Can you cut 5 mm PVC board?

is it safe to eat ?

tengo un problema con el laser se ven dos puntos y en lugar de punto principal una linea (- -) con un macro espacio entre ellas, saben si tiene reparacion?

What model is this?

Tenho mandril estou com dificuldades em fazer círculos

Not even going to lie, this thing is such a nightmare, I can't wait to see it gone. My wife bought it thinking it would be useful, it's a joke to setup and calibrate and such. Don't understand why companies make things such a freaking pain in the @$$

Nice

NO WAY my LM 2 PRO with the LU2-4-SF laser module does that!!😥

Super

why would you change your firmware site? makes zero sense.

Whats the tumblr coated in?

What do you put in the swab to clean it with

I just purchased the new. 20W laser head did your kit come with the extra offset to move the screw holes on the side to move it forward for the larger head I cannot see it in the picture in the description on their website.

1:09 I finished assembling mine, when I turned on the power the laser stays on

You forgot to show the setup

What is the output power of the laser?

What kind of wood & glue do you use and where can we purchase?

Is that an adapter

I notice the Air Assist block comes with a threaded hole in the side. Mine came open so the air get to the noozle but also scapes from the side. Is this hole suposed to be close? Thanks

Which model is this?

which height should i set the LU2-2 module to?, i want to cut a 2mm thick plywood

Hello, installed my 10W upgraded module on my LMP2 and when powered on, the laser instantly turns on and begins burning with no USB cable or computer connected. Any ideas?

Is this a 10 or 20W laser?

Slow it down for the love of god

Holy crap how can anyone follow this

Which model motor is this?

De un, ils auraient pu garder le même (slider) De 2, cette carte mère aurait pu à mon avis être intégrè à la carte mère initiale. Ça faisait deux de piques cette carte ouverte à la poussiëre et cela m’a fait pensé que l’on servait à un essai. De 3, le système d’aération du refroidissement collait la poussière au bois et la buse pour l’assistance aèrienne était trop ouverte et en plastique donc les filets ne tenaient pas longtemps du fait qu’il fallait ouvrir souvent pour nettoyer. Elle m’a coûté chère pour une mauvaise expèrience. J’ai par la suite laissé tomber Ortur.

Buenaso

can ortur laser master 2 LU2-10A cut paper?

How to install Z-axis lifting device on olm2ps2 with LU2-10A?

Mine isn't a wire issue. it is a male / female connector issue

My favourite 10w laser 👍

برنامج العمل هل يمكنني الترجمه الى اللغه العربيه

Where to purchase

I have the LM3 (10W) and can not engrave on stainless steel. Can you help?

What kind of toaster do you use?

Where can I buy a new key switch for ortur laser master 3, or can i sold the wires to aboid the switch, mine is broken.....

Nice! And what did you use for color? Is it permanent?

Hey! Nice tutorial! Maybe think to export the settings on your computer so you don't have to look for the parameters when you want to switch from Y-axis to YRR... instead you'll just have to load the backup for each modes!

When you buy this item you will lost to much money and time

Tecnical service or seller dont help any problem

Item is not work properly

Dont buy this item you will lost your money

Main bord problem item always stop and nver can use

Laser modul problem

It is not work properly

Item very poor quality

Always main bird problem

No body help about problem item is not real 10w