After we were done with the engraving, we very lightly vacuumed it with a soap, bristle brush to get any loose foot off the engraving. This way when we sprayed it with the clearcoat, it was sealed in and did not smear.

It’s supposed to say soft bristle brush, not soap

yes

I’m sorry, but I’m missing your point here.

Thank you so very much for the kind words and you are very very welcome

TY so very much!!

My files are ok with any laser....acesdeals.net/shop/ols/categories/flux-beamo-laser-png-files

Absolutely! We have thousands of visitors and our website every month and a lot of it is due to the help that this company offered us when we started with them

You are very, very welcome

I actually forgot to do that at the end of the video lol. When I get to the office tomorrow, I will definitely upload a picture of the end result. Thank you for reminding me.

@@lazerking1701 Where will I be able to see it?

I am trying to figure out a way to upload the pic here.....send me an email, [email protected] and I will reply with pic.

It can be done....

As I stated, in previous replies, once I was done, you’re going to have some loose soot . At that point, I lightly brushed whatever was loose and then I sprayed from a distance of about 12 inches a clear coating to protect the lettering.

You are so very very welcome. If you’re in the United States, and if you ever have any questions regarding this software or lasers in general because we repair and fix them and sell them, you can reach me at 888-2 39-2644 anytime after 9 AM Eastern

Don’t you just love it!

You are very welcome...visit us at www.acesdeals.net

After I’m done engraving using this method, I use that mini keyboard, vacuum cleaner and lightly vacuum up any loose soot . They approximately 8 inches away from the surface. I lightly spray it with a clear polyurethane gloss spray before I brush on a product called crystalac which provides a very smooth clear glass light finish.

@@lazerking1701 thank you.

I have to disagree with you "dude" It has worked well for us and thousands of others that use this method.

You are very welcome my friend. I’m glad I was able to help you in one way or another. I hope you subscribed.

You would have to go back to the video because I tell you the measurements

This software is designed to work for any CO2 or diode laser. It does not matter what laser you have. You prepare the image for laser engraving using this software, and then you bring it to the software that your computer has to engrave.

You can use sewing machine oil, but do not use WD-40 or any type of oil like that use sewing machine oil

@@lazerking1701 Thank you.

You simply measure the circumference of the Tumblr/cup the image will be bigger than the diameter of the cup on your screen, but it will wrap around

@@lazerking1701 ahh...so it will stick past glassware on both sides.

@@MasterTheNEC as long as your measurements are correct you should be fine

It can be a number of reasons as you do not provide any info as to what you are using or what you are doing...if you are in the US do not hesitate to call my office direct @631-730-7228...I am here till 6pm est in NY

Thank you so very very much!!

Sorry for delay....once done engraving I take a mini vac and suck away the majority of loose soot . The from 12--15" away I spray the clear coat. Dont spray close but from afar so the spray drifts down and locks the remaining soot in place.

You are very, very welcome.

Stay tuned for more! And thank you

We mfr our own ink and paper found here.....www.acesdeals.net

Thank you so very much for the compliment. If you ever have any questions if you’re located in the United States, feel free to call my office between 9 AM and 6 PM Eastern standard at 888-239-2644.

You are very welcome and I’m going to be doing a couple more videos on this program

I agree with you. You can go through 150 credits rather quickly I signed up with the $10 a month program which gives me 8500 credits that’s more than enough for me and each month it regenerates another 8500 credits, but does not rollover from previous month, if you ever have any questions, feel free to call my office and the number is listed above. Have a great day and I’m glad you enjoyed my video.

It’s 150 per day for free plan.

Thank you!!

I'm not sure what you are asking....is the press itself not level or is it the heating head of press not even setting down on bottom platen?

@@lazerking1701 I have it setting on a table but it seems that one side of the press presses better than the other side. Example: when I remove the paper after a press the transfer has not adhered to the fabric as well as it has on the other side. Hope this makes scene. (This is on larger transfers and yes the transfer fits on all sides)

@@Mary485 Now I understand....On page #5 of manual you will see bolts that you can adjust .....manualsfile.com/product/k2ooyrb592y.html Adjust accordingly so a pc of paper os nice and snug when press is closed.