Just bought a fuel pressure regulator to go in before I tune the carbs. Should I set this to what you recommended? I have a fiat 1600 twin cam engine in my sylva fury
@Project380Күн бұрын
thank you for a nice detailed video
@jockofthebushveld2992 күн бұрын
Quick question I see a lot of Picture's of Webber Carburetors where the Trumpets have no Filters fitted as is the case on this One,doesn't this allow dirt and dust enter the Carburetors?and cause blockages to the Jets.
@JamesTomlin-ll7lt3 күн бұрын
yooo! this guy is using a door camera for this video 😅😅🤣
@perjian16973 күн бұрын
Cheers!! Good vid!
@rotorblade95086 күн бұрын
I would wet the wrap whenever working with them or in an area where there is a risk you could touch them otherwise there is a risk of tiny needles thrown into the air. if they are wet the dust is less likely to get airborne.
@mynameiswoody45297 күн бұрын
I have Ford Focus 2007 model running on petrol and check engine lights have been a problem for a while now and it says EGR system flow fault, it might take more time and cost to order a new EGR and replace so I am planning on deleting or blocking the EGR but still unsure about it. do you recommend of using blocker plate for the solution?
@chrishull99838 күн бұрын
Thankyou - a well presented and easy to follow procedure - the only one to be honest I have found, and I have been looking for ages. I am actually running Dellorto 45's but I believe the process is common to both. .
@ruunlimitedstudios462910 күн бұрын
Mfn right this is a really good video bro thank you
@FastRust10 күн бұрын
Cheers bro thankyou 👍🏻
@keebitsimplehu395411 күн бұрын
Or just get the right tool for 10 bucks 😂
@robpenfold950013 күн бұрын
So, no need for a remap after new/bigger injectors?
@franksomarriba671913 күн бұрын
Great video, thank you. Can you explain why we have to pump air in the cylinder? An answer would be much appreciated.
@katananomi13 күн бұрын
Thanks
@JamesZ102513 күн бұрын
Just get a cable gun
@fargogemini69414 күн бұрын
Electronic gas regulator
@williambailey991715 күн бұрын
heck of a deal bud, ive wasted many ties not knowing this, thanks
@alexanderlapierre404017 күн бұрын
Why is there no grey red wire under my dash. Only one at that location is solid grey/then to solid red halfway through. Is that the wire you are talking about?
@buster540718 күн бұрын
Great video I am thinking of using the same setup can you give me the dimensions of the 180 pipe that you have used thanks
@buster540718 күн бұрын
Just saw the link about this now😂
@adventure_rider_uk19 күн бұрын
Thank you for that 🙂
@MartinJames-dw9xt20 күн бұрын
Happy days,, just been pulling my fecking Hair out with this problem!,🙏
@octymocty13221 күн бұрын
the st\st ties wer origanly for fire pannle instilations and tidying the cables up
@bilgehandavarc939422 күн бұрын
how did you close carburatore
@fiouable22 күн бұрын
Bless you
@dominicmorris81927 күн бұрын
Did this dyno ever happen?
@sawleyram7405Ай бұрын
I know this was explained on a Capri, but this is a really useful video -- good context to the procedure and why it's done, plus clear instructions.
@madskylinegt4339Ай бұрын
I am doing the exact same set up you are you willing to share that MAP? I have the exact same things you are running and cant find a remote tunner😭
@valtercristino1999Ай бұрын
Great video! I have a pushrod engine, should I tune the valves after doing this?
@charliegrech5598Ай бұрын
Such a good video. Clear, methodical and so simple to follow. Thank you. 😊
@nathanx1275Ай бұрын
Funny how I came here looking for info on a diy supercharger build but I’m fitting mine to a Capri only to find out you also have a Capri lol
@stevemcilroy9518Ай бұрын
That first joke was shocking
@tankeaterАй бұрын
I have Black DEI Heat Wrap with black stainless steel worm hose clamps... Looks better, more coverage, easier to fully tighten, easier to remove. 👍
@Toptechitsimracing9601Ай бұрын
love the dual throttle body setup , i would love to do a supercharged mx5 build but very expensive where I am from , may need to settle with a ITB Build
@mhh3Ай бұрын
is this channel dead?
@Cossi2000Ай бұрын
Thanks for sharing this video. The method works great 😜 Greeting's from Germany
@julianhunter9455Ай бұрын
Lovely little mx5!
@dylancade2003Ай бұрын
I’ve allways used stainless hose clamps
@stealthslayer4406Ай бұрын
Very helpful information, cheers all the way from Perth Australia
@claytoneccleston7382Ай бұрын
2 litre pinto is a non interference engine
@MDM1992Ай бұрын
You made yourself sound like a right current with that resistence joke.. sorry couldn't help myself 😂
@FastRustАй бұрын
Behave!! 🤣
@patrikpodholiczky7312Ай бұрын
Hello. In this type of car, is the ignition with a switch or a signal?
@impactodelsurenterprise2440Ай бұрын
Can't you just rotate the crankshaft so the piston sits TDC?
@juggnautbitchАй бұрын
You know how you get those steel zip ties tighter? You buy the actual tool meant to tighten them, a cable tie gun.
@speedfreak8200Ай бұрын
Needle 🪡 Nose Pliers on my side of the pond 😅 thx bud
@seanhiggins704Ай бұрын
I wish I could give this video 2 thumbs up
@DarrenVisagie-hz6tsАй бұрын
Hi where is the number one plug lead in the dizzy cap
@jamesford8271Ай бұрын
Just bought a supercharged mx-5 and couldnt agree more with your point of view. Will certainly be looking to do this
@WastedElephantАй бұрын
Is it always necessary to remove the rear half shaft, or is this just on Capris?
@RacecarsAndRicefishАй бұрын
Hey I'm desperate to know what throttle cable you got to run between the two. I'd like to avoid buying a bunch that don't fit like I did for my supercharger belt
@misunderstoodvtec8299Ай бұрын
Hi mate what size pulley do I need for a m45 slk 230 supercharger please just struggling to find watched your video any help will be appreciated