i’ve never had to mess with one before so thx this sure helps out very muvh
@azizshavershian2065Күн бұрын
my OCD got the best of me and I drained and filled my P7B 22 times until it was pure distilled water coming out. then filled with pure coolant and used a glycol refractometer to ensure it was a proper mixture. this video just saved me about 2 months time in the future lol thx WJ
@sietze023Күн бұрын
Hi! So I've done this treatment in my 2011 P7B and used your video as a guide! Strangely there was no smoke when we sprayed the seafoam in. Only a little smoke after the 10 engine off. Have I missed something? Thanks voor the good videos and guides for Panther owners!
@WJHandyDadКүн бұрын
no way for me to know if you missed something. It's possible that you didn't have much carbon build up???
@jray2xx2 күн бұрын
What’s the size of the screws for the thermostat housing
@WJHandyDadКүн бұрын
unfortunately I don't know and I don't have any reliable method to figure it out
@tiremart73483 күн бұрын
I bought my cvpi 2010 for 4000 I wont sell it for 20000
@WJHandyDad2 күн бұрын
yep! This is the thing that so many folks don't understand. They remember the days of Crown Vics being auctioned off for $500-2,000 all day long. But that isn't the case any more, and cars for sale in the $20-30k range usually aren't offering everything that a good Crown Vic does. Most of the negative comments I get refer to Crown Vics not being as fast as this or that vehicle, but speed is only 1 factor to consider.
@carsonkimble17573 күн бұрын
I had hope for this fix. My contacts were bright and shiny. I cleaned them anyways. Underneath that screw-in thing are two large plates which I make sure are free of scum at start up. There are also two smaller protruding things. I am guessing maybe that is what senses the flow. They were discolored a little bit, so I cleaned on them some. Still no luck.
@WJHandyDad3 күн бұрын
these things can be frustrating... it's possible that one or more of the prongs is not making a good connection. I've run into intermittent issues with mine again even though no obvious signs.
@blupupher5 күн бұрын
I have an '02 F150 I have had for about 10 years and have had my mirror fall off at least once a year, if not more often. Have used several rear view adhesives and some last longer than others, but have all failed. Redid it about a month ago, and will see how it holds, but if it fails, may give this a try.
@WJHandyDad5 күн бұрын
knock on wood... so far it's holding up and we had a couple triple digit temps this year. I'm not sure if changing to the epoxy or moving it on the windshield was the "secret" since I did both, but I'm happy thus far!
@blupupher4 күн бұрын
I am in the Houston area, so understand the heat and sun issues. I have even gone a far as taking my dremel and cutting some little groves in the button hoping it would adhere better, since like you, it seems to stick to the glass but not the button.
@WJHandyDad4 күн бұрын
hope you're OK and safe from the flooding. We've had terrible rain and flooding, but nothing like what Houston has had. Lake Waco rose more than 10' in one day this month!
@loniebrown96465 күн бұрын
4.6 in a P71 is slower than a V6 Camry from 0 to 60 mph... Strength in a P71 is in numbers, low build costs, cant out run the radio.. You can put a Mustang engine in a tank, and get a tank, but no performance equal to a lighter car with more horsepower.. Every time I saw a p71 trying to get anywhere in a hurry, they were in constant labor...
@stevewhewell61905 күн бұрын
Gasoline in water jugs. Fire marshall - "We found what burned the structure down".
@jimlong5275 күн бұрын
Thank you, doing the same project tomorrow morning.
@andy_1826 күн бұрын
I thought it was only motor raft gold or zerex g05
@WJHandyDad5 күн бұрын
yes the original spec but the newest stuff is even better. I'll have to see if I can find it, but I believe there is a TSB saying to update all of them to the "yellow"
@andy_1825 күн бұрын
@@WJHandyDad oh okay. I just bought Zerex G05 per the manual recommendation. I'll have to look out for the TSB. thank you for the great video again
@WJHandyDad5 күн бұрын
not a TSB but this explains how it's backward compatible and better... www.ford-trucks.com/articles/everything-you-need-to-know-about-ford-motorcraft-yellow-coolant/
@andy_1825 күн бұрын
@@WJHandyDad thank you for the article, I’ll read it today!
@terrysimmons10207 күн бұрын
How do you get the sensor lose???
@WJHandyDad7 күн бұрын
mine just unscrews
@lorenray94798 күн бұрын
Carve a 1qt yogurt container to fit below loosened filter. Must be Nancy's 0rganic cut with a SakVic or you will get messy in protest! Lol
@leslietubb95429 күн бұрын
That mf LOUD asf! No thanks!
@dennistrull14759 күн бұрын
Wish there was more on how to determine which one needs the solder, and demo. Less on the light bulbs
@WJHandyDad8 күн бұрын
the safest thing is to resolder all of them
@quagmiredavis411710 күн бұрын
I have the task of repower some older vicks with the godzilla 7.3 finally a crown vic With some balls and teeth ... we even reuse 2 older polara 440 pursuit package cars Since the manufacturers have left us stranded 😅😊
@WJHandyDad10 күн бұрын
it would be so fun to build up one of these to at least 350-400hp. I'm not going to mess with either of mine though until the 4.6 gives out (which is not likely to happen in my lifetime)
@quagmiredavis411710 күн бұрын
@@WJHandyDad 4.6 gutless compared to 7.3 gas cubic inches wins
@maxpartido24711 күн бұрын
13:15 time stamp, you dont have to remove the whole hose, in the back of your dryer there should be this plastic cover that you can open like an oven door, then from there you will have access to where the hose connects. The hose should have this plastic lock which you can squeeze and pull out and it should just click back in as well once you put it back. Thank you for this in depth tutorial, I used it to fix our dryer which had a knocking sound. One of the rollers went bad and metal shaving was all over the dryer. Our dryer is 14 years old and all that lint inside looked like carpet. Definitely a fire hazard.
@WJHandyDad10 күн бұрын
thanks for the tip
@MM-jm7tt11 күн бұрын
Will this solenoid also prevent the transmission to be shifted back into Park, from Reverse? I can't get my car to go all the way into Park but the shifter cable seems fine.
@WJHandyDad10 күн бұрын
It shouldn't
@troyblackford-dowell117811 күн бұрын
I used a thumb tack. Poked a hole in the bottome of the jug. Drained the water and alcohol out, the replaced the tack, before poring the gas into the can.
@WJHandyDad10 күн бұрын
great idea! thanks for sharing
@eugenioalvesferreira740212 күн бұрын
Excelente!
@mellovato842112 күн бұрын
why do you have to raise the wheels of the ground?
@WJHandyDad12 күн бұрын
just makes it easier to turn the wheel back and forth and force out the old fluid
@chaleys_channel12313 күн бұрын
What is the clean button for ? Can’t figure it out our low salt won’t stop going off
@WJHandyDad12 күн бұрын
the low salt (assuming it's not really low salt) is usually a wiring fault like I showed. I believe the "clean" thing reverses polarity to remove the calcium buildup on the plates, which seems counterintuitive since it releases it back into the pool only to be trapped again. I like to soak in vinegar instead.
@user-bv5os2ts2e14 күн бұрын
I removed my 2014 Escalade ESV driver seat for deep cleaning purposes, when I reinstalled it, the 4 bolts wouldn't fall back in place, either the 2 on the right sit in place, or the 2 on the left, but not all of them together. after some scratching bold skull hours went by, and it appears the seat running plat is out of sync. how in the heck it did that/ it seems like it went sideways. Is anybody with a similar problem or experience on what went wrong and how to rectify it? thank you all in advance
@WJHandyDad13 күн бұрын
some vehicles the seat adjustment only is active on one side and the other is passive. You might be able to push the passive side back into alignment
@wetpossum15 күн бұрын
Fixed it for me, I think burping the air out made the difference as I had no corrosion. Thanks for posting.
@user-gh5if5oo2f16 күн бұрын
How do you service the wheels?
@WJHandyDad16 күн бұрын
I've never serviced them on this jack, I did on a Harbor Freight jack here: kzfaq.info/get/bejne/jdyedd2ZqK-WeGQ.html
@user-gh5if5oo2f16 күн бұрын
What jack is this? Anyone have a name?
@WJHandyDad16 күн бұрын
it's a Craftsman, the exact model is in the video description
@wM70AB16 күн бұрын
Thanks WJ HD. I've been a watcher for years since I had a Vic. Keep up the good work,
@rajajirajagopalan75617 күн бұрын
His hand is blocking the New when removing the cable. Bad
@VRidesNL17 күн бұрын
Got my gun for a day and it started leaking around the trigger. This video fixed it! Thanks!!
@AionMc_18 күн бұрын
ok so I'm trying to take it off because the seat motor is off, any suggestions
@WJHandyDad16 күн бұрын
you might be able to reach the bolts but it will be more difficult. Good luck
@leighmeeks2318 күн бұрын
What size is that long piece .. 2ft?
@WJHandyDad16 күн бұрын
I don't remember... I probably just held it up next to the ends and cut it
@markhubanks371518 күн бұрын
I'm doing this complete replacement on my Dodge Charger, Thank You for a great how to video!
@jamesrobinson842318 күн бұрын
How to install the center console & what’s the measurement
@WJHandyDad16 күн бұрын
I was lucky that mine still had that metal plate between the seats so I just screwed it into the plate. You can probably get away with just resting it between the seats too... that's how I have my Crown Vic - it's not bolted down and has never moved
@hormonesforme18 күн бұрын
Great video!
@SandraVincent-ic9ur19 күн бұрын
Mt 2011 acadia was friving fine at about 35 pulled to the rt. For split sec. Let alot of smoke from under the hood, (Not steam) stalled out & now does same as yours
@WJHandyDad18 күн бұрын
I eventually replaced the starter and it fired up.
@goincd319 күн бұрын
Ive always thought it was just my window motor dying. Sweet! Thanks for the tip.
@WJHandyDad18 күн бұрын
glad it helped
@kylemlm20 күн бұрын
Judge, fantastic work. Waiting you convert a vic into electric vehicle, maybe my better half ride in the vehicle. LOL
@antoniomarc717420 күн бұрын
Nice conversion…👍👍
@funvic20 күн бұрын
I hope all those CHARGES won't affect you at work...
@2006Mercury20 күн бұрын
Positively shocking
@richkuban202721 күн бұрын
Thanks for the easy fix. FYI, I found a faucet repair o-ring that fit perfectly at my local hardware store. Thanks for posting the dimensions, that was helpful. The one I found was for a water faucet, hope using it in hydraulic fluid won’t be a problem.
@WJHandyDad21 күн бұрын
Hopefully it will work. I've replaced mine one time since I filmed the video but my jack still works great
@evancohen701821 күн бұрын
I have a question. Hopefully you can answer. I tryed programming my remote to open and close the door. But it didnt work. I called the dealer told them i had a 2013 Ford Taurus Police Interceptor and gave then my vin # . They told me the car was ordered without a module. Anywhere I can check to verify it?
@WJHandyDad21 күн бұрын
I don't have access to any build data. You might be able to find with a google search of your VIN.
@thecatdaddy197422 күн бұрын
Step one, use every tool in box, Step two pry till it breaks, Step Three run to Home Depot and install new one. Got It
@WJHandyDad21 күн бұрын
LOL - if you watch closely the video does reveal how to open it without breaking although I had to break mine to figure it out
@bigmike472024 күн бұрын
What plugs would I use if my crown Vic is flex fuel 2006 year model
@WJHandyDad23 күн бұрын
405 are the "flex fuel" and 493 are the gas only
@SubaruAmbassadorRobert24 күн бұрын
Great vid! Mine is probably 20 years old, and has lasted through a dozen cars and SUVs, and trips all over the country, including being used off-road quite a bit. I'm amazed how well it still works, and this vid will help me make sure I get a bit more life out of it. Thanks!!!
@BenvanBroekhuijsen25 күн бұрын
It is better to use short hoses for the last part. The pool is flexible, the walls will move, the pipes will break like this.
@WJHandyDad24 күн бұрын
not a bad idea, but believe it or not, even with wild teenagers I've never had an issue with the pipes breaking and I've done this on several pools... the pools fail long before the PVC
@antoniomarc717425 күн бұрын
Nice work…👍👍
@Eric_D_Blair25 күн бұрын
🇺🇸
@Eric_D_Blair25 күн бұрын
STRANGE? I LEARNED THAT H²O won't/ dont& cant burn : unless you separate the H & O ~ Lindenhurst time💥 But: so do : " LITHIUM-ION " BATTERIES WE SIT ON IN EV CARS & TALK TO ~ WHEN THEY GET HOT & WET?