low rpms that opens up larger into high rpms with a half cut away butterfly, exhaust dump valve inline b4 the turbo after the manifold or in between would spool fast and as the rpms load the exhaust up increasing it would open back to normal like open in high rpms but closed as soon as you hit the gas...would be great if was tachometer signal controlled😮😢😅
@quilonturbo2467 Жыл бұрын
Quilon turbo turboservce🌹
@Stoparts Жыл бұрын
Cool presentation colleagues 👏
@Stoparts Жыл бұрын
Bravo 👏
@Stoparts Жыл бұрын
Bravo 👏
@ronrobbins5555 Жыл бұрын
Holy Crap is that you Rob!!!! Its your Canadian Homeboy Ron, Liz's son from amazing video machine. How are you brother?
@SGRyuma Жыл бұрын
i felt the apprehension in your voice before u started the car lmao this how i know you really build cars XD