They're not expensive and they have crazy good grip.
@SunshineRoadYearRoundRVParkАй бұрын
I’m looking at one of their cams for some fast burn heads I recently bought. Do you know what part number that cam is? Sounds nasty.
@Someguy13sevenАй бұрын
Most direct info. Cheers 🍻
@code3kcАй бұрын
I just found the transmission temp under "Service Check"
@63bravogarageАй бұрын
That’s where it’s suppose to be. But on the latest version it does not have it.
@code3kcАй бұрын
@@63bravogarage I just picked mine up today, was a little frustrated when it wasn't right with the other live data metrics. Thanks for the video
@clayton383Ай бұрын
What cam is that? Sounds great!
@63bravogarageАй бұрын
Clay smith roller cam .510 .290 duration
@Nativemom2082 ай бұрын
I have a 67! ❤❤❤
@63bravogarage2 ай бұрын
Nice
@Nativemom2082 ай бұрын
On the column or it doesn't count😊
@RomeOpalec2 ай бұрын
Thanks for showing this! I couldn’t find DIY videos out there. You’re a lifesaver! Cheers!
@RodSquad-Reviews2 ай бұрын
@63bravogarage how is the Briggs Spartan holding up?
@Sentient212-Fortnite2 ай бұрын
What size belt is that
@63bravogarage2 ай бұрын
Don’t know the size, but the part number is: 265-805 for a Stens brand. 954-04090 is the OEM part number
@63bravogarage2 ай бұрын
4L250W is the Napa number
@Bill-wz6tw3 ай бұрын
I got the same scanner and I am not experienced with it enough to give a thorough opinion of it yet but I get comms disconnecting and failure to auto identify the VIN I updated the firmware to the latest version before I ever even used the tool from day one I am not sure what is going on with the thing I am going to keep using it until I figure it out I hope I didn't get a defective unit because I didn't buy the extended warranty
@63bravogarage3 ай бұрын
I was able to return mine without paying the restock fee.
@nordland22353 ай бұрын
My tj has 4 wheel disk brakes....does that work for mine ?
@63bravogarage3 ай бұрын
I cannot confirm this.
@Charrell19413 ай бұрын
Best way is don't ever buy a whirlpool anything! Second day we had ours it leak water all over the kitchen floor. Ice maker never worked the way it was supposed to, after 7 months it quit working altogether and had to replace it. I will never own another Whirlpool product again. I also checked what other companies owned by Whirlpool and will never buy those products either.
@wheaterz75673 ай бұрын
Yes, like the first commenter stated, this is the INNOVA 5610! The owners manuals are virtually the.same. The difference I noticed though, the Zurich model shows a 90 day warranty on the back warranty page, where the Innova shows a 1 yr warranty! Wonder why that is??!! But it appears they have different contact #'s, so when you call Zurich are you essentially contacting Innova or a division within Innova? That's what I would like to know. Thanks for posting.
@63bravogarage3 ай бұрын
When I contacted tech support it was a harbor freight rep. They did not know anything unless it involved reading off a sheet.
@treauking88423 ай бұрын
My drum won't rotate. Any advice?
@63bravogarage2 ай бұрын
Try putting your lug nuts back on the studs and using a pry bar placing it between 2 studs and using the lug nuts as pry points to try and turn it to your access point. Another thing you can try if that does work, mount your wheel back on and see if you can get it to turn that way.
@leoneentertainment29503 ай бұрын
pacific ocean?
@robertromero22373 ай бұрын
Should I put teflon tape on the threads?
@63bravogarage3 ай бұрын
I would
@AlexAVify4 ай бұрын
Ran into the same issue. I was trying to read the transmission temp for a 2019 highlander xle, no luck.
@63bravogarage3 ай бұрын
I bought a Xtool ds 7 bi directional scan tool off Amazon for just a little more than what I paid for the ZR15s. A lot more capabilities for a little more money. It was worth it
@wheaterz75673 ай бұрын
@@63bravogarage Does the D7S require a subscription service? I know some XTool scanners give updates for a couple yrs for free, but you have to pay when it runs out. I'm curious to know, thanks!
@63bravogarage3 ай бұрын
@@wheaterz7567 it offers 3 years of free updates and $99 a year after that, which is not too bad I think. But if you choose not to update can still use scanner to my knowledge
@Jim-MT26 күн бұрын
Mine read the trans temp on my 2016 Highlander XLE. Helped me change the fluid.
@Mr2004MCSS4 ай бұрын
Innova is who makes that Harbor Freight scanner. It's equivalent to the Innova 5610 which I own. The firmware in my 5610 is exactly the same as what is showing on your screen. Unfortunately there are a lot of holes in these scanners. I have some higher dollar Launch based and Autel based scanners which show way more information. You might search for some Innova 5610 reviews and see if anyone else has your issue. There are quite a few reviews of the Innova version. Hopefully Innova will fix this issue for you at some point.
@63bravogarage4 ай бұрын
I ended up coming across the Xtool D7S which I purchased for $366 and is comparable to the launch. It’s crazy how I paid $319 for the ZR15s and the Xtool was only $366
@Mr2004MCSS4 ай бұрын
@@63bravogarageYes, I have heard of the different Xtool scanners and contemplated getting one of them but I ended up getting an Otofix D1 which uses Autel software since its made by Autel. Launch and Autel are the two main software versions of the aftermarket scanners out there that are well known. The Otofix D1 Lite is in the price range of the Xtool that you bought and it has most of the capabilities of the larger more expensive Autel scan tools.
@jorgelopez93054 ай бұрын
How did you know your cylinder was bad?
@63bravogarage4 ай бұрын
It was leaking
@makerwright4 ай бұрын
Just dealt with this today when tuning... Thank You. I noticed plugging the hole made idle AFR go from 14.7 to 12.7 (too rich).
@paulcondie25204 ай бұрын
I've had mine for a year now, and i love them! I've heard horror stories but not an issue with mine. Rumor has it the early tire molds were the problem. Can't beat em for the price, remember to rotate rotate rotate!!! Lol
@user-cw4kk3dz4c5 ай бұрын
What size and brand of leveling kit do you have?
@aslmx19185 ай бұрын
Stock springs and rockers?
@63bravogarage5 ай бұрын
Roller rockers and stock springs
@ChristopherSmithey5 ай бұрын
Excellent work!
@montepatton90405 ай бұрын
Great truck. Sounds great. Looks great.
@montepatton90405 ай бұрын
Thanks for sharing. Great information.
@f1david6 ай бұрын
Thanks
@LightningFabrication6 ай бұрын
Just picked up a light kit for mine Cheapest I could find. Shipping and tax came out to $90.48. Got it at Tail Motor Sports Genuine Spartan, 2 models to choose from, Discount figured at check out.
@jsanchez46527 ай бұрын
I thought the same
@notspcl93047 ай бұрын
Have u seen where to get replacements for the 2 small rectangular pieces for the door stop?
@63bravogarage7 ай бұрын
I think you have to buy it all as one assembly
@lacolello66447 ай бұрын
Can we see it on the road please. .. an a look at the motor. Also tell us. What you done to motor
@lacolello66447 ай бұрын
Nice rigg buddy. I got one as well .... nothing wrong with 6cyl. Buddy. Keep it that way
@user-fr5jp5ph4b7 ай бұрын
thank you...........TJ....from POLAND
@clemleymamabear9298 ай бұрын
Yes my husband has a 71 c10
@dannycollingwood65287 ай бұрын
Well I Praise him for it!! Still wish to One Day mine. Been under a lot of OLD SCHOOL HOODS, BUT NOTHING BETTER THAN THE C-10 OLD SCHOOL CHEVY BABY!!
@dannycollingwood65288 ай бұрын
Heck YEAH!! IT'S GOT THAT LOPE AND KACKLE, probably burn those back tires off. Beautiful Sounds!
@TheLuv2PlayU8 ай бұрын
I love it! 🥰🥰
@dannycollingwood65287 ай бұрын
I know right, spent a lot of time under the Hood of those big block 350's, and every Chevy in-between. Nothing like-Em!!
@jackfrench33248 ай бұрын
Good video. I think it will help me with my 2000 TJ. You're right, some videos have too much talk and not enough action.
@user-fj6ts6bt7z8 ай бұрын
Thanks! I thought for sure I was going to break it, but it worked just like you showed us.
@MrsBuddevil9 ай бұрын
❤
@ewong85059 ай бұрын
🙈 Promo'SM
@walkinfaithnotbysight10 ай бұрын
Thanks a lot!!
@glenjaye6910 ай бұрын
Thank youy :)
@vincentthompson280510 ай бұрын
Great vid! Helped a lot.
@aaronjohnson455711 ай бұрын
Thank you for this video. It was extremely helpful to me!
@lacolello664411 ай бұрын
Need more video please
@lacolello664411 ай бұрын
Outstanding. Love them 6 cyl motors. One nice rig. Mate
@knockywigglesworth1909 Жыл бұрын
Slots can go either way. When the slots face to the rear you can replace bearing without a puller. Just rotate bearing & pull out.
@nickmonadi Жыл бұрын
Is your gauge cluster the original to the truck or just a factory style replacement? I have the same issue but with a new gauge so im wondering if that sender will fix it for mine. It is an aftermarket but its just like the original gauge.