Fixed it for me! Mechanic wanted $1077 for a new clutch actuator A 😢
@jayfixesthingsКүн бұрын
Is the tcm vin specific?
@arthurfricchione8119Күн бұрын
New subscriber and I own a 99EXL accord with only 62k miles on it. I just changed the cabin air filters and yes they are in correctly but I noticed the middle A/C air outlets have very little air flow. The driver and passenger out let’s are fine. The A/C also does not feel as cool need to check it with a temp gauge. The scanner says all switches open and close properly. I’m definitely going to check the system your way. Great video and thanks for sharing. 👍. Artie. Any inputs greatly appreciated
@markhuyette8509Күн бұрын
What was All that noise when you were running it after it was fixed sounded like a swarm of bees 😂
@FixItPhillipКүн бұрын
It's the mic on the camera, makes it sounds loud when it's not lol
@jamesbondaygee4 күн бұрын
What does it mean if it's not clicking I don't think mine is.
@Mistamerv5 күн бұрын
I have a crank and no start issue after new pump was installed
@joshuajudy16796 күн бұрын
Great video. You do a good job at explaining things. Thank you.
@thomasschaefer95078 күн бұрын
Best video I have found 🎉thank e
@scott618718 күн бұрын
ahhh. just read some comments below and realized that I also have the 4x4 version and will have to remove the front differential. Damn!
@scott618718 күн бұрын
that sir was one of the best explanations I have seen for the removal of this pan. other guys are taking the entire drive shaft apart. And like bucket man below, I was attempting to do it in my driveway. I just found out that a friend of mine has a full garage with a lift in his house. I'll be there this weekend with my pan gasket and o ring. Thanks for the excellent tutorial.
@ross341210 күн бұрын
Just got a quote for $1100 parts and labor(Inc flush/fluid) on a 2004. Is that high or fair? Thanks, great vid!
@FixItPhillip9 күн бұрын
That sounds high
@MM-ji5je12 күн бұрын
Insanely good video.
@FixItPhillip12 күн бұрын
Thank you
@DavidBChacon12 күн бұрын
Pops and I were on our lunch break at Chipotle stuck in the parking lot waiting for AAA and saw this gem video and banged on the tank and started right up after an hour of trying thanks brotha!
@khyberafridijamrud12 күн бұрын
Damn bro . I was looking for this video unfortunately I didn't find you . And the mechanic trapped me and said abs problem. After they fixed I noticed a ground wire from body to abs . 😅 I lost 1 thousand dollar
@PottersWork12 күн бұрын
Thanks for the video brother, all the other videos I saw had torsion suspension and I couldn't find any info on the coil setup. Just wanted to see what I was getting into before we started on my boys truck.
@gapo62angler9314 күн бұрын
Great video, I wish I could do this myself but with back issues it’s impossible for me. How much does something like this usually cost , parts and labor for a 2020 TRD OR?
@matthewclaxton715215 күн бұрын
I love the rooster in the background!
@peaches984316 күн бұрын
As some one who was never changed a hub you completely skipped over how to remove the brake caliper ontop of that idk what even bolts you used to help remove the rotor
@kurglover16 күн бұрын
How much does the labor cost? I’m having the exact same problem in my sts
@NanceLvr17 күн бұрын
You make of it easy work. Excited to stop my Tacoma vibrations 😆
@JosePerez-eu9ih17 күн бұрын
Very nice, instructions r awesome 👌 👏 thanks brother 🙏!!
@FixItPhillip17 күн бұрын
Thank you
@victorvillasana340918 күн бұрын
I’ve seen some tensioners made of aluminum others steel for these Hondas. Is there a difference?
@petratical20 күн бұрын
Very good video, and instructions. But after taking out that hose, I noticed it was in decent shape and no leaks. Could it be another hose in that area that would cause it to be dripping coolant down from the EFI?
@TheTomar3321 күн бұрын
There no other way to test relays?
@williamtreat589321 күн бұрын
did you do this job because you had a misfire on one cylinder or more than 1 cyl? i only have a misfire on cylinder # 5 i have replaced the fuel the plug and the coil. now I'm going to do a valve job on # 5 and I will check 4 and 6 while I'm in there.
@BrettSwanson-xb1zd21 күн бұрын
Hi Phillip, I just replaced the master and slave cylinder on my 01 7.3 Powerstroke. Now after not having any issues with the previous master/Slave cylinder my clutch pedal is getting stuck and feels like it has air in the system. Is there a way to bleed the air out of the system? I bought a prefilled South Bend clutch kit.
@yumajosh371022 күн бұрын
Damn I watched this thinking it was going to be easy. I then read the comments and apparently since I have the 4x4 model it’s a lot harder. Really didn’t want to have to bring it in to the shop if I didn’t have to
@sarahguin74007 күн бұрын
Just unbolt the motor mounts and jack up the oil pan with a 2x4 and the then put 2x4s under motor mounts. Remove oil sensor first.
@almoraleta191523 күн бұрын
What are those 2 screws called(connects the motor part to the mechanical part) of the iac valve? The black plastic to the aluminum portion? Thanks.
@FixItPhillip23 күн бұрын
You need a Security bit, it's like a torx but 5 point
@daveb838323 күн бұрын
what scan tool do you use?
@FixItPhillip23 күн бұрын
Autel ms906ts
@Forte.fitography24 күн бұрын
Hey I have it’s same motor. How did you do this without removing the crank pulley and belts. I always thought that if you change the tensioner. You should replace the belt. My situation is that the the water pump and components have been replacedd before except for the hydraulic tensioner. Can I do this without removing the every (minus the timing covers)
@FixItPhillip24 күн бұрын
You have to remove the crank pulley and lower timing cover, I took off the cover and reinstalled the crank pulley to be able to show the issue clearly
@brandonlogan260024 күн бұрын
Do you absolutely need the angled feeler guages?
@FixItPhillip24 күн бұрын
No, I'm sure you could use straight ones too
@brandonlogan260024 күн бұрын
@FixItPhillip thank you! I just hve 2 more questions though, it is possible to do this without having to fix a potential surging idle with a Honda OBD code reader and reset it? Could I just disconnect the battery, leave the TB hooked up clean the TB and get away with no surging idle after I put it all back togther and start the engine?
@FixItPhillip24 күн бұрын
@brandonlogan2600 you can try a battery disconnect for about 10 min to see if it'll clear the code
@onurarslan126926 күн бұрын
Hi everybody Can I take this part number?
@shaneluck257026 күн бұрын
I have to admit it is sad that you have to dismantle half the engine to replace spark plugs and coil. I think I'll leave it to someone who knows what they're doing.
@lejend6926 күн бұрын
I have a p0300 error code but I’ve changed coils plugs fuel injector and my car runs clean but the code comes up every now and again why
@purpstatus27 күн бұрын
Do you have the part number for that tensioner?
@marlonfb6_raiden66227 күн бұрын
Hello i have a 2012 nissan Maxima. Im sure i have A starter issue. But im not sure bc i have orange key light on the dash.A friend told me that the light will apear when it has a bad starter or alternator. Any ideas will help thank yall!
@KenSimmons-n7m27 күн бұрын
Thanks
@cfkoster28 күн бұрын
Thanks 1000 times for this video. Indeed when Phillip can do it than Casper as well. You inspired me to try do it by myself.
@Mel-by4ur28 күн бұрын
How much would you charge someone to change the tension belt?
@joe2thesequel28 күн бұрын
My first move is swapping all the relays if they are all the same
@qt919529 күн бұрын
Had the same problem with my accord. Watched every videos related to high and low idling and still had the same problems. I was lucky to get your video and it made a difference. You saved me two weeks of headaches. Did exactly what you told to do. Thanks for sharing your expertise.
@michaellesa42729 күн бұрын
Good job. Thanks, very helpful 🙏🤙😎
@EngineFunDoeАй бұрын
Thank you!!
@colesoum6913Ай бұрын
I heard the timing belt pulley tensioner bearing is a little dry sound you should just change everything timing belt kit so engine last another 100K miles or more. Next time buy a car with timing chain.
@QsilverFpvАй бұрын
I'm looking at radiators for my 2006 Camry. Do I want a internal transmission cooler in my radiator or without what does it matter
@exemuzikАй бұрын
I thought he saved my life. The truck started running but it was only for a minute. But it was enough for me to pay $239 for a towing. He is right, this is how you diagnose and solve but it might not give you enough time to drive. It was my first signal for the issue. If you have a problem with your fuel pump, just replace it before you drive
@rinserepeat2877Ай бұрын
Hi was wondering what the 'upgraded relay' number was or what you were calling it? Video was blury for that image.
@FixItPhillipАй бұрын
Should be a link in the description for the relay
@rinserepeat287723 күн бұрын
@@FixItPhillip duh, I should have checked. Thanks for the video and good job.
@rinserepeat28779 күн бұрын
Actually, you say " I remember the upgrade to a Mitsub???XXX Mitsubishi ?? and you happen to have one." You only have link for OEM.
@FixItPhillip9 күн бұрын
@rinserepeat2877 mitsuba, I believe the link is for the updated version
@rinserepeat28779 күн бұрын
Never Mind...I found it, 'Mitsuba' found on ebay too! thanks
@user-lm3gb5gd1vАй бұрын
شكرا على الفيديوهات الحلوه والراقيه
@jameslintz9411Ай бұрын
Somic😂❤.
@codymoncrief8478Ай бұрын
This is probably the most user-friendly cylinder design I have seen.